saxby lighting 61219 Tri CCT Black IP65 LED Brick Light Instruction Manual
- September 11, 2024
- saxby lighting
Table of Contents
61219 Tri CCT Black IP65 LED Brick Light
“`html
Specifications:
-
Voltage: 240V 50Hz a.c.
-
Lamp: 1W LED Module (SMD 3014) Warm White –
42lm -
IP rating: 65
Product Usage Instructions:
Commissioning:
Ensure the light fitting is ready for use.
Fitting/Replacing Bulbs:
1. Use a soft dry cloth for cleaning.
2. Avoid solvents or abrasive cleaners to prevent damage to the
finish.
Recycling Advice:
Dispose of waste electrical products responsibly. Recycle where
facilities exist. Consult your Local Authority or retailer for
guidance.
Safety Information:
1. Always switch off the power supply before changing lightbulbs
or cleaning.
2. This system contains non-replaceable parts and should be
scrapped if damaged.
3. Replace the shade immediately if cracked or damaged. Do not
use the fitting without the shade.
Installation:
1. Completely remove existing fittings before installing the new
product.
2. Note the position of each set of wires before removal.
3. Install in accordance with IEE Wiring regulations and current
Building Regulations.
Wiring:
Identify the wiring from your light fitting and connect to the
approved outdoor rated external terminal block as instructed.
FAQ:
Check that…
[Include common issues or troubleshooting tips here]
“`
Commissioning
· When complete, wrap the terminal block in 2 layers of good quality
insulation tape.
· Re-fit the lens housing. · Diagram C. Re-fit the cover plate click in
position. · Replace fuse or circuit breaker and switch on. Your
light is now ready for use.
Diagram C.
Instruction leaflet
Severus Outdoor Wall
61219
Fitting/Replacing bulbs
· The LED module in this product is non replaceable
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
Recycling advice
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice.
Safety information
For your safety, always switch off the supply before changing lightbulbs, or
cleaning. This system contains non-replaceable parts and cannot be serviced.
If damage occurs the part should be scrapped.
This light source is protected by a shade. This part must be replaced
immediately should the shade become cracked or damaged. This fitting must not
be used without the shade in place.
www.saxbylighting.com
Iss.1 02062015 Saxby Lighting Ltd. BH23 3PE
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This light fitting is Double Insulated and does not require connection to an
Earth circuit.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building
Regulations.
To prevent electrocution switch off at mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge. If you are in any doubt, please consult a
qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
This system contains non-replaceable parts and cannot be serviced. If damage
occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
This product is rated at IP65.
This product is not suitable for location in or near a marine environment.
This product is not suitable for dimming.
Installation
Existing fittings must be completely removed before installation of a new
product. Before removing the existing fitting, carefully note the position of
each set of wires.
· Determine the position of your light fitting taking into account the entry
position of the cable and make sure there is sufficient cable coming out of
the wall to connect to the terminal block. Ensure that the mounting surface is
solid, preferably a brick or block wall and ensure that there are no other
cables or pipes beneath the surface.
· Diagram A. Gently prise off the cover plate to reveal the 4 retaining screws
on the sides of the unit. Unscrew these to remove the lens housing.
· Diagram B. Bring the mains cable through the rubber grommet in the wall
plate and then use the wall plate as a template and mark the fixings holes,
making sure the wall plate is correctly aligned so that the top of it is
horizontal. Use appropriate fixings to secure the back plate to the wall.
· Wire as detailed below.
Diagram A.
Cover plate
Diagram B.
Lens housing
Wall plate Mounting screws
Grommet
Incoming supply
Specification
Voltage: Lamp: IP rating:
240V 50Hz a.c. 1W LED Module (SMD 3014) Warm White – 42lm 65
Layout
· Plan the desired layout of this fitting carefully, ensuring the cables will
reach the distance between the junction box and the light fitting.
· Avoid locating any cables in positions that would cause a hazard. Position
cables and outdoor rated junction boxes (not supplied) away from areas where
they may be at risk from being cut, trapped or damaged.
· We recommend that you use H05RN-F specification cable which is an outdoor
grade, rubber sheathed cable. The mains supply cable must have a minimum cross
sectional area of 1.0mm²
· Cables must be protected using suitable conduit or plastic trunking.
Wiring
Having correctly identified the wiring from your light fitting, connect to the
approved outdoor rated external
terminal block in the following way:
Check that…
· You have correctly identified the wires · The connections are tight
· No loose strands have been left out of the connection block.
· Reseal the approved outdoor rated external terminal block.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>