ACS ACR122U USB NFC Reader User Manual

June 5, 2024
ACS

ACS ACR122U USB NFC Reader

ACS ACR122U USB NFC Reader

Introduction

The ACR122U is a reader (IFD and PCD) reader which supports contactless (PICC) smart cards

Features

  • ISO 14443 Parts 1-4 Compliant for Contactless Smart Card Interface.
  • ISO 18092 Compliant for Contactless Smart Card Interface.
  • An external antenna for PICC contactless access applications.
  • Supports the following Tag Types:
    •  MIFARE Classic. E.g. MIFARE 1K, 4K, MINI and Ultralight.
    •  1S014443-4 Type A and B.
    • IS018092 FeliCa, NFC tag
  • T=CL emulation for MIFare 1K/4K PICCs
  • High Speed (424 kbps) Communication for PICCs
  • Energy saving modes for turning off the antenna field whenever the PlCC is inactive, or no PICC is found. It prevents the PICC from exposing to the field all the time.
  • User-Controllable Peripherals. E.g. LED.
  • PCSC Compliant for Contact and Contactless Interfaces.
  • USB V2.0 Interface. (12M bps)
  • Device Firmware Upgradeable through the USB Interface.

Architecture

  • GD32 is for main processor for communication with PC, and control the contactless chip and peripherals. PN532 acts as a contactless chip to perform the communication between contactless tags and GD32. ACS ACR122U USB NFC Reader 1
  • For communication architecture, the protocol between ACR122U and PC is using CCID protocol. All the communication between PICC is PCSC Compliant.ACS ACR122U USB NFC Reader 2

ACR122U Operating Procedure

Driver installation Procedure

  • Hardware requires:
    • ACR122U
    • PC with OS window XP or above
  • Software requires:
    • Driver installer “ACS_Unified_PCSC_Driver_Installer_bin-4.0.6.0-20141114_all.zip”

Steps:

  1. **** Extract the file “ACS_Unified_PCSC_Driver_Installer_bin-4.0.6.0-20141114_all.zip”
  2. Execute “Setup.exe”ACS ACR122U USB NFC Reader 3
  3. Below screen will be shown
  4. Below screen will be shown, “Next” to continueACS ACR122U USB NFC Reader 5
  5. Below screen will be shown, configure the installation path, then “Next” to continueACS ACR122U USB NFC Reader 6
  6. Below screen will be shown, “Install” to continueACS ACR122U USB NFC Reader 7
  7. Waiting until below screen shownACS ACR122U USB NFC Reader 8

Operation Example

Hardware requires:

  • ACR122U
  • PC with OS window XP or above
  • Test card x 1 (provided by ACS)

Software requires

  • APDU.exe (for example)

Steps:

  1. Plug in the reader into the PC
  2. Place the Test Card on the top of the reader about 5cm
  3. Open “APDU.exe”ACS ACR122U USB NFC Reader 9
  4. Click “1. Select reader”, Chose “ACS ACR122 0”, then click “OK”_ACS ACR122U USB NFC Reader 10
  5. Select “T1”, “Stress”, Message = “FF CA 00 00 00”, Interval = “500”ACS ACR122U USB NFC Reader 11
  6. Press “Connect”ACS ACR122U USB NFC Reader 11
  7. Press “Transmit” to start the testingACS ACR122U USB NFC Reader 13
  8. Below screen will be shown
  9. Can start the Lab Test

FCC Caution

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  •  This device may not cause harmful interference, and
  •  this device must acoept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can.be.determined by turning the equipment off and.on the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals