RUUD WP14AZA Endeavor Line Choice Series iC Heat Pump User Manual

RUUD WP14AZA Endeavor Line Choice Series iC Heat Pump

Features and Benefits

• Fully Louvered Steel Cabinet: Features durable construction to add protection from yard hazards, weather corrosion
• Two-Stage Scroll Compressor: Features two speeds (high and low) of cooling and heating, providing more precise emperature conto. lower numion and greater enciency when compared to single stage compressors
• Inverted Reversing Valve: Allows for faster heat transfer with gravity assist shifting and reduced joint stress for increased reliability
• Easily Accessible Control Box: Ease of installation and serviceability

Heat Pumps

Designates Metric Conversions

AVAILABLE MODELS

WP14AZ18AJ1 N
WP14AZ18AJ2N
WP14AZ24AJ2N
WP14AZ30AJ2N
WP14AZ36AJ2N
WP14AZ42AJ2N
WP14AZ48AJ2N
WP14AZ60AJ2N
STANDARD EQUIPMENT

R-41DA Refrigerant
Scroll Compressor
Field Installed Filter Drier
Front Seating Service Valves
Internal Pressure Relief Valve
Internal Thermal Overload
Long Line capability
Low Ambient capability with Kit
3-4-5 Expanded Valve Space
Composite Basepan
2 Screw Control Box Access
15″ Access to Internal Components
Quick release louver panel design
No fasteners to remove along bottom
Optimized Venturi Airflow
Single row condenser coil
Powder coated paint
Rust resistant screws
QR code
External gauge ports
Service trays

General Data

Electrical Data

Line Voltage Data (Volts-Phase-Hz)| 208/230-1-60| 208/230-1- 60| 208/230-1- 60| 208/230-1- 60| 208/230-1- 60| 208/230-1- 60| 208/230-1-60| 208/230-1- 60
---|---|---|---|---|---|---|---|---
Maximum overcurrent protection (amps) 2| 20| 15| 20| 25| 25| 35| 35| 40
Minimum circuit ampacity 3| 11| 11| 15| 18| 21| 26| 29| 31
Compressor|
Rated load amps| 10| 8| 11| 13| 15| 20| 22| 24
Locked rotor amps| 46| 56| 66| 71| 78| 151| 0| 118
Condenser Fan Motor|
Full loacl amps| 0.75| 0.75| 0.75| 1.0| 1.0| 1.0| 1.0| 1.0
Locked rotor amps| 1.4| 1.4| 1.5| 2.6| 2.56| 2.56| 2.56| 2.6

1. Refrigerant charge sufficient for 15 ft. length of refrigerant lines. For longer line set requirements see the installation instructions for information about set length and additional refrigerant charge required.
2. HACR type circuit breaker of fuse.
3. Refer to National Electrical Code manual to determine wire, fuse and disconnect size requirements.

Accessories

MODEL NO .| WP14AZ18.. 1| WP14AZ18.. 2| WP14AZ24| WP14AZ30| WP14AZ36| WP14AZ42| WP14AZ48| WP14AZ60
---|---|---|---|---|---|---|---|---
Compressor crankcase heater•| 44-17402-44| 44-17402-44| 44-17402-44| 44-17402-44| 44-17402-44| 44-17402-45| 44-17402-45| Factory Standard
Low ambient control| RXAD-A08| RXAD-A08| RXAD-A08| RXAD-A08| RXAD-A08| RXAD-A08| RXAD-A08| RXAD-A08
Compressor sound cover| 68-23427-26| 68-23427-26| 68-23427-26| 68-23427-26| 68-23427-26| 68-23427-25| 68-23427-25| 68-23427-25
Compressor hard start kit| SK-A1| SK-A1| SK-A1| SK-A1| SK-A1| SK-A1| SK-A1| SK-A1
Low pressure control| Factory Standard| Factory Standard| Factory Standard| Factory Standard| Factory Standard| Factory Standard| Factory Standard| Factory Standard
High pressure control| Factory Standard| Factory Standard| Factory Standard| Factory Standard| Factory Standard| Factory Standard| Factory Standard| Factory Standard
Liquid Line Solenoid (24 VAC, 50/60 Hz)| Solenoid Valve| 200RD2T3TVLC| 200RD2T3TVLC| 200RD2T3TVLC| 200RD2T3TVLC| 200RD2T3TVLC| 200RD2T3TVLC| 200RD3T3TVLC| 200RD3T3TVLC
Solenoid Coil| 61-AMG24V| 61-AMG24V| 61-AMG24V| 61-AMG24V| 61-AMG24V| 61-AMG24V| 61-AMG24V| 61-AMG24V
Liquid Line Solenoid (120/240 VAC, 50/60 Hz)| Solenoid Valve| 200RD2T3TVLC| 200RD2T3TVLC| 200RD2T3TVLC| 200RD2T3TVLC| 200RD2T3TVLC| 200RD2T3TVLC| 200RD3T3TVLC| 200RD3T3TVLC
Solenoid Coil| 61-AMG120/240V| 61-AMG120/240V| 61-AMG120/240V| 61-AMG120/240V| 61-AMG120/240V| 61-AMG120/240V| 61-AMG120/240V| 61-AMG120/240V
Classic Top Cap w/Label| 91-101123-21| 91-101123-21| 91-101123-21| 91-101123-21| 91-101123-21| 91-101123-21| 91-101123-21| 91-101123-21

Bi-flow kits are required when installing a liquid line solenoid on a heat pump.

Weighted Sound Power Level (dBA)

UNIT SIZE· VOLTAGE, SERIES| STANDARD RATING (DBA)| TYPICAL OCTAVE BAND SPECTRUM (dBA without tone adjustment)
---|---|---
125| 250| 500| 1000| 2000| 4000| 8000
WP14AZ18A| 73| 39.8| 55| 62.1| 67.0| 60.0| 57.4| 51.2
WP14AZ24A| 73| 40.4| 55.4| 62.5| 65.9| 58.7| 56.4| 48.9
WP14AZ30A| 72| 48.9| 55.3| 63.6| 61.0| 59.1| 56.5| 48.7
WP14AZ36A| 72| 50.1| 55.8| 64.4| 61.5| 58.7| 55.1| 50.9
WP14AZ42A| 72| 48.6| 56.2| 63.1| 61.7| 60.0| 56| 50.0
WP14AZ48A| 74| 49.3| 56| 64.5| 64.5| 60.1| 54.9| 47.7
WP14AZ60A| 74| 43.9| 55.2| 63.4| 65.8| 61.7| 57.9| 52.9

NOTE: Tested in accordance with AHRI Standard 270-08 (not listed in AHRI)

Unit Dimensions

MODEL NO.

| OPERATING| SHIPPING
---|---|---
H (Height)| L (Length)| W (Width)| H (Height)| L (Length)| W (Width)
INCHES| mm| INCHES| mm| INCHES| mm| INCHES| mm| INCHES| mm| INCHES| mm
WP14AZ181| 25.17| 639| 29.543| 750| 29.543| 750| 27.0625| 687| 32.625| 829| 32.625| 829
WP14AZ182| 25.17| 639| 29.543| 750| 29.543| 750| 27.0625| 687| 32.625| 829| 32.625| 829
WP14AZ24| 25.17| 639| 29.543| 750| 29.543| 750| 27.0625| 687| 32.625| 829| 32.625| 829
WP14AZ30| 27.17| 690| 33.655| 855| 33.655| 855| 29.0625| 738| 36.625| 930| 36.625| 930
WP14AZ36| 35.17| 893| 33.655| 855| 33.655| 855| 37.0625| 941| 36.625| 930| 36.625| 930
WP14AZ42| 35.17| 893| 33.655| 855| 33.655| 855| 37.0625| 941| 36.625| 930| 36.625| 930
WP14AZ48| 35.17| 893| 33.655| 855| 33.655| 855| 37.0625| 941| 36.625| 930| 36.625| 930
WP14AZ60| 45.17| 1147| 35.543| 903| 35.543| 903| 47.0625| 1195| 38.625| 981| 38.625| 981

CLEARANCES

NOTE: NUMBERS IN () = mm
IMPORTANT : When installing multiple units in an alcove, roof well or partially enclosed area, ensure there is adequate ventillation to prevent re- circulation of discharge air.

Control Wiring

FIGURE4
CONTROL WIRING FOR AIR HANDLER

NOTES:

1. Jumper “E” to “W2” to transfer control of supplemental heat to 1st stage when the emergency heat switch is on .
2. This wire turns on heat for defrost, omit for most economical operation.
3. Wire with colored tracing stripe.

NOTE: RED WIRE REQUIRED WITH RANCO DDL DEMAND DEFROST CONTROL.

WIRING INFORMATION Line Voltage

• Field Installed ———————
• Factory Standard——————

Application Guidelines

1. Intended for outdoor installation with free air inlet and outlet. Outdoor fan external static pressure available is less than 0.01 -in. wc.
2. Minimum outdoor operation air temperature for cooling mode without low-ambient operation accessory is 55°F (12.8°C).
3. Maximum outdoor operating air temperature is 125° F (51.7°C).
4. For reliable operation, unit should be level in all horizontal planes.
5. Use only copper wire for electric connections at unit. Aluminum and clad aluminum are not acceptable for the type of connector provided.
6. Do not apply capillary tube indoor coils to these units.
7. Factory-supplied filter drier must be installed.

Refrigerant Line Size Information

14 . 3 SEER2 HEAT PUMPS

UNIT SIZE

| MAX . LIQUID LINE SIZE| SUCTION LINE SIZE| EQUIVALENT LENGTH (FEET)
< 15| 16- 25| 26- 50| 51- 80| 81- 100| 101- 125| 126- 150
MAXIMUM VERTICAL SEPARATION/CAPACITY MULTIPLIER

1.5 Ton Sing le-Stage

| 1/4″| 5/8″| 15 / 1.00| 25 / 1.00| 50 I 0.99| 60 I 0.97| 45 I 0.96| 10 / 0.95| N/A
5/16″| 5/8″| 15 / 1.00| 25 / 1.00| 50 / 0.99| 75 / 0.97| 90 I 0.96| 45 / 0.95| N/A
3/8″| 5/8″| 15 / 1.00| 25 / 1.00| 50 / 0.99| 75 / 0.97| 95 / 0.96| 80 / 0.95| N/A

1.5 Ton Two-Stage

| 1/4″| 1/2″| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 I 0.96| 50 I 0.95| N/A| N/A
5/16″| 1/2″| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 I 0.96| 50 I 0.95| N/A| N/A
3/8”| 1/2″| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 / 0.96| 50 / 0.95| N/A| N/A
1/4″| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.98| 50 / 0.97| 50 / 0.96| 50 / 0.95| 50 / 0.94
5/16″| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.98| 50 I 0.97| 50 / 0.96| 50 I 0.95| 50 I 0.94
3/8”| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.98| 50 I 0.97| 50 / 0.96| 50 / 0.95| 50 / 0.94

2 Ton Two-Stage

| 1/4″| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.99| 31 / 0.97| 3 / 0.97| N/A| N/A
5/16″| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.99| 50 I 0.97| 50 / 0.97| 50 / 0.96| 50 / 0.95
3/8″| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.99| 50 I 0.97| 50 / 0.97| 50 / 0.96| 50 / 0.95

2.5 Ton Two-Stage

| 1/4″| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 I 0.96| 46 I 0.95| 50 / 0.94| N/A
5/16″| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 I 0.96| 50 / 0.95| 50 / 0.94| N/A
3/8″| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 I 0.96| 50 / 0.95| 50 / 0.94| N/A
1/4″| 3/4″| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 / 0.98| 50 / 0.98| 50 / 0.96| 50 / 0.95
5/16″| 3/4″| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 / 0.98| 50 / 0.98| 50 / 0.96| 50 / 0.95
3/8″| 3/4″| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 I 0.96| 50 I 0.96| 50 I 0.96| 50 I 0.95

3Ton Two-Stage

| 5/16″| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 I 0.95| 50 / 0.93| 50 I 0.91| N/A
3/8″| 5/8″| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 I 0.95| 50 / 0.93| 50 / 0.91| N/A
5/16″| 3/4″| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 I 0.96| 50 / 0.98| 50 / 0.97| 50 / 0.96
3/8″| 3/4″| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 I 0.96| 50 / 0.98| 50 / 0.97| 50 / 0.96
1/2″| 3/4″| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 I 0.96| 50 / 0.98| 50 I 0.97| 50 I 0.96

3.5 Ton Two-Stage

| 3/8″| 3/4″| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 I 0.97| 50 I 0.97| 50 I 0.96| 50 I 0.96
1/2″| 3/4″| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 I 0.97| 50 / 0.97| 50 / 0.96| 50 / 0.96
3/8″| 7/8″| 15 / 1.00| 25 / 0.99| 15/1.00| 50 I 0.96| 50 / 0.98| 50 / 0.97| 50 / 0.97
1/2″| 7/8″| 15 / 1.00| 25 / 0.99| 15 / 1.00| 50 I 0.96| 50 / 0.98| 50 I 0.97| 50 I 0.97

4 Ton Two-Stage

| 3/8”| 3/4″| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 I 0.97| 50 I 0.95| 50 I 0.94| 50 I 0.93
1/2″| 3/4″| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 I 0.97| 50 I 0.95| 50 / 0.94| 50 / 0.93
3/8″| 7/8″| 15 / 1.00| 25 / 0.99| 50 / 1.00| 50 I 0.97| 50 I 0.96| 50 / 0.98| 50 / 0.97
1/2″| 7/8″| 15 / 1.00| 25 / 0.99| 50 / 1.00| 50 / 0.97| 50 / 0.98| 50 / 0.98| 50 / 0.97

5 Ton Two-Stage

| 3/8”| 3/4″| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 / 0.95| 50 / 0.93| 50 / 0.91| N/A
1/2″| 3/4″| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 I 0.95| 50 I 0.93| 50 I 0.91| N/A
3/8″| 7/8″| 15 / 1.00| 25 / 0.99| 40 I 0.99| 15 / 0.99| 50 I 0.96| 50 I 0.97| 50 / 0.96
1/2″| 7/8″| 15 / 1.00| 25 / 0.99| 50 / 1.00| 50 I 0.99| 50 / 0.98| 50 / 0.97| 50 / 0.96

NOTES:

1. Do not exceed 200 ft linear line length.
2. Do not exceed 100 ft vertical separation if outdoor unit is above indoor unit.
3. Always use the smallest liquid line allowable to minimize refrigerant charge.
4. Applications shaded in light gray indicate capacity multipliers between 0.90 and 0.96 which are not recommended, but are allowed.
5. Applications shaded in dark gray are not recommended due to excessive liquid or suction pressure drop.

14 . 3 SEER2 HEAT PUMPS

UNIT SIZE

| MAX .

LIQUID LINE SIZE

mm[in . J

| SUCTION LINE SIZE

mm [in . I

| EQUIVALENT LENGTH (METERS)
0- 4 . 5| 5- 7 . 5| 8- 15| 15.5- 23| 23 . 5- 30| 30.5 – 38| 38 . 5- 46
MAXIMUM VERTICAL SEPARATION/CAPACITY MULTIPLIER
5.3 KW [1.5 Ton]

Single-Stage

| 6.35 [1/4]| 15.88 [5/8]| 15 / 1.00| 25 / 1.00| 50 I 0.99| 60 I 0.97| 45 / 0.96| 10 / 0.95| N/A
7.94 [5/16]| 15.88 [5/8]| 15 / 1.00| 25 / 1.00| 50 I 0.99| 75 / 0.97| 90 I 0.96| 45 / 0.95| N/A
9.53 [3/8]| 15.88 [5/8]| 15/1.00| 25 / 1.00| 50 I 0.99| 75 / 0.97| 95 / 0.96| 80 / 0.95| N/A

5.3 KW [1.5 Ton] Two-Stage

| 6.35 [1/4]| 12.70 [1/2]| 15 / 0.99| 25 / 0.99| 50 I 0.97| 50 I 0.96| 50 I 0.95| N/A| N/A
7.94 [5/16]| 12.70 [1/2]| 15 / 0.99| 25 / 0.99| 50 I 0.97| 50 / 0.96| 50 / 0.95| N/A| N/A
9.53 [3/8]| 12.70 [1/2]| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 / 0.96| 50 / 0.95| N/A| N/A
6.35 [1/4]| 15.88 [5/8]| 15 / 0.99| 25 / 0.99| 50 / 0.98| 50 / 0.97| 50 / 0.96| 50 / 0.95| 50 / 0.94
7.94 [5/16]| 15.88 [5/8]| 15 / 0.99| 25 / 0.99| 50 / 0.98| 50 / 0.97| 50 / 0.96| 50 / 0.95| 50 / 0.94
9.53 [3/8]| 15.88 [5/8]| 15 / 0.99| 25 / 0.99| 50 / 0.98| 50 / 0.97| 50 / 0.96| 50 / 0.95| 50 / 0.94
7.0 KW [2 Ton]

Two-Stage

| 6.35 [1/4]| 15.88 [5/8]| 15 / 0.99| 25 / 0.99| 50 / 0.99| 31 / 0.97| 3 / 0.97| N/A| N/A
7.94 [5/16]| 15.88 [5/8]| 15 / 0.99| 25 / 0.99| 50 / 0.99| 50 / 0.97| 50 / 0.97| 50 / 0.96| 50 / 0.95
9.53 [3/8]| 15.88 [5/8]| 15 / 0.99| 25 / 0.99| 50 / 0.99| 50 / 0.97| 50 / 0.97| 50 / 0.96| 50 / 0.95

