JOHN LEWIS Ahead Outdoor Wall Light User Guide
- June 6, 2024
- John Lewis
Table of Contents
AHEAD OUTDOOR WALL LIGHT
USER GUIDE
Introduction
Thank you for purchasing this Ahead outdoor wall light.
Please read the instructions carefully before use to ensure the safe and
satisfactory operation of this product.
Warnings
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work. It is
recommended that this fitting is installed by a qualified electrician.
Install in accordance with the IEE Wiring regulations and the Building
Regulations.
To prevent electric shock switch off at mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge.
If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a 5 amp fused circuit.
If replacing an existing fitting, make a note of the connections.
This product is rated IP44 and is suitable for outdoor use.
This product is suitable for installation on surfaces with normal flammability
e.g.
wood, plasterboard, masonry. It is not suitable for use on highly flammable
surfaces (e.g. polystyrene, textiles).
For your safety, always switch off the supply before changing lightbulbs,
cleaning or removing shades. Always take care when handling lightbulbs to
avoid injury in case of breakage.
| Parts list | Qty | |
|---|---|---|
| Light fitting (F) | 1 | |
| Shade (E) | | 1
Wall plugs| 
| 2
Screws| 
| 2
Recommended bulb
Recommended bulb (not included)
1 x 10W LED E27 GLS, or 1 x 40W (Max.) E27 GLS
When changing a bulb, always switch off at the mains and allow the bulb to
cool before handling. Dispose of used bulbs carefully. Do not exceed the rated
power stated or use a different shape bulb from that indicated on the
fitting.
Product assembly
-
Carefully unpack the carton, making sure all the parts are present before assembly.
Before removing the existing fitting, carefully note the position of each set of wires. -
Remove the backplate (A) from the fitting by removing finials (B).
Using the wall plugs and screws (C) provided in the fixing pack, secure the backplate to the wall. Take care to avoid damaging any concealed wiring and pipes.
Ensure drain hole (G) is at the base of the backplate.
-
Having identified the household wiring from your existing light fitting, connect to the outdoor-rated connection block (D) inside the product in the following way.
Check that: You have correctly identified the house wires.
• The connections are tight.
• No loose strands have been left out of the connection block.
• Ensure the grommet is in place to maintain IP rating.
-
Re-attach the light fitting to the back cover (A) by locating the screw holes over the screws and replacing the finials (B) and the rubber washers, tightening them securely.
Fit the recommended bulb.
Attach the shade (E) by screwing onto the light fitting (F).
Ensure shade is tightly fitted to compress the rubber seal but do not overtighten.
Caring for your product
Do not use solvents or abrasive cleaners as these could damage the finish.
In normal circumstances, stainless steel is very resistant to corrosion. It
does however require maintenance to preserve the high-quality appearance. Wash
the product with warm soapy water, removing all surface deposits. Rinse with
clean water and with a soft cloth, wipe dry. In some cases, surface corrosion
may arise after installation. This is normally caused by tiny iron particles
left behind after the brushing process when finishing. Wash and dry as
detailed above. Then with a soft cloth soaked with protective oil, wipe all
over.
However, if the product is subject to extreme environmental conditions such as
marine locations, industrial pollution, and acid rain these maintenance
procedures should be carried out around four times a year. For severe
corrosion, non-abrasive cream cleaners or proprietary stainless steel cleaners
should be used to remove the corrosion. Wash and dry as detailed above. Then
with a soft cloth soaked with protective oil, wipe all over.
Glass parts – Remove and wash in warm water or just use a damp cloth. Do not
use abrasive materials as these will damage the finish.
Aftercare and Troubleshooting
If you experience any unresolvable technical issues with the product, contact
your nearest John Lewis & Partners shop or John Lewis & Partner.
Technical Support on 03301 230106.
Specification
Max. power: 40W
Voltage: 220–240V, 50Hz
IP rating: 44
Weight: 0.814kg
5-year guarantee
At John Lewis & Partners we test every light to high-quality standards so we are able to offer you a 5 year guarantee.
Recycling
This symbol indicates that this product should not be treated as normal household waste and it should be recycled. John Lewis & Partners do not operate instore take back, but as members of the Distributor Take Back scheme have funded the development and upgrade of recycling facilities across the UK. Please take it to your nearest collection facility or for further details contact your local council or visit www.recycle-more.co.uk.
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
johnlewis.com
Made in China
Please retain these instructions for future reference.
25/11/2020
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>