SCX Design W13/32486 Maple Wood 10W Wireless Charger Instruction Manual
- June 5, 2024
- SCX Design
Table of Contents
SCX Design
W13/32486 Maple Wood 10W Wireless Charger
Instruction Manual
SCX Design® Maple Wood 10W Wireless Charger
Reference W13/32486
Please read the instruction manual carefully before using the product.
Product Specifications
Material: ABS with soft-touch finish
Item dimension: ø68×10.2mm
Weight: 32g
Micro Input: 5V/2A, 9V/2A
Wireless output: DC 5V/1A, 9V/1.12A
Output: 10W
The product includes a micro USB charging cable.
Key functions
Functionalities
Connect the wireless charger the micro USB cable to the wireless charging pad
(A), and connect the USB to the USB port of your PC/laptop or charger.
Make sure your phone is compatible with wireless charging.
Put your wireless charging enabled device on the wireless charging surface (B)
Warning!
Some phone cases may block wireless charging. Do not place other materials
between the mobile device and the wireless charger pad.
Check your mobile device’s battery percentage using the charging icon
displayed on the screen of your phone.
When the mobile device is not placed on the charging surface accurately, your
mobile device may not charge properly. Please do not expose this device to
moisture or heat sources
Keep the product out of reach of children.
Using your phone while charging it can cause higher temperatures.
This product complies with European Directive 2002/96 / EC on waste electronic
and electronic equipment (WEEE) and 2011/65 / EU & 2015/863/EU on the use of
certain hazardous substances in electrical and electronic equipment (RoHS).
FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.
Never Store or use this product in temperatures below 32°F (0°C) or above
115°F (45°C).
SAFETY WARNING
In order to prevent conditions. that can lead to overheating, please make sure that the wireless charging pad surface is free of all metal objects at all times, such as coins or paper clips. In addition, before charging, please remove anything metallic attached to the back of the phone, such as battery cases, ring holders, or plates used for mounting to magnetic phone holders.
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC’s RF radiation exposure limits set forth for an
uncontrolled environment. A separation distance of 20 cm or more should be
maintained between this device and persons during device operation. To ensure
compliance, operation at closer to this distance is not recommended.
The antenna used for this transmitter must not be co-located in conjunction
with any other antenna or transmitter.
Imported by SCX Design
68 bis boulevard Pereire
75017 Paris
France
IMPORTER FOR USA AND CANADA
IMPORTATEUR POUR LES ETATS-UNIS
ET LE CANADA
Distributed by Koozie Group
14421 Myerlake Circle
Clearwater, FL 33760
USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>