lionelo Bastiaan RWF Baby car seat User Manual

User manual
Bastiaan RWF

Baby car seat

Dear customer!
Should you have any remarks or questions concerning the product, please do not hesitate to contact us: help@lionelo.com
Before you use the child safety seat for the first time, please read this manual carefully.
Producer:
BrandLine Group Sp. z o. o.
ul. A. Kręglewskiego 1, 61-248 Poznań, Poland
Important
Please read this manual before you use the product and keep it for future reference. The manual can help you assemble the child safety seat properly. A wrong assembly may pose a threat to your child. The manufacturer shall not be held responsible for potential damage arising from the wrong assembly of the seat.

This child safety seat is intended for weight categories (groups): 0, 0+, I, II, and III, which means it can be used by children whose weight does not exceed 36kg.
Weight group 0, 0+: 0-13 kg,
Weight group I: 9-18 kg,
Weight group II: 15-25 kg,
Weight group III: 22-36 kg.

• Hard elements and plastic parts of the child restraint system must be placed and installed in a way that they do not get trapped by a sliding seat or vehicle door if the vehicle is used normally.

• For a rear-facing position: do not use the child safety seat in places in which an airbag is active.

• The belts which hold the child’s safety seat must be tightened properly.

• Any safety belts which hold the child must be well-adapted to its body. The belts must not be twisted.

• Make sure the hip belts go low so that a pelvis is properly supported.

• Any accident or collision may damage the child’s safety seat, even if you cannot see it.
  If the device has been subject to sudden overloads during accidents, please replace it. In case of any doubts, please contact the seller or manufacturer.

• Do not modify the child safety seat or install any additional elements unless a technical certification body has approved it. To provide your child with top safety, fix and use the device in accordance with the manual.

• Please c elements of this child safety seat may heat up in the sun and cause sunburns.

• Protect your child and the child’s safety seat against sunlight (for example you can cover it with light clothing). If the child’s safety seat is not covered, try not to expose it to the sunlight.
  Otherwise, the child safety seat may be too hot for your child’s skin.

• Never leave your child in the car unattended.

• Luggage and similar elements must be secured in order not to cause any injuries and damage in case of collision. In the event of a road accident, unsecured items may be deadly.

• You should not use the child safety seat without its fabric cover. It is an integral part of the set and influences the operation of the restraint system.

• You must not substitute the cover for a cover from another set.

• Keep the child safety seat manual. Keep it in the car in which you have installed the seat.

• If you assemble an ISOFIX child restraint system, please get familiar with the vehicle manufacturer’s manual.

• It is forbidden to use other points of contact than those described in the manual and marked on the child restraint system.

• In case of any doubts regarding the position of the safety, belts buckle for adults in relation to the main points of contact, please contact the child safety seat manufacturer.

• Att anti on – do not use a forward-facing child seat if the child’s weight does not exceed 9 kg

Safety in the car:
To provide top safety to yourself and passengers during travel, make sure:

• Folding elbow rests have been folded (vertical position).
• If the child safety seat is mounted on the passenger’s front seat, this seat is pushed to the back as far as possible.
• Any items which may cause damage to the car in case of collision have been secured properly.
• All passengers have fastened their seat belts.
  The child safety seat is suitable for installation only on forward-facing car seats. It is forbidden to mount the child safety seat on rear-facing seats/couches. They are used e.g. in vans or minibusses.

NOTE! When installed with car seat belts: never use the child safety seat with 2-point safety belts. see fi g. a,b
Correct position of the child safety seat in the car
Wrong position of the child safety seat in the car
? 1 Do not place the rearward-facing child seat here if the front airbag is active.
? 2 Assembly here is only possible if the child seat can be attached using the 3-point seat belt.

INFORMATION

NOTE
Child restraint belongs to the categories ‘universal’. Approved in accordance with UN Regulation No. 44, series of amendments 04, for general vehicle use and suitable for mounting on most car seats. Correct installation is possible if the vehicle manufacturer has stated in the vehicle’s instruction manual that the vehicle is suitable for the installation of ‘universal’ child restraints for this age group. This child restraint has been classified as ‘universal’ under more demanding conditions in relation to conditions applying to previous designs that do not have this information. In case of doubt, consult the manufacturer or the retailer of the device. Suitable for installation only if type-approved vehicles are equipped with three-point seat belts fitted with a retractor that has been approved in accordance with UN Regulation No. 16 or other equivalent standards.

