FALCON RIDGE HO-PIONEER700-DRW01 Soft Doors Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of Honda Pioneer 700
Soft Door Rear Window Combo
HO-PIONEER700-DRW01
CAUTION: Do not smoke inside the cab or expose the enclosure to direct flames. Product is FLAMMABLE.
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is best done when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if conditions prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature prior to installation.
1. Carefully open the carton and roll out the enclosure on a large flat
surface that is clean and free of dirt or other material that may soil the
textile or scratch the clear vinyl windows of the enclosure.
2. Check over the parts included in the carton with the parts list shown
below:
Velcro hook strips 18 each 3” long
Velcro hook strips 2 each 9” long
Velcro hook strips 2 each 39” long
Velcro hook strips 1 each 19” long
Velcro hook strips 1 each 42” long
Screw snaps 3 each (1 extra)
Cab enclosure 3 Pieces
If any parts are damaged or missing please contact customer service at606-845-7439.
3. Begin by opening up the enclosure and with the help of another person
drape the enclosure over the roll cage and arrange into the correct position.
4. You will notice double-sided Velcro strips sewn to the cab enclosure.
At these locations, wrap the roll bar with one of the 3” adhesive Velcro
strips. After wrapping the Velcro around the bar wrap the double-sided strip
around the adhesive Velcro providing a very secure hold. The following
pictures show how this works.
- 3″ Adhesive Velcro
- Double-Sided Velcro
- Enclosure
5. After attaching the double-sided strips go to the rear of the door. You will see three Velcro tabs sewn here. Starting just below the top cross bar place the 32″ adhesive strips down the bar facing the rear of the vehicle. Then pull the tabs around and attach then down the bar to the Velcro. See Photos below.
6. Now move to the front lower corner and place the 9″ adhesive strip to match up with the Velcro on the cab. See Photo Below.
7. Last Item on the doors will be a snap on the inside front section of the plastic doors. Its easier to place the snap in the right position by first putting the screw snap stud into the socket on the enclosure. Then pull the door into place and push the snap into the plastic so that an mark is left. Then pull the snap out and screw it into the door making sure not to over tighten and strip out the plastic. See the following photos.
8. Begin the rear window by placing the 42″ adhesive Velcro strip across the top rear bar of the roll cage. This will hold the top of the rear window in place as shown in the photo below.
9. Next attach the sides to the double-sided velcro tabs sewn along the rear
of the doors.
10. Lastly place the 19″ Adhesive strip across the bottom to match up
with the Velcro sewn to the bottom of the Rear Window.
Cleaning and Storage Recommendations:
- Before removing the Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll for storage.
- It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory. On a large, clean and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter. Put the rolled Cab back into the carton for storage at a normal room temperature. It is best not to expose the Cab to either extreme hot or cold temperatures when storing.
- A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if additional hook and loop sets are needed, they can also be ordered.
Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within 30 days from date item is received. You MUST package the product exactly as it was originally packaged from the factory to get a full refund for the product!
The vinyl windows should never be folded when packaging in the box or for storage purposes. Lay all the windows on top of each other with the canvas folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production facility and must be in unused, factory new condition to receive refund – a 25% restocking fee will apply.
If ordered from Falcon Ridge please call at 606-845-7439 to gain a return authorization number, use our preferred shipping carrier (UPS) to return the item (unless the item is defective, you are responsible for paying the shipping to return the item.) Any returns submitted to Falcon Ridge without a return authorization number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors, you must first call them and see what their return policy is. Once your item reaches our production facility, our customer satisfaction team will inspect your item to ensure unused, factory new condition. NOTE: All windshields must be returned with the original protective film intact and not removed. Do NOT REMOVE if you have any intentions of returning the item. Refund/ replacement of a windshield will only be processed on items with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect them during transit and ensure your returned item arrives back factory fresh, and in new resalable condition ( any returned items that have been used, altered or damaged in any way will not be subject for a refund. ) All contents including instruction manuals, accessories, hardware, Velcro, etc. must be included in your return shipment. Only items in OEM factory new condition will be approved. Once returned items are received, credit will be issued to the original credit card/ payment method used for the purchase. Outbound shipping and return shipping cost will not be refunded. Please allow 4 to 6 weeks for your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or Windshields! Below are the terms under which your product is covered under our manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure, tops and/or windshield due to defect of the product. Please refer to the return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this time frame we will gladly correct the problem or replace the enclosure, tops &/or windshield. Upon submitting for the correction or replacement we will need to receive pictures of the defect in material or workmanship along with the receipt from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>