iskydance SS-B(WZ) ZigBee RF Smart AC Switch User Manual
- June 5, 2024
- iskydance
Table of Contents
iskydance SS-B(WZ) ZigBee RF Smart AC Switch
Tuya APP cloud control/Philips HUE control/Voice control/RF AC Switch/Push onoff/Wall junction box mounting
Features
- ZigBee + RF + AC push smart switch, without dimming function.
- To switch single color LED lamps, traditional incandescent and halogen lights.
- Tuya APP cloud control, support on/off, delay turn on/off light and timer run function.
- Philips HUE APP control by connect with Philips HUE bridge.
- Voice control, support amazon ECHO and TmallGenie smart speaker.
- Compatibility with RF 2.4G dimming remote control.
- Connect with external push switch optional.
- Easy to be placed in standard wall junction box behind a push switch.
- Over-heat / Over-load protection, recover automatically.
Technical Parameters
Input and Output
Input voltage| AC100-240V
Output voltage| AC100-240V
Output current| Max 1.5A
Output power| 150-360W
Input signal| Tuya APP + RF + Push switch
RF Control distance| 30m(Barrier-free space)
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED
Weight
Net weight| 0.041kg
Gross weight| 0.051kg
Environment
Operation temperature| Ta: -30 OC ~ +55 OC
Case temperature (Max.)| T c: +85OC
IP rating| IP20
Mechanical Structures and Installations
Systemwiring
Note:
- The above distance is measured in spacious(no obstacle) environment,
- Please refer to the actual test distance before installation.
- Users must use the Tuya ZigBee gateway to realize remote control and voice control.
Wiring diagram
Note:
An additional AC relay or contactor is needed when total input current of the load (such as pump) is higher than 1.5A.
Tuya APP network connection and operation
Press and hold Match/Set key for 2s, reset ZigBee network.
Press and hold Match/Set key for 5s, or push twice Match/Set key fastly,
Clear previous network connection, enter config mode. the blue LED indicator
fast flash.
Repeat power on and off for 5 consecutive times, also clear previous network
connection, enter config mode.
If Tuya APP network connection succeed, the blue LED indicator will stop
flash, and in Tuya APP, you can find ZB-SWITCH device.
Tuya APP interface operation:
Touch on/off key to turn on or off light.
SS-B(WZ) match RF remote control (Optional)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use the SS-B(WZ)’s Match key
Match:
Short press match key of SS-B(WZ), immediately press on/off key (single zone
remote) or zone key (multiple zone remote) on the remote.
Delete:
Press and hold match key of SS-B(WZ) for 10s to delete all match,
The light blinks 5 times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power of SS-B(WZ), then switch on power, repeat again,
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power of SS-B(WZ), then switch on power, repeat again,
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
SS-B(WZ) work as ZigBee-RF converter to match other RF switch or controller
End user can choose the suitable match/delete ways. Two options are offered
for selection:
Use the controller’s Match key
Match:
Short press match key of the controller, immediately press on/off key on the
Tuya APP. The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key of the controller for 5s, The LED indicator fast
flash a few times means match was deleted.Use Power Restart
Match:
Switch off the power of the controller, then switch on power, repeat again,
Immediately short press on/off key 3 times on the Tuya APP. The light blinks 3
times means match is successful.
Delete:
.Switch off the power of the controller, then switch on power, repeat again,
Immediately short press on/off key 5 times on the Tuya APP. The light blinks 5
times means match was deleted.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>