CYGNETT ChargeTree Mag 3In1 Magnetic Wireless Charging Stand Instruction Manual
- June 12, 2024
- CYGNETT
Table of Contents
3 in 1 Magnetic Wireless Charging Stand
Model: ChargeTree Mag
Product parameters
Input interface: USB-C
Input: 9V/3A 12V/2.5A
Phone charging output: 15W Max
Watch output: 3W Max
Earphone output: 5W Max
Material: ABS
Led light Indicates:
- When power connected , the white led lights on and shinking for 3 times and then off to indicate standby.
- When charging the device, the led lights on for 30 seconds and then off to indicate charging.
- When all devices are fully charged, led still lights off;
- If the wireless charging working abnormally or mismatch the wrong device,the white led lights on shinking.
Instructions for use:
- Power source connected to be in standby.
- Put cell Phone on the Magnetic charging area to start wireless charging;
- Put Apple Watch on the charging area to start wireless charging.
- Put TWS earphone on the charging area to start wireless charging. If cell phone with protected case, it needs magnetic, otherwise it affects magnetic strongth
Abnormal charging Checking:
- Please confirm your mobile phone with wireless charging function before use;
- Check if mobile phone deviates from the wireless charging right area of the charger;
- Whether a non-metallic protective case is used for charging mobile phones, and the thickness of the case should be less than 4mm;
- When metal material on the charging area, the charger will automatically identify and power off protection.
- When the temperature of the charger is too high, it will automatically start the protection.Please power off the charger firstly and then use it after the charger cool down to normal temperature.
Q & A :
Q:Why is there heating in the charging of wireless charging area when charging the device?
A:During the charging process, there will be a certain loss of magnetoelectric conversion, which will be converted into heat, causing the mobile phone and charger to generate heat, which is a normal Physical principle. Suggestions: When the device is fully charged, disconnect it from charging in time to avoid a long cycle of charging, which may lead to continuous heating of the device and charger; It is recommended to stop running the background software when charging the phone.
Attention：
- Use indoor or under dry environment, avoid placing or using in the environment of high temperature, humidity, strong static electricity and strong magnetic field.
- For your safety, please do not plug and unplug electrical appliances with wet hand.
- Avoid infants and children can touch easily.
- Do not use the product if it is contaminated with water or dirty.
- Non-professional personal are not allowed to open and repair this product without authorization.
FCC Warning Statement: Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that
may cause undesired operation.
FCC Radiation Exposure Statement
The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
co‐located for operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>