respekta KG Series Fredge-Freezer User Manual

respekta KG Series Fredge-Freezer

Dear customer! We would like to thank you for purchasing a product from our wide range of domestic appliances. Read the complete instruction manual before you operate the appliance for the first time. Retain this instruction manual in a safe place for future reference. If you transfer the appliance to a third party, also hand over this instruction manual.

Low-frost technology, for comfortable defrosting. The appliance is characterized by the most advanced defrosting techniques. In the freezing area, the low-frost technique helps for significantly reduce the need for defrosting.

EU – Declaration of Conformity

• The products, which are described in this instruction manual, comply with the harmonized regulations.
• The relevant documents can be requested from the final retailer by the competent authorities.

The figures in this instruction manual may differ in some details from the current design of your appliance. Nevertheless follow the instructions in such a case. Delivery without content.
Any modifications, which do not influence the functions of the appliance. shall remain reserved by the manufacturer. Please dispose of the packing with respect to your current local and municipal regulations.
The appliance you have purchased may be an enhanced version of the unit this manual was printed for. Nevertheless, the functions and operating conditions are identical. This manual is therefore still valid. Technical modifications as well as misprints shall remain reserved.

Safety instructions

Read the safety instructions carefully before you operate the appliance for the first time. All information included in those pages serve for the protection of the operator. If you ignore the safety instructions, you will endanger your health and life.

DANGER! Indicates a hazardous situation which, if ignored, will result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury.

WARNING! Indicates a hazardous situation which, if ignored, could result in death or serious injury.
NOTICE! Indicates possible damage to the appliance.

Store this manual in a safe place so you can use it whenever it is needed. Strictly observe the instructions to avoid damage to persons and property.
Check the technical periphery of the appliance! Do all wires and connections to the appliance work properly? Or are they time-worn and do not match the technical requirements of the appliance? A check-up of existing and newly- made connections must be done by an authorized professional. All connections and energy-leading components (incl. wires inside a wall) must be checked by a qualified professional. All modifications to the electrical mains to enable the installation of the appliance must be performed by a qualified professional. The appliance is intended for private use only as well as to be used (1) in staff kitchen areas of shops, offices and other working environments; (2) by clients in hotels, motels, B&B and other residential type environments; (3) for catering and similar non-retail applications.
The appliance is intended for cooling food only.
The appliance is intended for indoor-use only.
The appliance is not intended to be operated for commercial purposes, during camping and in public transport.
Operate the appliance in accordance with its intended use only.
Do not allow anybody who is not familiar with this instruction manual to operate the appliance.
This appliance may be operated by children aged from 8 years and above as well as by persons with reduced physical, sensory and mental capabilities or lack of experience and knowledge if they are supervised or have been instructed concerning the safe use of the appliance and do comprehend the hazards involved. Children must not play with the appliance. Cleaning and user- maintenance must not be carried out by children unless they are supervised.

DANGER!

1. Do not connect the appliance to the mains if the appliance itself or the power cord or the plug are visibly damaged.
2. Never try to repair the appliance yourself. If the appliance does not operate properly, please contact the shop you purchased the appliance at. Original spare parts should be used only.
3. When the power cord is damaged, it must be replaced by the manufacturer or an authorized aftersales service or a qualified professional only.

WARNING!

