lionelo Thermup Bottle warmer User Manual

lionelo Thermup Bottle warmer

Dear Customer
In case of any questions or comments on the purchased product, please contact us: help@lionelo.com

Producer:
BrandLine Group Sp. z o. o. ul. A. Kręglewskiego 1, 61-248 Poznań, Poland.

The product meets the requirements of EU directives
Pursuant to the Directive 2012/19/EU, this product is subject to selective collection. Do not dispose of the product together with domestic waste as it may pose a threat to the environment and people’s health. The worn-out product must be handed over to the electrics and electronics recycling center.

Recommended working conditions

• Humidity: 50-80%
• Temperature: 15-30°C (59-86°F)

IMPORTANT
Please read this manual before you start using the product to see its functions and use it in accordance with its intended use. A failure to follow the safety instructions and use at variance with the manual may cause bodily injuries.

Keep this manual for future reference

1. Do not repair or modify the device on your own. Only an authorized service technician is allowed to perform these operations.
2. This device is not a toy. Do not let children play with it. Keep the device out of reach of children.
3. The device can be used by children aged at least 3 and persons with limited physical, sensory or mental capabilities, as well as persons who lack suitable knowledge and experience in using the device as long as their actions are supervised or if they have been instructed on safe use of the product and related risks beforehand.
4. Cleaning and maintenance of the device can be performed by children aged at least 8 and under supervision. Keep the device and power cable out of reach of children below the age of 3.
5. The device is intended for home use only. The device is not suitable for use in the open air. Do not use it for other purposes, at variance with intended use.
6. Do not let the power cable hang on the edge of the table or top. Make sure the power cable does not contact hot pieces. Do not pull it through sharp edges.
7. Connect the device only to a mains socket with earthing. Make sure the power cable has been correctly connected to the source of power supply.
8. To supply power to the device, use networks whose parameters correspond to parameters on the device label.
9. Regularly check the device for potential damage. Do not use the device if it is damaged. Do not try to repair the device on your own – contact the authorized repair center. If the network cable gets damaged, it should be replaced by the manufacturer in order to avoid hazards.
10. After use, during assembly, disassembly and cleaning, the device must be deactivated and unplugged.
11. Keep the device away from sharp edges and sources of heat and moisture. Do not expose the device to direct sunlight.
12. Do not immerse the device or power cable in water or other liquids.
13. Make sure the device does not overheat.
14. Before you put the bottle into the warmer and pour water, make sure it is tight.
15. Before you switch the device on, make sure there is water inside. Never turn the device on when water is missing.
16. Hot water may cause serious burning. If there is hot water in the device, please remain careful.
17. The surface of the device may get hot under the influence of hot water. Please remain careful.
18. Do not move the device which contains hot water.
19. When food reaches the desired temperature, take the bottle out of the warmer. Do not heat food too long.
20. Always check food temperature before you feed the child.
21. Before you start cleaning the device, wait until the device cools down.

List of parts

1. Cover
2. Bottle/container holder
3. Warmer
4. Status LED
5. Defrost/quick heat
6. Milk heating
7. On/off switch
8. Value up
9. Food heating
10. Disinfect
11. Change mode
12. Value down

Defrosting

1. Place a bottle or container with food in the warmer (fig. 1).
2. Pour water into the warmer until you reach food or milk level. In the case of a large amount of food or milk, the maximum amount of water in the warmer is about 1,5 cm below the upper edge of the device (fig. 2).
3. Choose to defrost/quick heat in the display (fig. 3). Wait for the status LED to glow.

NOTE

• Due to the high diversity of baby food consistency, it is advisable to frequently stir and inspect the temperature of food defrosted.
• Do not serve milk/food shortly after defrosting.

Quick heating

1. Place a bottle or container with food in the warmer (fig. 1).
2. Pour 40 ml of water into the warmer (see: table below) (fig. 2).
3. Select defrost/quick heat in the display (fig. 3). Wait for the status LED to glow.
4. Do not heat frozen milk or food. Remember to heat milk or food after defrosting.

NOTE
In case of quick heating, use the device together with a cover.

40ml/1.4oz

| 3 min| 4 min| 5 min| 6 min
20°C/68°F| 2,5 min| 3 min| 4 min| 4,5 min
Plastic| 4°C/41°F| 4 min| 5,5 min| 6 min| 7 min
20°C/68°F| 3 min| 3,5 min| 4,5 min| 5 min

Milk heating

1. Place a bottle with milk or water in the warmer (fig. 4).
2. Pour water into the warmer until you reach milk or water level in the bottle. In case of a large amount of water or milk, the maximum amount of water in the warmer is about 1,5 cm below the upper edge of the device (fig. 5).
3. Select heating in the display (fig. 6). Wait for the status LED to glow.
4. Heating time may vary, depending on the amount of milk or water and initial temperature.

NOTE
It is advisable to serve milk to the child shortly after heating. Avoid milk reheating. Always check milk temperature before you serve it to the child (fig .7).

Food heating

1. Place a container with food in the warmer (fig. 8).
2. Pour water into the warmer until you reach food level in the container. In case of a large amount of milk or water, the maximum amount of water in the warmer is about 1,5 cm below the upper edge of the device (fig. 9).
3. Select food heating in the display (fig. 10). Wait for the status LED to glow.
4. It is advisable to stir food while heating (fig. 11).
5. Before serving, always check food temperature (fig. 12).

NOTE
Due to high diversity of baby food consistency, it is advisable to frequently stir it and inspect the temperature. It is not possible to precisely specify food heating time.

Disinfecting

1. Before you start disinfecting, wash and carefully rinse the bottle and accessories.
2. Place accessories and a bottle upside down in the warmer (fig. 13).
3. Pour about 50-100 ml of water into the warmer (fig. 14).
4. Select disinfection in the display (fig. 15). Wait for the status LED to glow.
5. When water evaporates, the device shuts down automatically.

**Cleaning

**

1. After every use and before cleaning, unplug the device. Wait so that the device can cool down before you start cleaning.
2. Remove water from the device (fig. 16).
3. If you have heated food in the device, make sure there are no remains at the bottom.
4. Wipe the housing and interior of the warmer with a soft wet cloth, and then wipe it dry with a clean cloth or paper towel (fig. 17).
5. For cleaning, do not use scrub sponges, scrub agents or any other caustic substances or chemicals.

Descaling

1. It is advisable to perform descaling on a regular basis, that is every four weeks, to assure correct operation of the device.
2. Pour 50 ml of white vinegar and 100 ml of cold water into the device.
3. Turn the device on and then select milk heating. Let the device work for 10 minutes.
4. Leave the solution in the device until descaling is successful.
5. Before you empty the device, remember to unplug it.
6. Pour the solution out. Pour water into the device, rinse the remains of the solution and then empty the device.

NOTE
You can also use descalers based on citric acid. Do not use other kinds of descalers.

The pictures are for reference only. The real design of the products may differ from the pictures presented.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>