lionelo Baby line SMART video monitor User Manual
- June 5, 2024
- lionelo
Table of Contents
lionelo Baby line SMART video monitor
Dear Customer!
In case of any questions or comments on the purchased product, please contact
us: help@lionelo.com
Producer:
BrandLine Group Sp. z o. o. ul. A. Kręglewskiego 1, 61-248 Poznań, Poland
Product information
- Frequency: 2.412-2.472 GHz
- Output power RF: 12.99 dBm
- Card format: FAT32
- microSD card maximum capacity: 128 GB
Important
- This product is not a toy. Do not let children play with it.
- The product must be used in dry places only. It is forbidden to use it outdoors or on a wet surface.
- Do not touch the product if your hands are wet.
- If the product malfunctions or has been dropped or flooded, please contact the manufacturer’s service center.
- Use only the power adapter supplied.
- It is forbidden to place the product near a cooker or other sources of heat.
- Installation must be carried out only by an adult. Keep minor pieces of the set out of reach of children.
- The baby monitor cannot replace proper attention and parent’s care.
- Do not place the product and its cables in the playpen or within the child’s reach. Place them at a distance of at least 1 m.
- Do not place the product near water or sources of fire.
- Do not touch plug pins with sharp or metal items.
The product complies with requirements of EU directives.
Pursuant to the Directive 2012/19/EU, this product is subject to selective
collection. The product must not be disposed of together with domestic waste
because it may pose a threat to the environment and human health. The worn-out
product must be handed over to the electrics and electronics recycling point.
Set (fig. A)
- Camera
- Power adapter
- USB cable
- Adhesive tape
- Mounting bracket x3
- Temperature and humidity sensor
- Screws x3
- Operating manual
- Decorative cover
- Rawlplugs x3
Product description (fig. B)
- Light indicator
- USB input
- Reset key
- Loudspeaker
- microSD card port
- Microphone
How to start the camera and run the application
Find and download Lionelo Smart application from iOS Store/Google Play store,
or scan QR code at the beginning of the operating manual.
Note: Only Wi-Fi 2.4 GHz networks are supported. 5 GHz networks are not
supported.
- Sign up in the application through your e-mail address. Accept the terms of use.
- Select the user name and password, and then click „Confirm”. Enter the code you have received in your mailbox.
- While configuring, set the camera as close to the Wi-Fi router as possible to boost the pairing procedure (fig. 6).
Note: the camera can be added only to one account in the application.
To add the camera to other account, it must be deleted from the previous
account.
- Supply power to the camera through a USB cable.
- Select „Add new device”.
- Reset the camera by pressing and holding the reset key for 5 seconds (3, fig. B).
- Select Wi-Fi network which you wish to connect to and enter the password.
- You will see QR code in the application. Place the mobile phone at a distance of about 20 cm from the camera (fig. 7). Wait for the camera to give a sound. Configuration should be completed within about 30 seconds.
Light indicator
- The light glows in red – no connection.
- The light flashes in red – the camera awaits Wi-Fi connection.
- The light glows in blue – the camera works properly.
- The light flashes in blue – the camera awaits connection to the application.
Device functions
- The application allows you to play melodies through the baby monitor.
- Videos and photographs are saved in the user’s mobile phone, or on the microSD card, if it has been inserted into the baby video monitor.
- The application allows a two-way audio communication with the child.
- Image rotation in the screen – turn the video vertically and horizontally at any time.
- Motion and sound sensors will notify you in case of detection of motion or sound in the room.
- Day/ Night – this function assures a night vision of up to 10 m.
- Full description of application functions is available on Lionelo website.
Temperature and humidity sensor
Connect the temperature and humidity sensor to the longitudinal tip of the
camera (fig. 8).
After starting the camera, temperature and humidity in the room will be
available in the application.
Reset key
Press and hold the reset key for 5 seconds to reset the camera and restore the factory settings.
How to install
The longitudinal tip can be set in any way (fig. 1). To install the camera on
the wall, use the mounting bracket. The bracket can be attached to the wall
with the use of screws or adhesive tape (fig. 2).
How to install with screws
-
Mark the spot on the wall in which you wish to drill holes for rawlplugs (fig. 3).
-
Make a hole with a tool suitable for the specific surface and then put rawlplugs in (fig. 4).
-
Fix the assembly bracket by screwing screws in (fig. 5).
-
Place the camera on the wall and position for the best angle of view.
How to install with screws
- Mark the spot on the wall in which you wish to drill holes for rawlplugs (fig. 3).
- Make a hole with a tool suitable for the specific surface and then put rawlplugs in (fig. 4).
- Fix the assembly bracket by screwing screws in (fig. 5).
- Place the camera on the wall and position for the best angle of view.
Troubleshooting
Problem/question | Possible solution |
---|---|
The camera is not visible in the application. | Check Wi-Fi signal strength or |
place the camera near the router while configuring. Reset the camera and add
it again.
The camera is still in the list of devices in the application after
resetting.| Resetting changes camera settings only. The camera must also be
deleted in the application.
How to change Wi-Fi network which the camera is connected to?| Delete the
camera from the list of devices in the application, and then configure it
again by connecting to other network.
The camera cannot identify microSD card.| It is advisable to insert microSD
card when the camera is off. Make sure the card is available and comes in
FAT32 format and its maximum capacity is 128 GB. Check Internet connection.
No notifications in the application.| Make sure the application works
properly, and notifications have been activated. Check notification settings
in the mobile phone.
The camera does not want to connect to the application. The message pops up to
inform the camera has been paired before.| The camera can be added only to one
account in the application. To add the camera to other account, it must be
deleted from the previous account.
The pictures are for reference only. The real design of the products may differ from the pictures presented.
Simplified EU declaration of conformity
BrandLine Group Sp. z o. o. hereby declares that the “ BABYLINE SMART” product
complies with the directive: 2014/53/EU – RED Directive,2014/30/EU – EMC
Directive, 2014/35/EU – LVD Directive, 2011/65/EU – RoHS Directive. Full
content of EU declaration of conformity is available on the following website:
www.lionelo.com/deklaracja_zgodnosci/BABYLINE_SMART.pdf
Thank you for purchasing our product
www.lionelo.com
Documents / Resources
|
lionelo Baby line SMART video
monitor
[pdf] User Manual
Baby line SMART video monitor, SMART video monitor, video monitor
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>