CYGNETT CY3458WLCCH ExoDrive Wireless Dash User Manual
- June 5, 2024
- CYGNETT
Table of Contents
CYGNETT CY3458WLCCH ExoDrive Wireless Dash
OVERVIEW
- Suction pad for windscreen attachment
- Locking lever for suction pad
- Adjustable ball joint for tightening ring
- Micro-USB input
- Wireless charging output
- Quick release button
Installation Instructions
Windscreen mounting
Attach the product to your windscreen by lifting the locking lever (B) to the
up position. Place the wireless charger in the desired
against the glass. Press down the locking lever (B) to lock into place, and
check it is securely attached. To remove, lift the locking lever and pull the
small tab on the suction pad.
Adjusting the viewing angle
Adjust the angle by loosening the tightening ring (C) of the ball joint on the
back of the product. Once you are happy with the viewing angle, tighten the
ring (C) to hold in place.
Connecting the power source
end into the 12V USB Car Adapter and plug into your vehicle’s 12V power
socket.
Charge your device wirelessly
To wirelessly charge your device, place your device on the wireless charging
output (E) and secure it with the retractable arms. To remove your device,
press the quick release button (F) to open the retractable arms.
PRODUCT SPECIFICATIONS
- Name ExoDrive Wireless Dash
- Item Number CY3458WLCCH
- Micro-USB Input 5.0V⎓2.0A (10.0W) 9.0V⎓2.0A (18.0W)
- Wireless Output 5.0W 7.5W 10.0W
- Total Output 10.0W
- Working Frequency Bands (For CE) 109.94kHz-165.38kHz
- Max Output Power (For CE) -17.79dBuA/m@10m
- FCC ID 2AEDZCY345XWLCCH
Troubleshooting
Not charging or slow charging Please ensure you are using the supplied power adapter within the wireless charger. Using other chargers may result in slow charging or no charge at all. If you need to replace the power adapter, please make sure it supports QC 3.0 and supports a 12V USB output. For optimum charge speed, adjust your device so that it is aligned to the centre of the wireless charging by removing it and checking the performance. Some cases interfere with wireless charging if they contain metallic material or are overly thick.
Caution
- Do not expose to extreme weather conditions.
- Do not place close to a magnetic strip or strip card as it could cause magnetic failure.
- Please keep charger a safe distance of at least 80cm from any implantable medical devices to avoid medical device interference.
- This is not a toy and should be kept away from children.
- In the case of the device overheating, please disconnect immediately.
approved by the party responsible for compliance could void the user’s authority to operate the equipment. Cygnett takes no responsibility for damages caused by incorrect use of its products. Made in China. Cygnett and the Cygnett logo are trademarks of Cygnett Pty Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders.
FCC
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. “FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.”
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is
no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by try to connect the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a Circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>