1. This appliance is equipped with the environmental-friendly refrigerant R600a. The refrigerant R600a is inflammable. The components of the cooling circuit must neither be damaged during transport nor use.
2. If any part of the cooling circuit is damaged, the appliance must not stand near a fire, naked light or spark-generating devices. Contact the shop you purchased the appliance at immediately.
3. If gas is set free in your home:
   • Open all windows.
   • Do not unplug the appliance and do not use the control panel or thermostat.
   • Do not touch the appliance until all the gas has gone.
   • Otherwise sparks can be generated which will ignite the gas.
4. Keep all components of the appliance away from fire and other sources of ignition when you dispose of or decommission the appliance.
5. EXPLOSION HAZARD! Do not store any explosive materials or sprays, which contain flammable propellants, in your appliance. Explosive mixtures can explode there.
6. While unpacking, the packaging materials (polythene bags, polystyrene pieces, etc.) should be kept away from children. CHOKING HAZARD.
7. Do not connect the appliance to the electric supply unless all packaging and transit protectors have been removed.
8. Operate the appliance with 220~240V/50Hz/AC only. All connections and energy-leading components must be replaced by an authorized professional.
9. Do not use a socket board or a multi socket when connecting the appliance to the mains.
10. Do not connect the appliance to an energy saving plug (e.g. Sava Plug) and to inverters which convert direct current (DC) into alternating current (AC), e.g. solar systems, power supply of ships.
11. A dedicated and properly grounded socket meeting the data of the plug is required to minimize any kind of hazard. The appliance must be grounded properly.
12. Check that the power cord is not placed under the appliance or damaged when moving the appliance.
13. The technical data of your energy supplier must meet the data on the model plate of the appliance.
14. Your domestic circuit must be equipped with an automatic circuit breaker.
15. Do not modify the appliance.
16. Turn off the power before you install the appliance and before you connect it to the mains. RISK OF FATAL ELECTRIC SHOCK!
17. Disconnect the appliance from the mains before you clean or maintain it.
18. Do not use any electric appliances inside the food storage compartments of your appliance unless they are recommended by the manufacturer of your refrigerator.
19. Do not put any heat-radiating appliances onto your appliance.
20. Do not install the appliance in a place where it may come in contact with water/rain; otherwise the insulation of the electrical system will be damaged.
21. Do not put a water-boiler or vases onto your appliance. The electrical components of your appliance can be seriously damaged by water over-boiling or spilled water.
22. Do not use any steam cleaners to clean or defrost the appliance. The steam can get into contact with the electrical parts and cause an electrical short. RISK OF ELECTRIC SHOCK!
23. Never use mechanic devices, knives or other sharp-edged items to remove encrusted ice inside the appliance. RISK OF ELECTRIC SHOCK caused by damaging the interior of the appliance.
24. Children must never play with the appliance.
25. If you decommission your appliance (even temporarily), ensure that children cannot get into the appliance. Strictly observe the corresponding safety instructions numbers. 1 and 4, chapter DECOMMISSIONING, ultimate
26. Strictly observe the instructions in chapter INSTALLATION.

CAUTION!

1. The condenser and the compressor, located at the rear of the appliance, can reach high temperatures during ordinary operation. Carry out the installation according to this manual. An insufficient ventilation of the appliance will impair its operation and will damage the appliance. Do not cover or block the ventilation slats at any time
2. Do not put any gassy beverages into the freezer compartment of the appliance, because their containers could explode.
3. Do not touch the extremely cooled surfaces with wet or damp hands, because your skin may stick on these surfaces.

NOTICE

1. When you move the appliance, hold it at its base and lift it carefully. Keep the appliance in an upright position.
2. Do not tilt the appliance more than 450.
3. If the appliance is transported in a horizontal position, some oil may flow from the compressor into the refrigerant circuit.
4. Leave the appliance in an upright position for 4-6 hours before you switch it on to ensure, that the oil has flowed back into the compressor.
5. Never use the door for moving the appliance as you will damage the hinges.
6. The appliance must be transported and installed by at least two persons.
7. When you unpack the appliance, you should take note of the position of every part of the interior accessories in case you have to repack and transport it at a later point of time.
8. Do not operate the appliance unless all components are installed properly.
9. Do not stand or lean on the base, the drawers, the doors etc of the appliance.
10. Do not put hot liquids or hot foodstuff into the appliance.
11. The air vents of the appliance or its built-in structure (if the appliance is suitable for being built-in) must be completely open, unblocked and free of any kind of dirt.

Climatic classes

Look at chap. TECHNICAL DATA for information about the climatic class of your appliance. Your appliance can be operated in rooms with relevant room temperatures as named below.

Installation

Site

1. Unpack the appliance carefully. Dispose of the packaging as described in chapter waste management.
2. The accessories of your appliance can be protected from damage due to transportation (adhesive tapes etc.). Remove such tapes very carefully. Remove remains of such tapes with a damp cloth using lukewarm water and a mild detergent (see also chapter CLEANING AND MAINTENANCE). Never remove any components of the back of the appliance!
3. Install the appliance in a suitable position with an adequate distance from sources of heat and cold.
4. Check that the appliance and the power cord are not damaged.
5. Install the appliance in a dry and well-ventilated place.
6. Protect the appliance from direct sunlight.
7. The doors must open completely and without hindrance.
8. Install the appliance on a level, dry and solid floor. Check the correct installation with a bubble level.
9. Connect the appliance to the mains properly.
10. The nameplate is inside the appliance or at the back.