Information about the ISOFIX system:
NOTE!

1. This is an ISOFIX CHILD RESTRAINT SYSTEM. It is approved in accordance with UN Regulation No. 44, 04 series of amendments for general use on vehicles equipped with ISOFIX anchorages.
2. It fits vehicles with positions approved as ISOFIX positions (according to the vehicle’s instruction manual) depending on the child seat category and attachment.
3. ISOFIX weight group and size class for which the device is intended:
   D for group 0+, I (0 – 18 kg)
   B1 for group I (9 – 18 kg)

When used for groups 0+, I, II, III – category “semi-universal”
This child restraint system is classified for use in the “semi-universal” category and is suitable for installation in the following cars:

See the user manual for a list of models. This device can also be installed in seating positions in other car models. If in doubt, consult the device manufacturer or retailer.  Rearward-facing installation: do not install the device on seats equipped with active front airbags.

CHILD SAFETY SEAT OVERVIEW

DESCRIPTION (fig. 1 and 2

A. Shoulder belts guide
B. Child safety seat cover
C. Belts protective pad
D. Shoulder belt
E. Buckle latch
F. Belts unfastening the button
G. Buckle
H. Crotch pad
I. Belt tension adjustment button
J. Belt tension adjustment
K. Seat liner
L. Seat rotation button
M. Headrest adjustment lever| N. Headrest
O. Hip belt guide
P. Seat recline handle
R. Base
S. Hip belt guide
T. Upper belts connector
U. Manual locker
W. TOP TETHER fixing belt
X. TOP TETHER fixing belt adjustment
Y. ISOFIX locking arms
Z. ISOFIX button
Z1. ISOFIX pads
---|---

HOW TO FASTEN CHILD SAFETY SEAT BELTS
To fasten belts in the child safety seat (fig. 3):

1. Connect belt buckles.
2. Insert them in the buckle (G), you will hear a distinctive „click”.
3. Make sure the belts have been tightened properly and are not twisted.

To undo the 5-point belts of the child safety seat: press the red button on the buckle (F) and loosen the belts.
HOW TO DISASSEMBLE CHILD SAFETY SEAT BELTS

1. Loosen the belts (see chapter: HOW TO ADJUST TENSION OF CHILD SAFETY SEAT BELTS).

2. Open the manual locker (U).

3. Pull out the metal connector of the belts (T) from the plastic fastener and then remove
   the belts from it (fig. 11).

4. The metal belt connector must be placed in a special spot for future use (see: fig. 10).

5. Unfasten Velcros on belt protective cushions.

6. Unfasten the child safety seat covering Velcros. Pull the buckle through the hole in the covering.

7. Fasten belts and hide them in the glovebox in the child safety seat (see: fig. 12).

Installation of belts must be performed in a reversed order.
HOW TO ADJUST HEADREST AND HEIGHT OF SHOULDER BELTS (fig. 4)
Note! The height of shoulder belts is integrated with the height of the headrest.
Groups 0, 0+ and I
To change the height of belts and headrest: loosen shoulder belts as much as you can and next grab the headrest adjustment lever (M). Choose the desired height and release the lever. Try to move the headrest to check if it has been secured properly.

Groups II and III
Slide down belts from the upper belts connector (T) located inside the manual locker (U). Pull out the child safety seat belts at the front, and put outstanding tips of belts into the protective cushions so that they do not disturb. Now you can close the locker and lift the headrest.
Hide the belt’s connector in a safe place for future use.
Position the headrest so that shoulder belts are at the child’s arms height. The belts must not be too high (at the ears level or higher), they cannot be too low either (e.g. behind the child’s back).
See fig. 5.
A – too low
B – too high
C – the perfect height for shoulder belts

HOW TO ADJUST CHILD SAFETY SEAT BELTS TENSION

1. To tighten the belts, pull the tension adjustment strap (J) (fig. 6).
2. To loosen the belts, press the adjustment button (I) and pull the shoulder belts (fig. 7).

