Nedis SAMP40025WT | SAMP40045WT CATV Amplifier User Manual
- June 5, 2024
- nedis
Table of Contents
SAMP40025WT | SAMP40045WT CATV Amplifier
User Manual
Preface
Thank you for purchasing the Nedis SAMP40025WT/SAMP40045WT.
This document is the user manual and contains all the information for correct, efficient and safe use of the product.
This user manual is addressed to the end user. Read this information carefully before installing or using the product.
Always store this information with the product for use in the future.
Product description
Intended use
The Nedis SAMP40025WT / SAMP40045WT is an antenna signal amplifier intended to improve the signal for your tv.
The product is intended for indoor use only.
The product is not intended for professional use.
Any modification of the product may have consequences for safety, warranty and proper functioning.
Specifications
Product
|
CATV Amplifier
|
CATV Amplifier
---|---|---
Article number
|
SAMP40025WT
|
SAMP40045WT
Dimensions (l x w x h)
|
66 x 57.2 x 28 mm
|
102 x 57.2 x 28 mm
Frequency range
|
50 – 694 MHz
|
50 – 694 MHz
Gain
|
15 typ. 11.5 dB min.
|
10 typ. 6.5 dB min.
Gain control
|
12 dB min.
|
12 dB min.
Input return loss
|
8 typ. 5 dB min.
|
8 typ. 5 dB min.
Output return loss
|
8 typ. 5 dB min.
|
8 typ. 5 dB min.
Noise figure
|
5 typ. 8 dB min.
|
5 typ. 8 dB min.
Output level
|
85 dBµV min.
|
80 dBµV min.
Impedance
|
75 Ω
|
75 Ω
Input connector
|
IEC female x1
|
IEC female x1
Output connector
|
IEC male x2
|
IEC male x4
Power Adapter Input
|
100 – 240 VAC ; 50 / 60 Hz ; 0.15 A
|
100 – 240 VAC ; 50 / 60 Hz ; 0.15 A
Power Adapter Output
|
max. 5.0 VDC ; 1.0 A, 5.0 W
|
max. 5.0 VDC ; 1.0 A, 5.0 W
Main parts (image A)
A
1. Control screw
2. Power adapter connector
3. Input port
4. LED power indicator (on/off)
5. Output port
Safety instructions
WARNING
- Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep this document for future reference.
- Only use the product as described in this document.
- Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
- Do not expose the product to direct sunlight, naked flames or heat.
- Do not expose the product to water or moisture.
- Do not drop the product and avoid bumping.
- This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.
- Do not plug or unplug the power supply with wet hands.
- The mains plug is used as the disconnect device, such disconnect device shall remain readily operable.
- Risk of electric shock. The product should only be opened by an authorized technician when service is required.
- Disconnect the product from the power source and other equipment if problems occur.
Explanation of the symbols on the product or packaging
Icon
|
Description
---|---
|
Electronic equipment needs to bear the CE mark in order to be marketed in the EU. CE marking shows that a product is assessed before being placed on the market and that it meets EU safety, health and environmental protection requirements. CE marking is also sometimes accepted as a means of compliance with type-approval requirements; for example, electronic components that require type-approval and also CE marking for electromagnetic compatibility (EMC) or low-voltage equipment.
|
Indication that the producer of the packaging material complies with the Packaging Law and has contributed to the costs of the ‘Green Dot’ waste separation and recycling system.
|
Indication to explain that the product can be recycled.
|
Indication to explain that the product should be recycled appropriately.
|
This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.
Installation
- Check the contents of the package
- Check that all parts are present and that no damage is visible on the parts. If parts are missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.
Connecting the product
B
- See image B for a connection overview.
Mounting the product (optional)
C
- See image C for mounting instructions.
Use
Using the product
Turn the control screw A 1 using a flat-head screwdriver to control the amplification of the signal.
Maintenance
- Clean the product regularly with a soft, clean, dry cloth. Avoid abrasives that can damage the surface.
- Do not use aggressive chemical cleaning agents such as ammonia, acid or acetone when cleaning the product.
- Do not clean the inside of the product.
- Do not attempt to repair the product. If the product does not operate correctly, replace it with a new product.
Warranty
Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.
This product is designed for private use (normal domestic use) only. Nedis is not responsible for wear, defect and/or damages caused by commercial use of the product.
Disclaimer
Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.
Disposal
|
This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.
---|---