Kwikset Powerbolt 250 Keypad Electronic Lock User Guide

Kwikset Powerbolt 250 Keypad Electronic Lock

Product Information

The product is a Kwikset SmartCode 913 Electronic Deadbolt with a keypad. The package includes a latch, interior assembly, exterior assembly, transitional, contemporary, and two keys.
The deadbolt requires batteries and can be unlocked using the keypad or a key. It is compatible with doors that are either 2-1/8 in (54 mm) or 1-1/2 in (38 mm) thick and have a backset of either 2-3/8 or 2-3/4 in (60 or 70 mm).
The product comes with required tools, including batteries, a ruler, screwdrivers, and additional tools such as a hammer, wood block, adapter ring, mounting plate, strike, and collar.

Product Usage Instructions

1. Prepare the door and check dimensions:
   • If drilling a new door, use the supplied template and complete door drilling instructions available at www.kwikset.com/doorprep.
   • Confirm that the door is either 2-1/8 in (54 mm) or 1-1/2 in (38 mm) thick with a backset of either 2-3/8 or 2-3/4 in (60 or 70 mm).
   • Additional door preparation may be required for doors with 1-1/2 in (38 mm) holes. Consult the deadbolt drilling instructions at www.kwikset.com/doorprep.
   • Confirm that the door edge is 1 in (25 mm) and between 1-3/8 and 1-3/4 in (35 mm and 44 mm) thick. If the door thickness exceeds 1-3/4 in, contact customer service for a thick door kit.
2. Install the latch and strike:
   • Hold the latch in front of the door hole and confirm that the rectangular-shaped hole is centered in the door hole. If not, rotate the latch face as shown to extend the latch.
   • If the door edge is chiseled, install the strike on the door frame. If not, remove the latch face with a flathead screwdriver, twist collar off, and install drive-in collar.
   • Install the latch in the door with supplied screws. Make sure the hole in the door frame is drilled at least 1 in (25 mm) deep and that the slotted hole is at the bottom of the latch. Align tabs with holes in collar and ensure collar snaps into place. Install latch in the door with wood block and hammer. Make sure the latch bolt is fully retracted (in the unlocked position).
3. Install the exterior keypad:
   • Confirm the diameter of the hole in the door. If it is 2-1/8 in (54 mm), an adapter ring is not needed for installation. If it is  1-1/2 in (38 mm), an adapter ring is required.
   • Locate screws for step 3C and keep them within reach.
   • Install exterior keypad and mounting plate. Rotate the flat blade to a horizontal position to match the latch orientation. Support exterior assembly during mounting plate installation and make sure bolt is retracted. Cable goes underneath latch. The top of the mounting plate should be visible and kept parallel to edge of door. Tighten screws evenly, but do not over-tighten screws. Make sure the flat blade is centered in the mounting plate hole.
4. Programming:
   • Follow the instructions in the user manual to program the lock with a new user code and to test the lock.

Parts in the box

Required tools

Additional Tools (depending on the application)

Prepare the door and check the dimensions

If drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep

1. Measure to confirm that the hole in the door is either 2-1/8 in (54 mm) or 1-1/2 in (38 mm).
   Note : Additional door preparation may be required for doors with 1-1/2 in (38 mm) holes. Consult the deadbolt drilling instructions at www.kwikset.com/doorprep.

2. Measure to confirm that the backset is either 2-3/8 or 2-3/4 in (60 or 70 mm).

3. Measure to confirm that the hole in the door edge is 1 in (25 mm).

4. Measure to confirm that the door is between 1-3/8 and 1-3/4 in (35 mm and 44 mm) thick.
   Note : Please contact customer service if door thickness exceeds 1-3/4 in for a thick door kit.

Install the latch and strike

• Hold the latch in front of the door hole, with the latch face flush against the door edge.
• Is the door edge chiselled?
• Install strike on the door frame.
• IMPORTANT : Make sure the latch bolt is fully retracted (in the unlocked position).

