FALCON RIDGE AC-PROWLER-WTC01 Arctic Cat Prowler Windshield Top Combo Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instruction Manual
AC-PROWLER-WTC01 Arctic Cat Prowler Windshield Top Combo
Instructions for Installation and Care of Arctic Cat Prowler Windshield Top
Combo
Notice: Do not smoke inside the cab or expose the enclosure to direct
flames. The cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing
the enclosure. The installation is best done when the temperature is 70
degrees F. or warmer. The temperature affects the adhesive Velcro, if
conditions prevent installing in warmer weather it helps to store the adhesive
Velcro at room temperature prior to installation.
- Carefully unroll the Cab Enclosure on a large flat surface that is clean and free of dirt or other material that may soil or scratch the windows of the Cab. Next, Open the hood compartment and raise the bed. This will allow access to the front and rear to install the necessary Velcro pieces.
- Check over the parts included in the carton with the parts list shown below:
Self-Adhesive Velcro Hook strips:| 4 each| 10” long
---|---|---
“ “| 2 each| 24” long
“ “| 2 each| 6” long
Cab Enclosure| 1 each|
If any parts are damaged or missing please contact customer service at 606-845-7439.
- Loosely drape the Cab Enclosure over the Prowler roll cage, making sure to pass the rear brake light through the hole in the rear of the enclosure. Note the correct position for the 24″ Velcro Hook strips along the bottom of the Windshield. Clean the area with Isopropyl alcohol let it dry and apply the Velcro hook strip. The Velcro strips should be along the area that is under the Hood when it is closed.
- Working your way to the rear of the roll cage carefully fit the Cab into position. Pull down in the corner to approximate the position for the 12″ Velcro strip and wrap it around the roll cage. Now pull down on the corner and wrap adhesive Velcro with the double-sided strip sewn to the top.
- Take note of the position of the two 10″ Loop Tabs that are on both sides of the windshield. Apply the corresponding Velcro hook strips to these locations. Making sure to clean the area first.
- Now close the front hood and secure it down. It should sit on top of the bottom of the windshield.
Cleaning and Storage Recommendations:
- Before removing the Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll it for storage.
- It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory. On a large, clean, and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter. Put the rolled Cab back into the carton for storage at normal room temperature. It is best not to expose the Cab to either extremely hot or cold temperatures when storing.
- A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if the additional hook and loop sets are needed, they can also be ordered.
Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from the date the item is received. You MUST package the product
exactly as it was originally packaged from the factory to get a full refund
for the product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes. Lay all the windows on top of each other with the canvas
folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory-new condition to receive a refund – a
25% restocking fee will apply.
If ordered from Falcon Ridge please call
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is defective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridge’s many distributors’, you must first call them and
see what their return policy is. Once your item reaches our production
facility, our customer satisfaction team will inspect your item to ensure
unused, factory-new condition.
NOTE: All windshields must be returned with the original protective film
intact and not removed. Do NOT REMOVE it if you have any intentions of
returning the item. Refund/ replacement of a windshield will only be processed
on items with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered, or damaged in any way will not be subject for a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, the credit will be issued to
the original credit card/ payment method used for the purchase. Outbound
shipping and return shipping costs will not be refunded. Please allow 4 to 6
weeks for your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure,
tops, and/or windshield due to defects in the product. Please refer to the
return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase.