iskydance V1 Single Color LED Controller Instruction Manual

: June 8, 2024
: iskydance

Table of Contents

Features
Technical Parameters
Mechanical Structures and Installations
Wiring Diagram
Match Remote Control (two match ways)
- Use the controller’s Match key
- Use Power Restart
Application notes
Push Dim Function
Dimming Curve
Light on/off fade time
Malfunctions Analysis & Troubleshooting
Read User Manual Online (PDF format)
Download This Manual (PDF format)

iskydance V1 Single Color LED Controller

V1 Single Color LED Controller

Features

4096 levels 0-100% dimming smoothly without any flash.
Match with RF 2.4G single zone or multiple zone dimming remote control.
One RF controller accept up to 10 remote control.
Auto-transmitting function: Controller automatically transmit signal to another controller with 30m control distance.
Synchronize on multiple number of controllers.
Connect with external push switch to achieve on/off and 0-100% dimming function.
Light on/off fade time 3s selectable.
Over-heat / Over-load / Short circuit protection, recover automatically

Technical Parameters

Input and Output

Safety and EMC

EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED

Weight

Net weigh| 0.041kg
Gross weight| 0.052kg

Dimming data

Environment

Operation temperature| Ta: -30 OC ~ +55 OC
Case temperature (Max.)| T c: +85OC
IP rating| IP20
Warranty and Protection

Warranty| 5 years
Protection| Reverse polarity
Over-heat Over-load Short circuit

Mechanical Structures and Installations

Wiring Diagram

Match Remote Control (two match ways)

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key

Match:
Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote. The LED indicator fast flash a few times means match is successful.

Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.

Use Power Restart

Match:
Switch off the power of the receiver, then switch on power. Repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.

Delete:
Switch off the power of the receiver, then switch on power. Repeat again.
Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.

Application notes

All the receivers in the same zone.

Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m, as long as there is a receiver within 30m, the remote control distance can be extended. Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled by the same remote.
Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range. Strong signal sources such as WiFi routers and microwave ovens will affect the range.
We recommend for indoor applications that receiver placements should be no further apart than15m.
Each receiver(one or more) in a different zone, like zone 1, 2, 3 or 4.

Push Dim Function

The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switch’s.

Short press:
Turn on or off light.
Long press (1-6s):
Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction.
Dimming memory:
Light returns to the previous dimming level when switched off and on again, even at power failure.
Synchronization:
If more than one controller are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%.
This means there is no need for any additional synchrony wire in larger installations.
We recommend the number of controllers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to controller should be no more than 20 meters.