Note! Make sure the child’s safety seat belts fit tight to the child’s body and are not twisted.
Make sure the hip belts go low and protect the child’s pelvis. The belts must fit tight the child’s body but must not be too tight and cause discomfort.
SEAT LINER
If the child needs more space in the child’s safety seat, remove the seat liner (fig. 22). It is advisable to use this liner until the child turns 1.

HOW TO REMOVE COVER

1. Remove 5-point belts of the child safety seat (see: HOW TO DISASSEMBLE CHILD SAFETY SEAT BELTS).
2. Unfasten Velcros and remove the covering from the child safety seat.
   To put the cover back on, retake the aforesaid actions in a reversed order.
   NOTE: Never use the child safety seat without the cover.
   HOW TO ROTATE THE CHILD SAFETY SEAT
   Pull the rotation key (L) and rotate the child safety seat (see: fig. 8).
   Note! After every change, make sure the child safety seat has been secured in the desired position properly and does not rotate on its own.
   During travel, the child safety seat must be in a forward- or rear-facing position. „Side” position is allowed only when you put the child in and take the child out of the seat during stopovers.
   HOW TO RECLINE CHILD SAFETY SEAT

| Groups 0, 0+, I| Group I
---|---|---
Rear-facing position| Position 5 – lying| Position 5 – lying
| Group I| Groups II, III
Forward-facing position| Position 1 – 4| Position 1 – sitting

The child safety seat can be set at five inclination angles (including one lying position when a rear-facing position is set). See fig. 9.
To recline the child safety seat, grab the handle (P) located between the seat and base, and set the desired inclination.
To set the child safety seat in a lying position, press the rotation key (L), rotate the seat by 180°, and then set the backrest in a lying position.

HOW TO ASSEMBLE THE CHILD SAFETY SEAT IN THE CAR

A. HOW TO ASSEMBLE WITH A CAR SAFETY BELT
GROUP 0 (0 – 13 kg)
For this weight group, the child safety seat is mounted in a rear-facing position, in a lying position. For instructions on how to adjust the child safety seat inclination, see: HOW  TO RECLINE CHILD SAFETY SEAT.
See: fig. 13

1. Place the child’s safety seat on the car seat.
2. Pull the car safety belt and pull the hip part under the seat liner (K) through the hip belt guide (O).
3. Pull the shoulder part of the car safety belt through the shoulder belt guide (S).
4. Fasten the belt, tighten it as much as you can, and make sure it is not twisted. Press the child safety seat against the car seat.
5. Put the child in it.
   After you have completed the assembly, make sure the belts have been carried through the guides properly and have been fastened correctly. To do so, try to move the child’s safety seat and check if it is stable.

GROUP I (9 – 18 kg) See: fig. 14.
For this weight group, the child safety seat is mounted in a forward-facing position, in positions 1-4.

1. Place the child’s safety seat on the car seat.
2. Pull the shoulder part of the car belt through the shoulder belt guide (S).
3. Pull the hip part of the car belt through the hip belt guide (O).
4. Pull the shoulder belt behind the child safety seat backrest through the third guide (O).
5. Fasten the child safety seat.
6. Press the child safety seat against the car seat and pull the car belt as much as you can.
7. Put the child in it.
   After you have completed the assembly, make sure the belts have been carried through the guides properly and have been fastened correctly. To do so, try to move the child’s safety seat and check if it is stable.
   GROUPS II and III (15 – 36 kg)
   For these weight groups, you have to disassemble 5-point belts of the child safety seat. The child safety seat must be mounted in a forward-facing position.

See fig. 15.

1. Place the child’s safety seat on the car seat, and put the child in it.
2. Pull the shoulder belt of the car through the shoulder belt guide (A) on the headrest.
3. Pull the hip part of the car belt through the hip belt guide (O) at the seat. Carry the shoulder belt through the same guide.
4. Fasten the belts.
5. Tighten the car belt.
   Make sure the shoulder part goes through the child’s collarbone, not its neck. The hip part must be as low as possible in relation to the child’s hip.

