FALCON RIDGE Mid Size Polaris Ranger Full Enclosure Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
FALCON RIDGE Mid Size Polaris Ranger Full Enclosure
Instructions for Installation and Care of Ranger 400 Full Cab Enclosure w/
Lexann
PO-10MIDRANGER-FC03
Instructions for Installation and Care
CAUTION: Do not smoke inside the cab or expose the enclosure to direct
flames. Product is FLAMMABLE.
Be sure to read these instructions thoroughly before opening and installing
the enclosure.
The installation is best done when ambient temperature is 70°F or warmer. If installed in cold weather, warming the adhesive Velcro strips before installation is recommended.
-
Carefully open the carton and unroll the enclosure onto a large flat surface that is clean and free of dirt or other material that may soil or scratch the vinyl windows.
-
It will help to raise the bed prior to installing the cab enclosure.
-
Check over the parts included in the carton with the parts list shown below:Velcro hook strips 4 each 10” long
Velcro hook strips 10 each 3” long
Velcro hook strips 10 each 3” long
Velcro hook strips 2 each 12” long
Snap studs 15eac(1 extra)
Cab enclosure 1 each -
There are two components to this cab enclosure, the windshield and the soft enclosure. The enclosure will go over the top of the windshield across the visor and will attach to the roll cage under the windshield down the sides. It works best to install the cab enclosure first to get all of the Velcro in place and then remove it. Then install the windshield and reinstall the cab over top and under the windshield. To install the Lexan windshield, refer to the separate instructions provided.
-
Begin by raising the bed of the Ranger; clean the chassisbehind the cab with rubbing alcohol, and affix the 55” adhesive Velcro stripas illustrated in fig. A. Now place the cab enclosure on the Ranger; from the front walk it up and over to get it onto the roll cage. Once it is on, zip up the doors and make sure that the cab is centered and in place.
-
Now start in the rear and pull the Velcro down and attach it to the adhesive strip you have placed along the rear. It should reach to the bottom and be centered; you may have to detach and reattach until it is where you want it to be.
-
With assistance, pull the front sides of the cab down and wrap the Velcro tabs around the roll cage and ensure the bottom front with the snaps are in the right place to wrap around the fender and snap just inside the fender well. Mark the locations of the sewn-on Velcro tabs, andrefer to fig. B to apply the corresponding adhesive strips to the front downtubes.
Finish by attaching the Velcro tabs on the enclosure to their respective adhesive strips on the downtubes on both sides of the vehicle.
-
Now install the snaps along the inside of the fenders to match up with the snaps on the cab enclosure and you are ready to go. The photos below will help show you where the snaps go.
-
Now remove the cab and install the Lexan windshield according to the separate instructions provided.
-
Now to reinstall the cab enclosure, remove the two bottom clamps on the windshield so that you can raise it up and fit the Velcro tabs sewn onto the doors through to the adhesive sections on the roll cage. Now fit the enclosure up and over the top of the roll cage and pull it down and reattach all of the Velcro and snaps to line everything up correctly. Lifting up on the windshield slip the tabs through and attach and reinstall the lower clamps; slide them up under the front of the enclosure and around the roll cage.
-
All that remains is to attach the small Lexan brace across the top of the windshield. You will have to cut small slits through the material to allow the bolts through and sandwich the fabric between the windshield and brace. Refer to the diagrams in the separate instructions for installing the Lexan windshield. Congratulations! You have now finished the installation process.
Cleaning and Storage Recommendations
- Before removing the enclosure for storage, make sure it is clean and dry, to prevent soiling the textile and scratching the clear vinyl windows. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Let the enclosure dry thoroughly before attempting to roll for storage.
- It is important that the enclosure be rolled up for storage rather than folding. Folding will cause undesirable creasing of both the enclosure textile and the clear vinyl windows. Carefully roll up the enclosure similar to the way it was when it was packed at the factory. Put the rolled enclosure back into the carton for storage at a normal room temperature. It is best not to expose the enclosure to either extreme hot or cold temperatures when storing.
- A special cleaner/conditioner is available from Falcon Ridge that will greatly increase the service life of the cab enclosure. If needed, additional hook and loop sets are available, as well as other spare parts and hardware. Contact Falcon Ridge for information.
- Transporting or trailering your UTV with the enclosure installed is not generally recommended. It is best to remove the enclosure before transporting your UTV.
Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within 30 days from date item is received. You MUST package the product exactly as it was originally packaged from the factory to get a full refund for the product!
The vinyl windows should never be folded when packaging in the box or for storage purposes.
Lay all the windows on top of each other with the canvas folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production facility and must be in unused, factory new condition to receive refund – a 25% restocking fee will apply.
If ordered from Falcon Ridge please call at
606-845-7439 to gain a return
authorization number,
use our preferred shipping carrier (UPS) to return the item (unless the item
is defective, you are responsible for paying the shipping to return the item.)
Any returns submitted to Falcon Ridge without a return authorization number
will be charged a 20% restocking fee. If ordered from one of Falcon Ridges
many distributors’, you must first call them and see what their return policy
is. Once your item reaches our production facility, our customer satisfaction
team will inspect your item to ensure unused, factory new condition. NOTE:
All windshields must be returned with the original protective film intact and
not removed. Do NOT REMOVE if you have any intentions of returning the item.
Refund/ replacement of a windshield will only be processed on items with
original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered or damaged in any way will not be subject for a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved.
Once returned items are received, credit will be issued to the original credit
card/ payment method used for the purchase. Outbound shipping and return
shipping cost will not be refunded. Please allow 4 to 6 weeks for your refund
to be processed.
Warranty
To The Owner of this Product: Thank you for purchasing one of Falcon Ridge Cab Enclosures, Tops &/or Windshields! Below are the terms under which your product is covered under our manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure, tops and/or windshield due to defect of the product. Please refer to the return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this time frame we will gladly correct the problem or replace the enclosure, tops &/or windshield. Upon submitting for the correction or replacement we will need to receive pictures of the defect in material or workmanship along with the receipt from the date of purchase.
Thank you,
Falcon Ridge
Documents / Resources
|
FALCON RIDGE Mid Size Polaris Ranger Full
Enclosure
[pdf] Instruction Manual
Mid Size Polaris Ranger Full Enclosure, Ranger Full Enclosure, Mid Size
Polaris Full Enclosure, Full Enclosure, Enclosure
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>