iskydance V2-L(WZ)Zigbee &RF 2 in1 LED Controller User Manual
- June 5, 2024
- iskydance
Table of Contents
- iskydance V2-L(WZ)Zigbee &RF 2 in1 LED Controller
- Features
- Technical Parameters
- Mechanical Structures and Installations
- System wiring
- Wiring Diagram
- Tuya APP network connection
- Tuya APP interface
- PWM frequency setting
- V2-L(WZ) match remote control (Optional)
- V2-L(WZ) work as Zigbee-RF converter to match RF LED controller or
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
iskydance V2-L(WZ)Zigbee &RF 2 in1 LED Controller
Features
- 2 in 1 function, used for control color temperature or single color LED strip.
- DC12-48V input, 2 channel constant voltage output.
- Tuya APP cloud control, support on/off, color temperature and brightness adjust, delay turn on/off light, timer run, scene edit and music play function.
- Philips HUE APP control by connect with Philips HUE bridge.
- Voice control, support amazon ECHO and TmallGenie smart speaker.
- Match with RF 2.4G remote control optional.
- User need set light type by press key before Tuya APP network connection and match RF remote of the same light type.
- Each V2-L(WZ) controller can also work as Zigbee-RF converter, then use Tuya APP to control one or more RF LED controller or RF LED dimming driver synchronously.
- Light on/off fade time 3s selectable.
- Connect with external push key to achieve on/off and 0-100% dimming function.
- PWM frequency 500Hz, 2KHz, 8KHz or 16KHz selectable.
- Over-heat / Over-load / Short circuit protection, recover automatically.
Technical Parameters
Mechanical Structures and Installations
System wiring
Note:
-
The above distance is measured in spacious(no obstacle) environment,
Please refer to the actual test distance before installation. -
Users can also use the Tuya Bluetooth gateway to realize remote control and voice control.
Wiring Diagram
V2-L(WZ) for single color
V2-L(WZ) for dual color
Note:
- After changed the light type by DIP switch, please redo the tuya APP config operation.
- For CCT light type, continuous power on and off will change 3 levels color temperature (WW, NW and CW) in sequence.
- Switch off the power, then switch on power, repeat again. Immediately short press match key 3 times, the light on/off time will change between 3s and 0.5s.
Push Dim
Tuya APP network connection
- Press and hold Match key for 5s, or push twice Match key fastly:
- Clear previous network connection, enter config mode, the blue LED indicator fast flash, the output LED will flash 10 times.
- Repeat power on and off for 5 consecutive times, also clear previous network connection, enter config mode, the output LED will flash 10 times.
- If Tuya APP network connection succeed, the blue LED indicator will stop flash, and in Tuya APP, you can find ZB-DIM/CCT device.
Tuya APP interface
Music, Timer, Schedule
The music play can use smart phone music player or micro-phone as music signal
input.
The Timer key can turn on or turn off light in the next 24 hours.
The Schedule key can add multiple timers to turn on or turn off light according to different time periods. ‘
PWM frequency setting
We can select four PWM frequency: 500Hz, 2KHz, 8KHz or 16KHz. Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video).
V2-L(WZ) match remote control (Optional)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use the V2-L(WZ)’s Match key
Match:
Short press match key of V2-L(WZ),
immediately press on/off key (single zone remote) or zone key (multiple zone
remote) on the remote. The LED indicator fast flash a few times
means match is successful.
Delete:
Press and hold match key of V2-L(WZ) for 10s, The LED indicator fast flash a
few times
means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power of V2-L(WZ), then switch on power, repeat again.
Immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power of V2-L(WZ), then switch on power, repeat again.
Immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
V2-L(WZ) work as Zigbee-RF converter to match RF LED controller or
dimming driver
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
Match:
Short press match key of the controller, immediately press on/off key on the
Tuya APP. The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key of the controller for 5s, The LED indicator fast
flash a few times
means match was deleted.
Use Power Restart
Match:
Switch off the power of the controller, then switch on power, repeat again.
Immediately short press on/off key 3 times on the Tuya APP. The light blinks 3
times means match is successful.
Delete: a
Switch off the power of the controller, then switch on power, repeat again.
Immediately short press on/off key 5 times on the Tuya APP. The light blinks 5
times means match was deleted.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>