iskydance V1-M, V1-M(D) Single Color LED Mini RF Controller User Manual
- June 8, 2024
- iskydance
Table of Contents
Single Color LED Mini RF Controller
Model No.: V1-M, V1-M(D)
User Manual
V1-M, V1-M(D) Single Color LED Mini RF Controller
1 channel constant voltage/Max 5A output/Step-less dimming/Wireless remote control
|
---|---
V1-M
Cable In /Cable Out Version| V1-M(D)
DC Female Jack In /DC Male Jack Out Version
Model List
| Model | Photo | Power Connector | LED Connector |
|---|---|---|---|
| V1-M | Red/Black Cable 10cm | Red/Black Cable 10cm | |
| V1-M(D) | 5.5mm DC Female Jack | 5.5mm DC Male Jack |
Features
- 1 channel constant voltage single color LED mini RF controller.
- 5A output, connect with 5 meters single color LED strip.
- Match with RF 2.4G single zone or multiple zone dimming remote control.
- One RF controller accept up to 10 remote control.
- 4096 levels 0-100% dimming smoothly without any
- Auto-transmitting function: Controller automatically transmit signal to another controller with 30m control distance.
- Synchronize on multiple number of controllers.
Technical Parameters
Input and Output
Input voltage| 12-24VDC
Output voltage| 12-24VDC
Output current| Max. 5A
Output type| Constant voltage
Environment
Operation temperature| Ta: -30 ºC ~ +55 ºC
Case temperature (Max.)| Ta: +85 ºC
Dimming data
Input signal| RF 2.4GHz
Control distance| 30m(Barrier-free space)
Dimming gray scale| 4096 (2^12) levels
Dimming range| 0 -100%
Dimming curve| Logarithmic
PWM Frequency| 500Hz (default)
Warranty| 5 years
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certi| CE,EMC,LVD,RED
Package
Size| L90x H130mm
Gross weight| 0.021kg
Dimension
Wiring Diagram
Match Remote Control
Match:
Switch off the power of the receiver, then switch on power.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power of the receiver, then switch on power.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Another way to match:
The receiver is power on for five consecutive times, the LED strip light start
blinking slowly for 10s, Immediately short press on/off key (single zone
remote) or zone key (multiple zone remote) on the remote.
The light blinks 3 times means match is successful.
Dimming Curve
Malfunctions analysis & troubleshooting
| Malfunctions | Causes | Troubleshooting |
|---|---|---|
| No light | 1.No power. | |
| 2.Wrong connection or insecure. | 1.Check the power. |
2.Check the connection.
No response from the remote| 1.The battery has no power.
2.Beyond controllable distance.
3.The controller did not match the remote.| 1.Replace battery.
2.Reduce remote distance.
3.Re-match the remote.
Installation Precautions
- The products shall not be stacked, the distance should be ≥ 20cm, so as not to affect lifespan of the products due to poor heat dissipation.
- The product shall not be installed close to the switching power supply with an interval of ≥ 20cm to avoid the radiation interference of the switching power supply.
- The installation height shall be ≥ 1m from the tening the remote control distance due to too weak reception signal.
- The products are not allowed to be close to or covered by metal objects, with an interval of ≥ 20cm to avoid signal attenuation and shorten the remote control distance.
- Avoid installation at the corner of the wall or the corner of the beam, with an interval of ≥ 20cm to avoid signal interference.