8.8 KW [2.5 Ton] Two-Stage

| 6.35 [1/4]| 15.88 [5/8]| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 / 0.96| 46 I 0.95| 50 / 0.94| N/A
7.94 [5/16]| 15.88 [5/8]| 15/0.99| 25 / 0.99| 50 / 0.97| 50 / 0.96| 50 / 0.95| 50 / 0.94| N/A
9.53 [3/8]| 15.88 [5/8]| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 / 0.96| 50 / 0.95| 50 / 0.94| N/A
6.35 [1/4]| 19.05 [3/4]| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 / 0.98| 50 / 0.98| 50 / 0.96| 50 / 0.95
7.94 [5/16]| 19.05 [3/4]| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 / 0.98| 50 / 0.98| 50 / 0.96| 50 / 0.95
9.53 [3/8]| 19.05 [3/4]| 15/1.00| 25 / 0.99| 50 / 0.98| 50 / 0.98| 50 / 0.98| 50 / 0.96| 50 I 0.95

10.6 KW [3 Ton]

Two-Stage

| 7.94 [5/16]| 15.88 [5/8]| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 / 0.95| 50 I 0.93| 50 / 0.91| N/A
9.53 [3/8]| 15.88 [5/8]| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 / 0.95| 50 / 0.93| 50 / 0.91| N/A
7.94 [5/16]| 19.05 [3/4]| 15/1.00| 25 / 0.99| 50 / 0.98| 50 / 0.98| 50 / 0.98| 50 / 0.97| 50 / 0.96
9.53 [3/8]| 19.05 [3/4]| 15/1.00| 25 / 0.99| 50 / 0.98| 50 / 0.98| 50 / 0.98| 50 / 0.97| 50 / 0.96
12.70 [1/2]| 19.05 [3/4]| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 / 0.98| 50 / 0.98| 50 / 0.97| 50 / 0.96

12.3 KW [3.5 Ton] Two-Stage

| 9.53 [3/8]| 19.05 [3/4]| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 / 0.97| 50 / 0.97| 50 I 0.96| 50 I 0.96
12.70 [1/2]| 19.05 [3/4]| 15/1.00| 25 / 0.99| 50 / 0.98| 50 / 0.97| 50 / 0.97| 50 / 0.96| 50 / 0.96
9.53 [3/8]| 22.23 [7/8]| 15/1.00| 25 / 0.99| 15/1.00| 50 / 0.98| 50 / 0.98| 50 / 0.97| 50 / 0.97
12.70 [1/2]| 22.23 [7/8]| 15 / 1.00| 25 / 0.99| 15 / 1.00| 50 / 0.98| 50 / 0.98| 50 / 0.97| 50 I 0.97

14.1 KW [4 Ton]

Two-Stage

| 9.53 [3/8]| 19.05 [3/4]| 15 / 1.00| 25 / 0.99| 50 / 0.98| 50 / 0.97| 50 / 0.95| 50 / 0.94| 50 I 0.93
12.70 [1/2]| 19.05 [3/4]| 15/1.00| 25 / 0.99| 50 / 0.98| 50 / 0.97| 50 / 0.95| 50 / 0.94| 50 / 0.93
9.53 [3/8]| 22.23 [7/8]| 15/1.00| 25 / 0.99| 50 / 1.00| 50 / 0.97| 50 / 0.98| 50 / 0.98| 50 / 0.97
12.70 [1/2]| 22.23 [7/8]| 15 / 1.00| 25 / 0.99| 50 / 1.00| 50 / 0.97| 50 / 0.98| 50 / 0.98| 50 / 0.97

17.6 KW [5 Ton]

Two-Stage

| 9.53 [3/8]| 19.05 [3/4]| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 / 0.95| 50 / 0.93| 50 / 0.91| N/A
12.70 [1/2]| 19.05 [3/4]| 15 / 0.99| 25 / 0.99| 50 / 0.97| 50 / 0.95| 50 / 0.93| 50 / 0.91| N/A
9.53 [3/8]| 22.23 [7/8]| 15/1.00| 25 / 0.99| 40 I 0.99| 15 / 0.99| 50 / 0.98| 50 / 0.97| 50 I 0.96
12.70 [1/2]| 22.23 [7/8]| 15/1.00| 25 / 0.99| 50 / 1.00| 50 / 0.99| 50 / 0.98| 50 / 0.97| 50 / 0.96

