Nedis RFPS110WT | RFPSD110WT RF Smart Build-in Switch User Manual
- June 5, 2024
- nedis
Table of Contents
RFPS110WT RFPSD110WT RF Smart Build-in Switch
User Manual
Preface
Thank you for purchasing the Nedis RFPS110WT | RFPSD110WT.
This document is the user manual and contains all the information for correct, efficient and safe use of the product.
This user manual is addressed to the end user. Read this information carefully before installing or using the product.
Always store this information with the product for use in the future.
Product description
Intended use
The Nedis RFPS110WT | RFPSD110WT is a build-in adapter that allows you to control a connected device or light source.
Pair it with a Nedis RF Wall Switch or Nedis RF Smart Remote Control for wireless use (sold separately).
The product is intended for indoor, domestic use only.
Any modification of the product may have consequences for safety, warranty and proper functioning.
Specifications
Product
|
RF Smart Build-in Switch
|
RF Smart Build-in Switch
---|---|---
Article number
|
RFPS110WT
|
RFPSD110WT
Input voltage
|
250 V / 50 Hz
Plug
|
Installation wire terminal block
Maximum output power
|
2300 W
|
300 W
Dimming range
|
–
|
20 % – 80 %
Energy-saving
|
–
|
12 – 60 W
Frequency
|
433.92 MHz (±150k)
Range
|
30 m
Working temperature
|
-10 – 40 °C
Humidity
|
0 % – 80 %
Main parts (image A)
A
1. Status indicator LED
2. Power and reset button
3. Wire terminal (neutral)
4. Wire terminal (in)
5. Wire terminal (out)
6. Mounting wings
Safety instructions
WARNING
- Only use the product as described in this manual.
- Risk of electric shock. The product should only be opened by an authorized technician when service is required.
- Disconnect the product from the power outlet if a problem occurs.
- Do not use the product if a part is damaged or defective. Replace a damaged or defective device immediately.
- Read the manual carefully before use. Keep the manual for future reference.
- Do not stack the product.
- Do not drop the product and avoid bumping.
- Do not use the product in wet or damp environments.
- Do not expose the product to water or moisture.
Installation
- Check the contents of the package
- Check that all parts are present and that no damage is visible on the parts. If parts are missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.
Installing the product
- Keep a distance of at least 1 m between your Nedis RF Smart products.
1. Insert the mains phase wire into the wire terminal A 4.
2. Insert the switch wire from a device into A 5.
3. Insert the neutral wire into A 3.
4. Tighten the screws.
5. Place the product in a junction box.
- Make sure the power and reset button A 2 is accessible.
6. Insert screws through the mounting wings A 6 to fasten the product.
7. Press the power and reset button A 2 to switch the device on or off.
Setting the product to pairing mode ****
- You can pair the product with a Nedis RF Wall Switch or Nedis RF Remote Control for wireless use (sold separately).
- The product must be paired with a Nedis RF transmitter to access the dim function (RFPSD110WT only).
1. Hold the transmitter close to the product.
2. Press and hold A 2 until the status indicator LED A 1 flashes. The product is now in pairing mode.
3. On the transmitter, press an ON button to connect to the product.
- The product makes a clicking sound when successfully paired to a Nedis RF transmitter.
For more options:
- Follow the instructions in the manual of the Nedis RF transmitter.
Disconnecting a transmitter
1. Press and hold A 2 until A 1 flashes.
2. On the transmitter, press the OFF button of the paired channel. A 1 flashes twice.
Disconnecting all transmitters
1. Press and hold A 2 until A 1 flashes.
2. Release and press A 2 again. A 1 flashes twice.
Maintenance
1. Disconnect the product.
2. Clean the outside of the product using a soft, damp cloth.
- Do not clean the inside of the device.
- Do not use cleaning solvents or abrasives.
- Do not attempt to repair the product. If the product does not operate correctly, replace it with a new product.
Warranty
Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.
Disclaimer
Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.
Disposal
|
This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.
---|---
Declaration of Conformity
We, Nedis B.V. declare as manufacturer that the product RFPS110WT | RFPSD110WT from our brand Nedis®, produced in China, has been tested according to all relevant CE standards and regulations and that all tests have been passed successfully. This includes, but is not limited to the RED 2014/53/EU regulation.
The complete Declaration of Conformity (and the safety datasheet if applicable) can be found and downloaded via:
webshop.nedis.com/rfps110wt#support
webshop.nedis.com/rfpsd110wt#support
For additional information regarding the compliance, contact the customer service:
Web: www.nedis.com
E-mail: service@nedis.com
Phone: +31 (0)73-5991055 (during office hours)
Nedis B.V., de Tweeling 28
5215 MC ’s-Hertogenbosch, the Netherlands
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>