Ventilation

Minimum distances required for proper ventilation:

• Back ↔ wall Min. 50 mm
• Right/left ↔ any piece of furniture/wall Min. 10 mm

Free space above
If any objects (e.g. shelves) are directly mounted above the appliance, the energy consumption can increase significantly and heat accumulation may occur.

Door space requirements WD ≥ 843892 mm

Levelling

1. Use the adjustable feet at the front to level the appliance properly.
2. When the appliance is not levelled, the door and the magnetic seals will not close properly.
3. Ensure that the feet touch the floor properly before operation.

Changing of the hinge position

WARNING! Switch off and unplug the appliance before changing the hinge position. RISK OF ELECTRIC SHOCK!
CAUTION! The change of the hinge position must be carried out by at least two persons; otherwise you may hurt yourself or damage the appliance. Do not tilt the appliance more than 450.
NOTICE! Adjust the door properly. The seal must close properly.

Always lift the doors carefully. Store the doors at a place, where they cannot be damaged.

1. Remove the top hinge cover.
2. Remove the top hinge.
3. Remove the door of the fridge.
4. Remove the middle hinge using a screwdriver.
5. Remove the door of the freezer.
6. Remove the bottom hinge assembly using a screwdriver and install it on the opposite side.
7. Place the door of the freezer on the bottom hinge.
8. Install the middle hinge on the opposite side.
9. Install the door of the fridge
10. Install the top hinge cover.

Operation

Main components

AFTER INSTALLATION WAIT 4-6 HOURS
BEFORE YOU CONNECT YOUR APPLIANCE TO THE MAINS!

Temperature control

• MIN: Warmest refrigeration temperature.
• MED: Normal operation, suitable for most situations.
• MAX: Coldest refrigeration temperature.

1. Before initial use: Clean the appliance. Read the information given in chapter CLEANING AND MAINTENANCE. Check that the appliance is levelled and ventilated properly.
2. Set the thermostat to MED for initial operation.
3. Wait approx. 24 hours before you store any food in the appliance.
4. When the appliance has been disconnected from the mains or switched off or in case of a power failure, you must wait 3 to 5 minutes before restarting the appliance.
5. The description of the setting levels represents standard values only.
6. You can check the cooling/freezing temperature using a fridge/freezer thermometer (not included in delivery).
7. The setting definitions are standard values only.
   WARNING The setting 0/OFF switches off the compressor only. You must unplug the appliance to disconnect it from the mains.

Operational parameters

1. The appliance can only reach the relevant temperatures when:
   • the a ambient temperature meets the climatic class.
   • the doors close properly.
   • you do not open the doors too often or too long.
   • the door seals are in proper condition.
   • the appliance is properly positioned.
   • you have not overfilled the appliance.
   • you do not store warm or hot food in the appliance.
2. When the ambient temperature is very high, it is recommended to set the thermostat to a colder setting if needed. If the colder setting should cause strong formation of encrusted ice, please select a lower setting.
3. High ambient temperatures and simultaneously operating at the coldest setting may make the compressor operate permanently to keep the temperature constant inside the appliance.
4. Defrost the appliance periodically as encrusted ice will decrease the power and increase the energy consumption of the appliance.

Helpful hints/energy saving

• Cooked food can be stored in the appliance. Let it cool down to room temperature before you put it into your appliance.
• Store your food in colourless, airtight and tasteless materials.
• Some food like meat, fish etc. may become dry and release strong odours. You can avoid these by wrapping them into aluminum foil or plastic wrap or putting them into an airtight bag or container.
• Allow ample storage place for your food. Do not overfill your appliance.
• Wrap your food in plastic wrap or suitable paper and place each kind of food in a particular location in your appliance. This will prevent any contamination, a loss of water and a mingling of odours.
• Let warm or hot food cool down to room temperature before you put it into your appliance. Otherwise the energy consumption will increase.
• Put the frozen food you want to defrost into the cooling-compartment of you appliance.
• Try opening the door as little as possible, especially when the weather is warm and humid. If you open the door, close it as fast as possible.
• Permanently check, that the appliance is well-ventilated. The appliance has to be well-ventilated from all sides.

