iskydance V1-L Single Color LED Controller User Manual

iskydance V1-L Single Color LED Controller

Single Color LED Controller

Model No.: V1-L

Channel/Step-less dimming/Wireless remote control/Push Dim/Multiple protection

Features

• 4096 levels 0-100% dimming smoothly without any ash.
• Match with RF 2.4G single zone or multiple zone dimming remote control.
• One RF controller accept up to 10 remote control.
• Auto-transmitting function: Controller automatically transmit signal to another controller with 30m control distance.
• Synchronize on multiple number of controllers.
• Connect with external push switch to achieve on/off and 0-100% dimming function.
• Light on/off fade time 3s selectable.
• Over-heat / Over-load / Short circuit protection, recover automatically.

Technical Parameters

Input and Output

Input voltage| 12-48VDC
Output voltage| 12-48VDC
Output current| 15A@12/24V

10A@36/48V

Output power

| 180W@12V

360W@24V

360W@36V

480W@48V

Output type| Constant voltage
Dimming data

Input signal| RF 2.4GHz + Push Dim
Control distance| 30m(Barrier-free space)
Dimming gray scale| 4096 (2^12) levels
Dimming range| 0 -100%
Dimming curve| Logarithmic
PWM Frequency| 500Hz (default)
Environment

Operation temperature| Ta: -30 OC ~ +55 OC
Case temperature (Max.)| T c: +85OC
IP rating| IP20
Safety and EMC

EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3

ETSI EN 301 489-17 V3.2.4

Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED
Warranty and Protection

Warranty| 5 years

Protection

| Reverse polarity Over-heat Over-load Short circuit
Weight

Net weight| 0.099kg
Gross weight| 0.116kg

Mechanical Structures and Installations 

Wiring Diagram

Match with dimming remote

Connect with push switch

Match Remote Control (two match ways)

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key

Match:
Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote.
The LED indicator fast flash a few times
means match is successful.
Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times
means all matched remotes were deleted.

Application notes

1. All the receivers in the same zone. Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m, as long as there is a receiver within 30m, the remote control distance can be extended.
   Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled by the same remote.
   Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range. Strong signal sources such as WiFi routers and microwave ovens will affect the range.
   We recommend for indoor applications that receiver placements should be no further apart than15m.

2. Each receiver(one or more) in a different zone, like zone 1, 2, 3 or 4.

Push Dim Function

The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

• Short press:
  Turn on or off light.

• Long press (1-6s):
  Press and hold to step-less dimming,
  With every other long press, the light level goes to the opposite direction.

• Dimming memory:
  Light returns to the previous dimming level when switched off and on again, even at power failure.

• Synchronization:
  If more than one controller are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%.
  This means there is no need for any additional synchrony wire in larger installations.
  We recommend the number of controllers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to controller should be no more than 20 meters.

Dimming curve

Light on/off fade time

Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times.
Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

Malfunctions Analysis & Troubleshooting

2.  Wrong connection or insecure.

| 1.  Check the power.

2.  Check the connection.

Uneven intensity between front and rear,with voltage drop| 1. Output cable is too long.

2. Wire diameter is too small.

3. Overload beyond power supply capability.

4. Overload beyond controller capability.

| 1. Reduce cable or loop supply.

2. Change wider wire.

3. Replace higher power supply.

4. Add power repeater.

No response from the remote

| 1. The battery has no power.

2. Beyond controllable distance.

3. The controller did not match the remote.

| 1. Replace battery.

2. Reduce remote distance.

3. Re-match the remote.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>