B. HOW TO ASSEMBLE WITH ISOFIX SYSTEM AND TOP TETHER OR ISOFIX, TOP
TETHER + CAR SEAT BELTS
GROUPS 0, I (0 – 18 kg)
Installation in a rear-facing position.
See fig. 16 and 17.

1. Place the child’s safety seat on the car seat.
2. If necessary, put both ISOFIX pads (Z1) on the fixing points of your car. Press ISOFIX buttons (Z) to pull out the connecting arms (Y). Pull them out as far as possible and then connect to the fixing points of your car. After you have heard a „click”, press the child safety seat against the car seat. ISOFIX latch indicators should be green on both ISOFIX arms (fig. 16).
3. Pull TOP TETHER fixing belt out and next extend it with the use of the adjustment (X).
   Fasten the handle in the spot suggested in the vehicle manual (see: fig. 17). Tighten TOP TETHER with the use of the adjustment (X). The upper fixing belt is properly
   tightened when you can see a green indicator in the buckle.

Note – the upper belt fastening point can differ, depending on the car. Figure 17 shows examples of fixing, depending on the car model.

GROUP I (9 – 18 kg)
Installation in a forward-facing position.

1. Place the child’s safety seat on the car seat.
2. If necessary, put both ISOFIX pads (Z1) on the fixing points of your car. When you can hear a „click”, press the child safety seat against the car seat as much as you can.  Press ISOFIX buttons (Z) to pull out the connecting arms (Y). Pull them out as far as you can, and then connect to the fixing points of your car. ISOFIX latch indicators  should be green on both ISOFIX arms (fig. 18)
3. Pull TOP TETHER fixing belt out and next extend it with the use of adjustment (X).
   Fasten the handle in the spot suggested in the vehicle manual (see: fig. 19). Tighten TOP TETHER with the use of the adjustment (X). The upper fixing belt is properly
   tightened when you can see a green indicator in the buckle.
   Note – the upper belt fastening point can differ, depending on the car. Figure 19 shows examples of fixing, depending on the car model.

GROUPS II, II (15 – 36 kg)
For these weight groups, you have to disassemble 5-point belts of the child safety seat.
Mount the child safety seat in a forward-facing position.

1. Place the child’s safety seat on the car seat.
2. Put both I
3. SOFIX pads (Z1) on the fixing points of your car. Press ISOFIX buttons (Z) to pull out the connecting arms (Y). Pull them out as far as you can, and then connect to the fixing points of your car. The latch indicator should be green.
   Next, take one of the steps below – a or b. Installation with ISOFIX handles only is prohibited!

A. ISOFIX + car belts (see: fig. 20).

1. Place the child in the child’s safety seat.

2. Pull the car safety belts.

3. Carry the shoulder belt through the shoulder belt guide (A) and the hip belt through the hip belt guide (O).
   Make sure the shoulder belt goes through the child’s collar, not its neck.

4. Fasten car safety belts.

5. Tighten car safety belts. the step described in „a” concerning assembly with car belts. Make sure the shoulder belt goes t

B. ISOFIX + TOP TETHER + car belts

1. Take through the child’s collar, not its neck.
2. Pull out TOP TETHER fixing belt and next extend it with the use of adjustment (X).
   Fasten the handle in the spot suggested in the vehicle manual (see: fig. 19). Tighten TOP TETHER with the use of adjustment (X). The upper fixing belt is properly tightened when you can see a green indicator in the buckle.

HOW TO MAINTAIN AND CLEAN

You can clean the cover in warm water with soap or soft detergent. Do not dry the cover in the sun. Clean the buckle, child safety seat belts, and plastic elements with warm water. Do not use strong detergents. If you do not use the product, store it in a dark and dry place, away from sunlight.
The pictures are for reference only. The real design of the products may differ from the pictures presented.
The product has been tested and meets all the requirements of the: ECE R44.04

Detailed warranty conditions are available on the website: www.lionelo.com
Thank you for purchasing our product

www.lionelo.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>