CYGNETT Race Pro 10W Wireless Charger Vent Mount User Manual
- June 5, 2024
- CYGNETT
Table of Contents
CYGNETT Race Pro 10W Wireless Charger Vent Mount
Installation Instructions
Vent Mounting
Attach the product to your vent by pushing the spring-loaded clip (A) arnd
hook it onto the back of the vent blades in your vehicle. Once hooked on,
release the spring-loaded clip to grip onto the vent.
Adjusting the viewing angle
Adjust the angle by loosening the tightening ring (B) of the ball joint on the
back of the product. Once you are happy with the viewing angle, tighten the
ring (B) to hold in place.
Connecting the power source
Take the included USB-C to USB-A cable and connect it to the USB-C input (C)
of the wireless charger. Plug the USB-A end into the 12V USB Car Adapter and
plug into your vehicle’s 12V power sOcket.
Applying the magnets
With your device placed face down (without or without a case) on a flat
surtace, align the stencil’s indicated centre to your devices centre. Apply
the magnets in the stencil’s cut-Outs, then press and hold firmly for 30
seconds. Alternatively, place the larger set of magnets between your case and
device on the top and bottom half of your device.
Charge your device wirelessly
To wirelessly charge your device, place it over the wireless charging output
(D), making sure the magnets on your device are aligned with the magnetic
holders (E)
- A Spring-loaded clip
- B Adjustable ball joint for tightening ring
- C USB-C Input
- D Wireless charging output
- E Magnetic holders
Product Specifications
Troubleshooting
Not charging or slow charging
Please ensure you are using the supplied power adapter within the Race Pro
wireless charger. Using other chargers may result in slow charging or no
charge at all. If you need to replace the power adapter, please make sure it
supports QC 3.0 and supports a 12V USB output.
For optimum charge speed, adjust your device so that it is aligned to the centre of the wireless charging output (D). Please ensure that the case on your phone is not affecting the wireless charging by removing it and checking the performance. Some cases interfere with wireless charging if they contain metallic material or are overly thick.
Ensure that the magnets are not interfering with the wireless charging feature of your device, by allowing sufficient space from the centre of your device. Please note that this product may not be suitable for devices with central rear cameras or have large cameras which cover the area required for the magnetic plates.
Caution
- Do not disassemble or throw into fire or water.
- Do not expose to extreme weather conditions.
- Do not place close to a magnetic strip or strip card as it cOuld cause magnetic failure.
- Please keep charger a safe distance of at least 80cm from any implantable medical devices to avoid medical device interterence.
- This is not a toy and should be kept away from children.
- In the case of the device overheating. please disconnect immediately.
Please note that changes or modifications not expressly approved by the party
responsible for compliance could Void the users authority to operate the
equipment
Cygnett takes no responsibility for damages caused by incorrect use of its
products. Made in China.
This symbol on the product indicates that this product shall not be treated as
household waste. Instead it shall be sent to the applicable collection point
for the recycling
of electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment and
human health. For more information about the recycling of this product, please
contact your local city office.
Australian Consumer Law
Our goods come with guarantees that cannot bee excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure.
Cygnett warrants this product against defects in Workmanship and material for
a period of two (2) years from its original purchase date. You must present
your receipt as proof of date of purchase for warranty validation. Please read
the following information caretullyand retain this fo any warranty claim.
Terms & Conditions
- This product is for household use only. If the product is used in a commercial environment, the warranty period will be automatically reduced to three (3) months.
- Cygnett warrants that, with normal use or service, the product will be free from faulty parts, manufacture or workmanship.
- The warranty does not apply where damage is caused by other factors, eg. mishandling, abuse, accident or failure to follow operating instructions.
FCC Rules
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) the device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. The equipment generations, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. It this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to connect the
interference by one or more of the following measures:
- Reorient or relocate the receving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circut different from that to which the receiver is Connected.
- Consult the dealer or an experienced radio/TV technician for help
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exp0sure limits set forth for an
uncontrolled environment. The equipment should be installed and operated with
a minimum distance 0Ocm between the radiator and your body. The transmitter
must not be co-located or operating in conjunction With any other antenna or
transmitter.
Cygnett and the Cygnett logo are trademarks of Cygnett Pty Ltd. Other brands
and product names are trademarks or registered trademarks of their respective
holders.
2020 Cygnett PTY LTD.
Cygnett Head Office
858 Lorimer Street, Port Melbourne Victoria, 3207, Australia
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>