SHURE Podcast Microphone MV7X User Guide

June 6, 2024
Shure

SHURE Logo

SHURE Podcast Microphone MV7X

SHURE Podcast Microphone MV7X

General Description

The Shure MV7X is a professional-quality dynamic microphone, ideal for close mic applications that require vocal intelligibility with a balanced tone. The attractive and durable all-metal design features an adjustable yoke that can be mounted onto a vari-ety of microphone stands for flexible placement options.

Features

Voice Isolation Technology

Highly directional cardioid pattern isolates your voice and removes unwanted background noise

Durable, Versatile Design

Rugged, all-metal construction and excellent cartridge protection for outstanding reliability

The MV7X features a dynamic capsule with a cardioid pattern, which uses Voice Isolation Technology to pick up sound directly in front of the microphone.

MV7X Output

MV7X Output

  • Passive XLR output: Connect to XLR mixers and interfaces.

Mounting Instructions

The MV7X microphone comes equipped with a 5/8″-27 threaded mount, the thread size most commonly found on microphone stands. This mount can be used with a microphone stand or hung from a boom.
Note: Be very careful not to unloosen the screws all the way.

Mounting Instructions

To easily flip the microphone orientation, loosen the screws and rotate 180 degrees.

Windscreen

The windscreen offers maximum protection from plosives and creates a warmer, more intimate sound for speech applications, like podcasting and gaming.

Specifications

  • Transducer Type
    • Dynamic (moving coil)
  • Polar Pattern
    • Unidirectional (Cardioid)
  • Output Impedance
    • 252 Ω
  • Frequency Response
    • 20 Hz to 20,000 Hz
  • Sensitivity (@ 1 kHz, open circuit voltage)
    • -55 dBV/Pa [1] (1.78 mV)
  • Polarity
    • Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3
  • Housing
    • All metal construction
  • Mounting Type
    • 5/8-27 thread mount
  • Net Weight
    • 0.55 kg (1.21 lbs)

[1] 1 Pa=94 dB SPL

Typical Frequency Response Typical Frequency Response

Typical Polar Pattern

Typical Polar Pattern

Overall Dimensions Overall Dimensions

MV7X Yoke Assembly

The MV7X yoke allows a podcaster to be flexible with mic placement. Loosen the yoke knobs and you can adjust the micro-phone in a variety angles. If the microphone becomes detached from the yoke, these are the steps to put it together in the cor-rect order to ensure that your microphone is secure. Each side uses one thin gray spring washer, one shiny silver brass washer, two black plastic washers and the yoke and threaded yoke knob.

MV7X Yoke Assembly 01

  1. Start with the threaded knob flat side down on your tabletop.
    MV7X Yoke Assembly 02

  2. Stack the washers on the threaded knob.

    • Place a black plastic washer on the knob.
    • Place one side of the yoke on next.
    • Then put the second black plastic washer on.
    • Place the flat silver washer and then the thin spring washer on the threaded knob.
  3. Using your finger to hold the screw assembly in place, slide the MV7X onto the threaded screw and turn the knob to keep washers in place.
    Note: Be sure to keep this side on but loose so that you have room to easily move the yoke and assemble the washers on the opposite side.

  4. On the opposite yoke arm, place the washers into the side of the MV7X in reverse order. Thin spring washer > Flat silver washer > Black plastic washer > Yoke arm

  5. The yoke arm needs to be placed directly onto the stack of washers. To ensure that the washers are aligned, put a pen through the yoke and washers to make sure that everything is properly centered. Leave pen in place.

  6. Place the second black plastic washer onto the remaining threaded knob.

  7. Remove the pen. Insert the threaded knob and black plastic washer into the stacked washers and tighten both sides to ensure that your microphone is stable.
    MV7X Yoke Assembly 03

Accessories

Furnished Accessories
  • Brass Adapter – 31B1856
Replacement Parts
  • Black Windscreen – AMV7-K-WS

Certifications

This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Global Compliance
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Email: info@shure.de
www.shure.com

SHURE Logo

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals