Schlage Accents FA360/FA362/FA393 Installation Manual

Installation Instructions

FA360/FA362/FA393

Tools for Door Prep

2¹⁄₈” or 1¹⁄₂” hole saw

Drill bits: 1″, ⁷⁄₈”, ³⁄₈” ¹⁄₈”

Pencil and Chisel

Tools for Install

Phillips Screwdriver

Flat Head Screwdriver

• For FA360 and FA362 ONLY

A. Deadbolt Assembly

B. Deadbolt

C. Thumbturn Housing

D. Housing Screws (2)

E. Thumbturn Rose

F. Thumbturn

G. Handleset

H. Latch

J. Latch/Strike Screws (8)

K. Chassis

L. Chassis Screws (2)

M. Rose

N. Lever/Knob

P. Washer

Q. Handleset Screw

R. Screw Cover

S. Dummy Housing

T. Dummy Rose

U. Spin Ring

V. Inside Cylinder

W. Deadbolt Screws (2)

X. Cylinder Cover

Y. Push Pin

Z. Latch Strike

AA. Deadbolt Strike

BB. Dust Box

CC. Reinforcement Screws

DD. Reinforcement Strike

Door Preparation

A. Mark Centerline of Handleset

Mark centerline of handleset on both door faces and door edge.

B. Mark Trim Drill Points

a. Stand so door swings towards you.

b. Align template on centerline and fold template as shown.

c. Select backset. Mark drill points.

C. Drill Holes in Door Face

NOTE: Drill through-holes from both sides of door to avoid splintering wood.

a. For deadbolt and lockset, drill through holes as shown.

b. Drill bottom ³⁄₈” (10 mm) hole through door.

Door Prep for FA393 Dummy Trim Complete. MOVE TO STEP 3

D. Drill Door Edge Holes

a. For standard deadbolt, drill ⁷⁄₈” (22 mm) hole, 3¹⁄₈” (79 mm) deep. For drive-in deadbolt, drill 1″ (25 mm) hole, 3¹⁄₈” deep.

b. For standard latch, drill ⁷⁄₈” (22 mm) hole. For drive-in latch, drill 1″ (25 mm) hole.

c. For standard latch and deadbolt ONLY, drill ¹⁄₈” pilot holes for latch and deadbolt screws.

E. Mortise for Latch and Deadbolt

NOTE: No mortise needed for circular drive-in latch.

Use deadbolt or latch faceplate as a pattern for mortise. (Faceplate should fit flush.)

F. Prepare Door Jamb

a. Drill holes as shown and remove excess material from sides.

b. Mortise cutouts for strikes. Use strikes as patterns for mortises. (Strikes should fit flush with door jamb.)

c. Mark and drill pilot holes as shown.

Lock Installation

1. Select Latch/Deadbolt Faceplate

NOTE: If using square corner faceplate, move to STEP 2.

a. Use a screwdriver to separate the faceplate from the backplate as shown.

FOR ROUNDED CORNER FACEPLATE:

b. Snap rounded corner faceplate onto latch or deadbolt.

FOR CIRCULAR DRIVE-IN:

c. Rotate and remove backplate. d. Align grooves in faceplate with grooves on plastic collar. Snap collar around faceplate.

2. Install Latch and Deadbolt

a. Install deadbolt with the word “TOP” facing upward.

b. Secure latch and deadbolt with two (2) latch/strike screws OR for circular drive-in, use a wood block and hammer to tap latch and deadbolt flush.

3. Remove Knob/Lever, Thumbturn and Rose/Escutcheon

a. Remove knob/lever by pushing pin into hole and pulling knob/lever off. If needed, repeat for thumbturn.

b. Remove rose/escutcheon from chassis.

4. Install Handleset

NOTE: If installing one-piece escutcheon trim, follow steps 4 and 7 at the same time.

a. Rotate spindle so spindle base is closest to latch (reference printed label on chassis).

b. Insert spindle through latch and slide handleset into door.

c. Adjust screw post and insert into bottom hole.

NOTE: Hold handleset in place through steps 5 and 6.

5. Determine Door Handing

a. Stand on outside of door (side with handlset).

b. If hinges are on the left, door is a left hand door.

c. If hinges are on the right, door is a right hand door

6. Install Chassis

a. FOR LEVER ONLY: Rotate driver until tabs are aligned as shown for either right or left hand door.

b. Rotate chassis so knob/lever catch faces AWAY from latch.

c. Align holes in chassis with posts on handleset and slide chassis into door. d. Insert screws into holes in chassis and tighten.

7. Install Deadbolt Assembly

a. If using 1¹⁄₂” (38 mm) hole, pry adapter ring from assembly.

b. FOR FA360/FA362: Ensure pin is positioned to slide through correct backset slot in latch.

c. Insert assembly into door. Driver bar should slide under latch.

8. FOR FA360/FA393: Install Top Inside Trim

a. Slide housing into door so housing tab inserts into outside cylinder groove.

b. Insert two (2) screws and tighten.

c. Snap rose onto housing OR place escutcheon over housing.

d. FOR FA360 ONLY: Slide thumbturn onto actuator until it “clicks” into place.

OR FOR FA362: Install Top Inside Trim

a. Slide inside cylinder through spin ring OR escutcheon.

b. Slide cylinder into door so cylinder tab inserts into outside cylinder groove.

c. Insert two (2) screws into cylinder and tighten.

d. Snap cylinder cover into place.

9. Install Rose and Knob/Lever

a. FOR LEVER ONLY: Some packages include two levers. Use lever that matches “Correct” drawing.

b. FOR NON-ESCUTCHEON TRIM ONLY: Slide rose over spindle and snap onto chassis.

c. Slide knob/lever onto spindle until it “clicks” into place.

d. FOR LEVER ONLY: Check function. Thumbpiece should retract latch without turning lever. If function is incorrect, check steps 4 and 6.

10. Install Handleset Screw

NOTE: Adjust handleset so it is straight BEFORE tightening screws.

a. Insert mounting screw through washer and into screw post. Tighten.

b. Snap screw cover in place.

11. Install Escutcheon Screw(s) (if Necessary)

a. Adjust escutcheon so it is straight BEFORE installing screw(s).

b. Drill ¹⁄₈” (3 mm) pilot hole(s) through escutcheon screw hole(s) and into door as shown.

c. Insert screw(s) and tighten into door.

12. Install Strikes

Install as shown. Ensure deadbolt strike is installed in correct order.

Cylinder Cover Removal for FA362 ONLY

If Needed, Remove Cylinder Cover Insert screwdriver into keyway and carefully pry cover off.

Schlage Accents FA360/FA362/FA393 Installation Manual – Original PDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>