How to freeze food

1. Wrap fresh food you want to freeze in aluminum foil, cling film, air and water tight plastic bags, polyethylene containers or other suitable plastic containers with a lid.
2. Leave some free space between the single pieces of frozen food as proper air circulation is required.
3. The food is frozen completely after 24 hours (you find the relevant information about the maximum freezing capacity within 24 hours in chapter technical data).
4. Only buy frozen food, when its packaging is not damaged. Damaged packaging may indicate an interruption of the cold chain.
5. Avoid or reduce variations in temperature: buy frozen food at the end of shopping and transport it in thermally insulated bags.
6. Do not refreeze defrosted and semi-defrosted food. Consume within 24 hours.
7. Observe the complete information on the packaging of frozen food.
8. Making of ice cubes: Fill an ice cube tray (commercially available) 2/3 full and place it in the freezer. Dry the form before, so it cannot freeze-up. Do not use any sharp-edged or pointed items to remove the ice cube tray if it is frozen on the freezer compartment. Hold the tray under flowing cold water and twist the ice cube form slightly when removing the ice cubes.

Cleaning and maintenance

1. WARNING! Disconnect the appliance from the mains before you clean or maintain it.
2. Always keep the appliance clean so that unpleasant odours do not occur.
3. Dust deposits on the condenser will increase the energy consumption. Clean the condenser twice a year with a vacuum cleaner or a soft brush.
4. Take off all rings and bracelets before cleaning or maintaining the appliance; otherwise you will damage the surface of the appliance.

Detergent

• Do not use any harsh, abrasive or aggressive detergents.
• Do not use any solvents.
• Do not use any abrasive detergents! Do not use any organic detergents! 2Do not use essential oils!
• These instructions are valid for all surfaces of your appliance.

External cleaning

1. Use a moist cloth and a mild, non-acidic detergent. Use a suitable detergent for stubborn stains.
2. Use clear water to rinse.
3. Dry the cleaned surfaces with a cloth.

Internal cleaning

1. Clean the shelves and the inside with warm water and a mild detergent.
2. Use clear water to rinse.
3. Dry the cleaned surfaces with a cloth.
4. Check the water drain and clean it if needed.

Door seals

• Clean with warm water and a mild, non- acidic detergent.

Detergents such as vinegar, citric acid etc.

Defrosting Fridge:

1. The fridge is defrosted automatically. The water runs in a container near the compressor, where it evaporates.

Freezer:

WARNING! Never use any mechanical items, knives or other sharp- edged objects to remove the encrusted ice. RISK OF ELECTRICAL SHOCK!

1. Remove the contents and put them into a cooling box.
2. Switch off the appliance by turning the thermostat to position 0/AUS/OFF and disconnect it from the mains.
3. When the encrusted ice melts put some dry cloths into the appliance to hold the water back.
4. Do not support the defrosting procedure with hot water.
5. Remove the big pieces of ice first. Then remove the small pieces of ice.
6. Clean and dry the appliance and door seals with soft cloths.
7. Leave the door of the appliance open for a while.

Replacing of the illuminant

1. WARBNING! Switch off the appliance and pull out the mains plug.
2. The illuminant must be replaced by a qualified professional only.

• According to the EU regulation No. 244/2009, your appliance is classified as a household appliance in accordance with the ecodesign requirements for non- directional household lamps. This means that bulbs, which are used in household appliances, must not be used to illuminate domestic establishments.

Trouble shooting

MALFUNCTION

If the appliance shows a malfunction not noted on the schedule above or if you have checked all items on the above schedule but the problem still exists, please contact the aftersales service.

The operating conditions described below are normal and do not indicate a malfunction.

• The refrigerant generates a sound similar to flowing water.
• Sometimes you may hear a sound which is generated by the injection process of  the cooling circuit.
• The sides of the appliance may get warm while the appliance is running.

Distinct noise
When you operate the appliance for the first time or the temperature falls below a certain level, the appliance will operate with high power to reach the present temperature.

Condensed water in/on the appliance
May be generated inside or outside the appliance by high humidity or very warm ambient temperatures.

Clicking
You will hear the compressor click if it is activated or deactivated.

Hum
Is caused by the compressor while running.

Knocking/snapping
May be generated by sequential expansion and shrinkage of the components of the cooling system. It is caused by variation of temperature before and after the compressor is activated or deactivated.