NOTES:

1. Do not exceed 61 m linear line length.
2. Do not exceed 30m vertical separation if outdoor unit is above indoor unit.
3. Always use the smallest liquid line allowable to minimize refrigerant charge.
4. Applications shaded in light gray indicate capacity multipliers between 0.90 and 0.96 which are not recommended, but are allowed.
5. Applications shaded in dark gray are not recommended due to excessive liquid or suction pressure drop.

Performance Data @ AHRI Standard Conditions – Cooling

DESIGNATED TESTED COMBINATION (DTC)

OUTDOOR UNIT

| ****

AIR HANDLER

| TOTAL CAPACITY BTU/H [kW)| NET SENSIBLE BTU/H [kW)| NET LATENT BTU/H [kW)| ****

SEER2

| ****

EER2

| ****

INDOOR CFM IL/SI

| 47 DEGREE HEATING CAPACITY BTU/H [KW)| 47

DEGREE COP

| 17 DEGREE HEATING CAPACITY BTU/H [KW)| 17

DEGREE COP

| REGION IV HSPF2
WP14AZ18AJ1| RH2TZ2417STANN| 17,100 [5.0]| 13,100 [3.8]| 4,000 [1.2]| | | ,575 [271.4]| 17,100 [5.0]| | 11,100 [3.3]| |
WP14AZ18AJ2| RH2TZ2417STANN| 17,100 [5.0]| 13,100 [3.8]| 4,000 [1.2]| ,550 [259.6]| 17,100 [5.0]| 11,000 [3.2]
WP14AZ24AJ2| RH2TZ2417STANN| 22,800 [6.7]| 17,500 [5.1]| 5,300 [1.6]| ,775 [365.8]| 22,800 [6.7]| 14,600 [4.3]
WP14AZ30AJ2| RH2TZ3617STANN| 28,600 [8.4]| 21,900 [6.4]| 6,700 [2.0]| ,950 [448.4]| 28,600 [8.4]| 18,200 [5.3]
WP14AZ36AJ2| RH2TZ3617STANN| 34,200 [10.0]| 26,200 [7.7]| 8,000 [2.3]| 1,050 [495.5]| 34,200 [10.0]| 23,600 [6.9]
WP14AZ42AJ2| RH2TZ4821STANN| 39,500 [11.6]| 30,300 [8.9]| 9,200 [2.7]| 1,275 [601.7]| 39,500 [11.6]| 25,500 [7.5]
WP14AZ48AJ2| RH2TZ4821STANN| 45,500 [13.31| 34,900 [10.21| 10,600 [3.1l| 1,450 [684.3]| 45,500 [13.0]| 27,500 [8.1]
WP14AZ60AJ2| RH2TZ6024STANN| 55,500 [16.3]| 42,600 [12.5]| 12,900 [3.8]| 1,800 [849.5]| 55,500 [16.3]| 34,000 [10.0]

NOTE: This data includes DTC (Designated Test Combination) ratings and is for reference purposes only. A full listing of official ratings and system match-ups, along with downloadable certificates, can be accessed from the AHRI website: www.ahridirectory.org.

GENERAL TERMS OF LIMITED WARRANTY

• Ruud will furnish a replacement for any part of this product that fails in normal use and service within the applicable period stated, in accordance with the terms of the limited warranty.

For complete details of the Limited and Conditional Warranties, including applicable terms and conditions, contact your local contractor or the Manufacturer for a copy of the product warranty certificate.

Before proceeding with installation, refer to installation instructions packaged with each model, as well as comply with all Federal, State, Provincial, and Local codes, regulations, and practices.
© 2023 Rheem Manufacturing Company. Ruud trademarks are owned by Rheem Manufacturing Company.
In keeping with its policy of continuous progress and product improvement, Ruud reserves the right to make changes without notice.

Ruud Heating, Cooling & Water Heating

• 5600 Old Greenwood Road Fort Smith, Arkansas 72908
• www.ruud.com

Ruud Canada Ltd./Ltee

• 125 Edgeware Road, Unit 1 Brampton, Ontario
• L6Y OPS
• ruud-canada.ca

PRINTED IN U.S.A. 5/23 QG FORM NO. P44-829 REV. 2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>