nedis WIFILOFC20FBK Smart WiFi Floodlight User Guide

: May 15, 2024
: nedis

Table of Contents

WIFILOFC20FBK Smart WiFi Floodlight
Smart WiFi Floodlight
Intended use
Specifications
Safety instructions
Install the mounting bracket
Installing the Nedis SmartLife app
Connecting the app
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Smart WiFi Floodlight
(with Sensor)
For outdoor use (IP65 / IP44)
WIFILOFC20FBK
WIFILOFS20FBKX Quick start guide

WIFILOFC20FBK Smart WiFi Floodlight

ned.is/wifilofc20fbk
ned.is/wifilofs20fbk http://ned.is/WIFILOFS20FBK nedis
WIFILOFC20FBK Smart WiFi Floodlight - Fig

Smart WiFi Floodlight

For more information see the extended manual online: ned.is/wifilofc20fbkned.is/wifilofs20fbk

Intended use

The Nedis Wi-Fi based Floodlight is used to illuminate indoor and outdoor areas.
This product is intended for indoor and outdoor use.
The product is not intended for professional use.
The product can be controlled with the Nedis SmartLife app.
Any modification of the product may have consequences for safety, warranty and proper functioning.

Specifications

Main parts (image A)

LEDS
PIR sensor*
Power cable
Mounting bracket bolts
Mounting bracket

WIFILOFS20FBK only.

Safety instructions

WARNING

Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep the packaging and this document for future reference.
Only use the product as described in this document.
Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
Do not drop the product and avoid bumping.
This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.
Disconnect the product from the power source and other equipment if problems occur.
Disconnect the product from the power source before service and when replacing parts.
Only use the provided power cable.
Do not unplug the product by pulling on the cable. Always grasp the plug and pull.
Children should be supervised to ensure that they do not play with the product.
Only power the product with the voltage corresponding to the markings on the product.
Do not look directly into the light, this may cause eye damage.
Some wireless products may interfere with implantable medical devices and other medical equipment, such as pacemakers, cochlear implants and hearing aids. Consult the manufacturer of your medical equipment for more information.
Do not use the product at locations where the use of wireless devices is prohibited due to potential interference with other electronic devices, which may cause safety hazards.

Install the mounting bracket

****Make sure the power cable is disconnected from the power outlet.

Check what plugs and screws are best suited for the intended surface.
**** The maximum diameter of A5 is 4.5 mm.
Remove the mounting bracket bolts A4 from the product.
Remove the mounting bracket A5 from the product.
Use A5 to mark the drill locations with a pencil.
Drill the holes.
Insert wall plugs.
Fasten A5 to the wall with screws.
Attach the product to A5 by fastening A4.

Installing the Nedis SmartLife app

Download the Nedis Smartlife app for Android or iOS on your phone via Google Play or the Apple App Store.
Open the Nedis Smartlife app on your phone.
Create an account with your e-mail address and tap Continue.
**** You will receive a verification code on your e-mail address.
Enter the received verification code.
Create a password and tap Done.
Tap Add Home to create a SmartLife Home.
Set your location, choose the rooms you want to connect with and tap Done.

Connecting the app

Make sure Bluetooth is enabled on your smartphone.
Open the Nedis Smartlife app on your smartphone.
Register or login to your account.
Tap + in the top right corner.
Insert the power plug into a power outlet.
Select the product type you want to add from the list.
The LEDs A1 blink to indicate pairing mode is active.
If the LEDs are not blinking, switch on the product, and after 10 seconds, switch the product off and on 3 times to manually enter the pairing mode.
Follow the instructions in the app.

PIR sensor control (WIFILOS20FBK only)
After connecting the device with the app, the control page opens automatically.

Tap on Sensor to enter the sensor control menu.
Switch the sensor on or off.
Set the detection distance.
Set the detection sensitivity.
Set the light duration after detection.

PIR sensor stand-by light (WIFILOS20FBK only)

Activate the Slight bright option in the sensor control menu
Set the stand-by light brightness.
Set the stand-by light duration.
**** The product enters stand-by mode after the full light duration.

Declaration of Conformity
We, Nedis B.V. declare as manufacturer that the product
WIFILOFC20FBK / WIFILOFS20FBK from our brand Nedis, produced in China, has been tested according to all relevant CE standards and regulations and that all tests have been passed successfully. This includes, but is not limited to the RED 2014/53/EU regulation.
The complete Declaration of Conformity (and the safety datasheet if applicable) can be found and downloaded via:
nedis.com/WIFILOFC20FBK#support
nedis.com/WIFILOFS20FBK#support

Nedis BV
De Tweeling 28, 5215 MC ’s-Hertogenbosch
The Netherlands