CYGNETT V-PRO 12 inch LED Ring Light User Manual
- June 6, 2024
- CYGNETT
Table of Contents
- CYGNETT V-PRO 12 inch LED Ring Light User Manual
- Caution
- Australian Consumer Law
- Installation
- Bluetooth Instructions
- Colour Modes
- Product Specifications
- Reorient or relocate the receiving antenna.
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CYGNETT V-PRO 12 inch LED Ring Light User Manual
Caution
Please read all warnings for your safety and optimal user experience. Please read and follow these instructions carefully and retain for your records.
- Do not disassemble or throw into fire or water.
- Do not expose to extreme weather conditions.
- This is not a toy and should be kept away from children.
- In the case of the device overheating, please disconnect immediately.
Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Cygnett takes no responsibility for damages caused by incorrect use of its products. Made in China.
This symbol on the product indicates that this product shall not be treated as household waste. Instead it shall be sent to the applicable collection point for the recycling of electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. For more information about the recycling of this product, please contact your local city office.
Australian Consumer Law
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Cygnett warrants this product against defects in workmanship and material for a period of two (2) years from its original purchase date. You must present your receipt as proof of date of purchase for warranty validation. Please read the following information carefully and retain this for any warranty claim.
Terms & Conditions
- This product is for household use only. If the product is used in a commercial environment, the warranty period will be automatically reduced to three (3) months.
- Cygnett warrants that, with normal use or service, the product will be free from faulty parts, manufacture or workmanship.
- The warranty does not apply where damage is caused by other factors, e.g. mishandling, abuse, accident or failure to follow operating instructions.
WARNING: KEEP BATTERIES OUT OF REACH OF CHILDREN.
Swallowing may lead to serious injury in as little as 2 hours or death, due to
chemical burns and potential perforation of the oesophagus. If you suspect
your child has swallowed or inserted a button battery immediately call the
24-hour Poisons Information Centre on 13 11 26 for fast, expert advice.
Examine devices and make sure the battery compartment is correctly secured,
e.g. that the screw or other mechanical fastener is tightened. Do not use if
compartment is not secure. Dispose of used button batteries immediately and
safely. Flat batteries can still be dangerous
Cygnett and the Cygnett logo are trademarks of Cygnett Pty Ltd. Other brands
and product names are trademarks or registered trademarks of their respective
holders.
© 2020 Cygnett PTY LTD. Cygnett Head Office 858 Lorimer Street, Port Melbourne
Victoria, 3207, Australia.
A LED ring light
B Device holder
C Pan/tilt ball joint
D Locking ring
E Metal tripod stand
F LED ring light controller
G Increase brightness
H Colour mode switch
I Decrease brightness
J Power button
Installation
- Untighten the locking ring (D) and open up the metal tripod stand (E).
- Tighten the locking ring (D) at the desired position.
- Install the pan/tilt ball joint (C) onto the stand.
- Install the LED ring light (A) onto the pan/tilt ball joint (C).
- Install the device holder (B) onto the LED ring light (A).
- Connect the LED ring light controller’s (F) USB-A end into a compatible USB-A wall charger. For optimal user experience, use a wall charger that supports up to 10W on a 5V supply.
- Press the power button (J) to turn on the LED ring light. A 1/4” thread adapter has been included. Swap this out with the device holder (B) should you wish to install a camera within the LED ring light.
Bluetooth Instructions
Turn on the Bluetooth remote by switching the button on the side of the remote
to ‘ON’. Go into your device’s Bluetooth settings and connect to ‘Cygnett BT’.
Use the corresponding shutter button on the remote to take
an image whilst in your camera app. Compatible with Android 4.2.2 OS or newer,
and iOS 6.0 or newer.
Colour Modes
The LED ring light has three different colour temperatures: warm white, neutral white and cool white. Change between these modes by pressing the colour mode switch (H).
Brightness Levels
To increase the brightness of the LED ring light, press the increase brightness button (G) on the remote. To decrease the brightness of the LED ring light, press the decrease brightness button (I) on the remote.
Product Specifications
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generations, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to connect the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>