Decommissioning

Decommissioning, temporarily

• If the appliance is not used for a longer period of time:
  1. Draw the plug out of the socket.
  2. Remove all food stored in the appliance.
  3. Dry the inside of the appliance with a cloth and leave the door open for a few days.
• While away on an average vacation/holiday (14-21 days):
  1. Do the same as described above, or
  2. Let the appliance operate.
  • Remove all perishable food from the cooling compartment.
  • Clean the cooling compartment.
  • Freeze all food which is suitable to be frozen.
• If you want to move the appliance:
  1. Secure all removable parts and the contents of the appliance. Pack them separately if necessary.
  2. Transport the appliance in an upright position only. All other positions can cause damage to the compressor.
  3. Do not damage the feet of the appliance.

Decommissioning, ultimate

1. Draw the plug out of the socket.
2. Cut off the power cord at the appliance.
3. Completely remove every door of the appliance.
4. Leave the shelves in their position so that children are not able to get into the appliance.
5. Follow the advice for the disposal of the appliance in chapter WASTE MANAGEMENT.

Technical data

• Model Freezer-Fridge

• Climatic class ST -N

• Energy efficiency class* A++

• Annual energy consumption in kW/h** 162.00

• Voltage/frequency 220-240V AC/50Hz

• Volume gross/net/freezer in l 170/116/51

• Noise emission 41 dB/A

• Stars 4****

• Freezing capacity/24 h 2.00 kg

• Max. storage time/malfunction 15.00 h

• Adjustable thermostat yes

• Compressor 1

• Refrigerant R600a

• Changeable hinge position yes

• Adjustable feet 2/front

• Defrosting cooling comp./freezer automatically/manual

• Dimensions appliance HWD in cm 141.8050.0054.00

• Weight net/gross in kg 41.00/45.50

• On a scale from A+++ (highest efficiency) to D (lowest efficiency).
  ** Based on standard measurement results within 24 hours. The current energy consumption depends on the way the appliance is used as well as on its site.

Waste management

1. Dispose of the appliance relevant to the current legislation in view of explosive gases. The cooling systems and insulation of refrigerators and freezers contain refrigerants and gases which have to be deposed of properly. Do not damage the cooling fins and tubes. If refrigerants escape there is FIRE HAZARD!
2. While unpacking, the packaging materials (polythene bags, polystyrene pieces, etc.) should be kept away from children. CHOKING HAZARD!
3. Old and unused appliances must be send for disposal to the responsible recycling centre. Never expose to open flames.
4. Before you dispose of an old appliance, render it inoperative. Unplug the appliance and cut off the entire power cord. Dispose of the power cord and the plug immediately. Remove the door completely so children are not able to get into the appliance as this endangers their lives!
5. Dispose of any paper and cardboard into the corresponding containers.
6. Dispose of any plastics into the corresponding containers.
7. If suitable containers are not available at your residential area, dispose of these materials at a suitable municipal collection point for waste-recycling.
8. Receive more detailed information from your retailer or your municipal facilities.

Refrigerant

1. The refrigerant circuit of the appliance contains the refrigerant R600a, a natural gas of high environmental compatibility.
2. WARNING! Do not damage any components of the refrigerant circuit while transporting the appliance. FIRE HAZARD!

Materials marked with this symbol are recyclable. Please contact your local authorities to receive further information. The refrigerant R600a is flammable!

GUARANTEE TERMS

The manufacturer assumes no responsibility for damage caused by the buyer.

This device has been manufactured and tested according to the latest methods.

Irrespective of the seller’s / dealer’s statutory warranty obligation, the manufacturer provides a 6-month warranty for faultless material and faultless production for a period of 24 months from the date of purchase.

The warranty expires in case of intervention by the buyer or by third parties.

Damage caused by improper handling or operation, by incorrect installation or storage, by improper connection, improper installation, as well as by force majeure or other external influences, are not covered by the guarantee.

We reserve the right to repair or replace defective parts or to exchange the device in case of complaints.
Only if repair (s) or replacement of the device, the intended use by the manufacturer should not be finally achieved, the buyer can demand warranty within six months, calculated from the date of purchase, reduction of the purchase price or cancellation of the purchase contract.

Claims for damages, including consequential damages, unless they are based on intent or gross negligence excluded.
In the case of unnecessary or unjustified use of the customer service, we charge the usual time and track charge for our service.

Complaints must be reported immediately after the detection of an error.
The replacement of light bulbs by our customer service technician is not subject to the guarantee guidelines and is therefore subject to a charge. There is no guarantee for bulbs.

The warranty claim has to be proven by the buyer, by presenting the purchase receipt. The guarantee is valid within the Federal Republic of Germany.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>