Scx Design 32498 10000 mAh Jumbo Wireless Power Bank Instruction Manual
- June 5, 2024
- SCX Design
Table of Contents
Scx Design 32498 10000 mAh Jumbo Wireless Power Bank
Please read the instruction manual carefully before using the product.
Product Specifications
- 146 x 72 x 14 mm
- 222 gr
- Type-C Input: DC 5V/2A
- USB-A Output 2: DC 5V/2A
- Battery/Cell capacity: 37Wh, 3.7V/10.000mAh
- Product capacity(USB): 27.4Wh, 5V/5480mAh
- Wireless output: 5V/1A
- Product capacity (Wireless):21Wh, 5V/4200mAh
- Material: ABS with soft-touch finish
The product includes a 3-in-1 cable (iPhone, micro, type C).
Functionalities
Led indicator to show remaining power. Dual USB output ports for different devices. Multiple safety protection systems to ensure the safety of the devices: protection in the event of overload, overvoltage, overcurrent, and short circuit.
The remaining charge power is displayed by shaking the product. It can fully charge an iPhone, an Android device, or any other regular mobile phone once per load cycle.
- To charge your charger, connect the supplied cable to your wall charger or to a USB port on your computer. The USB connector goes to your charger, and the USB Type C port goes on this battery charger.
- To charge your phone or other mobile device plug the cable into the USB port of the charger with the other connector going to your device.
Wireless functionalities
- When the wireless power bank is fully charged, the light is always on.
- When the wireless power bank is charging or fully charged put your smartphone on the side with the wireless logo of the power bank to charge your smartphone wirelessly or charge your smartphone via the USB output with the provided 3-in-1 cable.
- When the wireless power bank is fully discharged, the blue LED light will be turned off.
Do not place or use this product near a source of high heat or in a humid environment. Do not use it if the equipment is damaged. Only use the cables that are supplied with this equipment. Keep the product out of reach of children. If the charger hasn’t been used for a long time, please charge/unload it once every 3 months to preserve the functionality of the product. Using your phone while charging it can cause high temperatures.
This product complies with the EMC Directive 2014/30/EU, the Low voltage directive 2014/35/EU, the RoHS Directive 2011/65EU, and its amendment directives 2015/863/EU and SVHC as listed in REACH registration. It also complies with the European Directive 2002/96/EC on waste electronic equipment (WEEE).
SAFETY WARNING
In order to prevent conditions. that can lead to overheating, please make sure that the wireless charging pad surface is free of all metal objects at all times, such as coins or paper clips. In addition, before charging, please remove anything metallic attached to the back of the phone, such as battery cases, ring holders, or plates used for mounting to magnetic phone holders.
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. A separation distance of 20 cm or more should be maintained between this device and persons during device operation. To ensure compliance, operation at closer to this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>