Install the exterior keypad

What is the diameter of the hole in the door?

Locate screws for step 3C and keep them within reach

Install exterior keypad and mounting plate

Install the interior assembly

Remove interior cover from interior assembly

Secure the interior assembly onto the mounting plate

Install the batteries in the interior assembly

Install 4 AA batteries in interior assembly

Install interior cover for the interior assembly

Add user codes (25 max)

• Make sure the interior cover is off. Press the Program button once.
• Press number 1.
• Press Kwikset logo once.
• Enter user code. A total of 25 user codes may be programmed. User codes should be 4 to 8 digits in length.
• Press Kwikset logo once.
  During programming, if no button is pressed within 5 seconds, the system will time out and you will need to restart the procedure
  For security reasons, the first 4 digits of each User Code must be unique. For example, you are unable to program a user code 1-2-3-4-5 as well as user code 1-2-3-4-6.
  Note : After the first User Code is created, the latch bolt will automatically retract and extend to learn the locking and unlocking direction of the door. The Kwikset logo will indicate success or failure. GREEN: Success RED: Unsuccessful

Test the lock (review normal operation)

Before you can lock and unlock the door, a User Code must be created. Refer to Step 6 for instructions how to create a User Code. Confirm that the code(s) added in previous step can unlock the door.

1. To lock your door, press the Kwikset logo button. The lock will beep twice and the Kwikset logo button will flash amber as the deadbolt extends.
2. To unlock your door, enter the user code. The lock will beep twice and the Kwikset logo button will flash green as the deadbolt retracts.

Adding a One-time User Code

Delete a Single User Code

Delete ALL User Codes

Enable/ Disable Audio

Enable/ Disable User Codes

Note : When all User Codes are disabled, all electronic functions will be disabled as well. The door must be locked or unlocked manually with the key. Repeat the programming steps to enable the User Codes.

Enable/ Disable Auto-Lock

Change Auto-Lock Time Delay

Door Rehanding

The latch bolt will extend and retract to learn the orientation of the door.
Note : Perform this process for the lock to learn the locking and unlocking direction of the door. This feature is used for the lock to learn the orientation of your door (left- or right-handed). If stuck/jammed bolt error continues to occur after performing this step, please make sure there is no obstruction from strike or door jamb to prevent the bolt from extending.

Factory Reset

SmartKey Re-Keying
Re-key the lock to work with your existing kw1 key. See the supplied SmartKey Re-key instructions for more information.
Note : If Auto-Lock is enabled remove batteries before re-keying your lock.

Add/ Change Programming Code

Enable/ Disable Programming Code:

Optional : A Programming Code enables you to make programming changes without needing to access the Programming Button. This is ideal for landlords to program the lock without access to the interior programming button.
Note : Once Programming Code is enabled, the Programming Button is disabled and can only be used to factory reset the lock.
One Programming Code between 4 to 8 digits can be saved and cannot be the same as any User Code and cannot be used as a User Code to unlock the lock.

To program the lock with Programming Code:

Powerbolt at a Glance

System Alerts

Important Safeguards

1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Always have access to your lock’s standard key.
5. If using the Auto-Lock features, make sure you have your standard key with you to prevent locking yourself out.
6. Familiarize yourself with the system alerts.
7. Replace low batteries immediately.
8. Dispose of used batteries according to local laws and regulations..

CAUTION:
This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional

WARNING

Prevent unauthorized entry. Since anyone with access to the back panel can change the User Codes, you must restrict access to the back panel and routinely check the User Codes to ensure they have not been altered without your knowledge. The use of a programming code can help protect your system’s settings.

© 2022 Spectrum Brands, Inc.
Kwikset Technical Support
1-800-327-5625
www.kwikset.com

References

• Door Locks, Door Hardware, Smart Locks & Smartkey Technology | Kwikset
• Drilling Instructions | Kwikset

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>