lionelo Bastiaan One Baby car seat User Manual

User manual
Basti aan One
Baby car sea

www.lionelo.com

NOTICE
When using groups 0+, I, II, and III, the „universal” category: The child restraint system is categorized as „universal”. It has been granted a certificate of approval in accordance with regulations no. 44, amendments series 04, for general use in vehicles and is fit for installation on most car seats.
A proper installation is possible if the vehicle manufacturer has declared in the vehicle manual that this vehicle is fit for installation of the child restraint system in the „universal”  category for this age group.
This child restraint system has been classified as „universal” in more demanding conditions than conditions applicable in previous designs not supplied with this information.
In case of any doubts, please consult the manufacturer or retailer of the device.

When using for groups 0+, I, II, III, the „semi-universal” category”:
This child restraint system has been classified for use in „semi-universal” categories and is fit for installation on seats in the following cars:

The model list is at the end of the user manual.
This device may be fit for installation also on seats of other car models. In case of any doubts, please consult the manufacturer or retailer of the device. It is fit for installation only when certified vehicles are equipped with three-point safety belts with retractor which have been granted a certificate of approval in accordance with the regulations  UN/ECG no. 16 or other equivalent standards. If assembled in a rear-facing position: do not assemble the child safety seat on seats equipped with airbags.

As for ISOFIX installation:
NOTE

1. It is ISOFIX CHILD RESTRAINT SYSTEM. It has been granted a certificate of approval in accordance with regulations no. 44, amendments series 04 for general use in vehicles equipped with the ISOFIX system.
2. It fits vehicles with positions approved as ISOFIX positions (pursuant to the vehicle operating manual), depending on the child safety seat category and fixing.
3. ISOFIX weight group and size class the device is intended for: D (groups 0+, I)

Dear customer!
Before you use the child safety seat for the first time, please read this manual carefully.
Should you have any remarks or questions concerning the product, please do not hesitate to contact us: help@lionelo.com

The product is allowed for ECE R44/04 as the safety seat for weight categories 0+, I, II, and III (0-36kg).
A failure to follow the manual may lead to accidents. The product must always be used and installed in the way described in this manual.

Producer:
BrandLine Group Sp. z o. o.
ul. A. Kręglewskiego 1, 61-248 Poznań, Poland
IMPORTANT
Please read this manual before the first use and keep it. The manual provides a description of how to assemble the safety seat properly. An unsuitable assembly may pose a  threat to a child’s heath. The manufacturer shall not be held responsible for potential hazards caused by unsuitable assembly of the safety seat.

1. This safety seat is intended for weight categories (groups) 0+, I, II
   I III, which means that it can be used by children whose weight does not exceed 36 kg (aged up to 11).
   0+ weight group: 0-13kg
   I weight group: 9-18kg
   II weight group: 15-25kg
   III weight group: 22-36kg

2. The safety seat is intended for vehicles equipped with 3-point safety seats are granted a certificate of approval in accordance with Regulations no. 16 ECG/UN or other equivalent standards.

3. Applies to rear-facing installations only: Do not place the safety seat on the front passenger’s seat when the passenger’s airbag is active.

4. All safety seat belts must be tight, adapted to the child’s body, and must not be twisted.

5. All lap belts must be carried low so that the child’s pelvis is properly supported.

6. Buckles must be done up properly and securely. In case of emergency, a proper assembly of buckles lets you take the child out of the safety seat easily.

7. The device must be replaced if subject to rapid loads during an accident.

8. Do not modify the product in any way.

9. Avoid situations in which the safety seat is exposed to direct sunlight. Otherwise, it may heat up and in effect cause the child to scald itself.

10. Do not leave the child in the safety seat unattended. Make sure the luggage and other items which may lead to injuries in case of the accident have been secured.

11. Do not use the safety seat without a material cover. Do not replace the cover with other than recommended by the manufacturer. The cover is an integral part of the safety seat.

12. The safety seat must be used in the car only.

13. It is forbidden to place any items on the child’s safety seat.

14. Hard elements and plastic parts of the child holding device must be placed and installed in a way that they are not trapped by a movable seat and vehicle door during regular operation of the vehicle.

15. Before every travel, make sure the safety seat has been properly and securely mounted.

16. During travel, the safety seal must be properly attached to the car’s seat by means of the car safety belt or ISOFIX and Top Tether, even when there is no child.

17. Do not use load-bearing points of contact other than those described in the instructions and marked on the child restraint

18. For rearward facing installation: do not install the child seat on seats with airbags.

19. Install the rearward-facing seat if the child weighs less than 9 kg

20. If in doubt about the position of the adult seat belt buckle in relation to major load-bearing contact points, contact the manufacturer.

CAUTION!
Never use the safety seat with 2-point seat belts (fig. 1). fig. 2
Suitable position of the safety seat in the car
Not suitable position of the safety seat in the car
?1 Place the safety seat facing forward. Do not place the safety seat on the passenger’s front seat when the passenger’s airbag is active
?2 Installation is possible only if three-point seat belts and ISOFIX anchorages are present.
SAFETY SEAT OUTLINE (fig. 3)

1. Belt guide
2. Safety seat cover
3. Arm pad
4. Shoulder belt
5. Buckle clasp
6. Red button
7. Buckle
8. Crotch pad
9. Reduction pad
10. Belt tension adjustment button
11. Tension adjustment belt
12. Rotation button| 13. Headrest height adjustment
14. Headrest
15. Red and blue belt guide
16. Tilting handle
17. Base
18. ISOFIX overlays
19. Buckle
20. Upper fastening belt TOP TETHER
21. ISOFIX button
22. Belt adjustment
23. ISOFIX arms
---|---

SAFETY SEAT BELTS

To fasten belts in the safety seat (fig. 4):

1. Connect belt clasps together.
2. Make sure the connection is proper
3. Insert them into the fastening, you will hear a distinctive click.
4. Make sure the belts have been properly tightened and are not twisted. To undo the belts, press the red button.
5. After undoing the seat belts, you can put them in special hooks located on the side of the seat.

To disassemble 5-point belts of the safety seat (fig. 5):

1. Press the red button and loosen the belts.
2. Remove the loose belts from the connectors in the back of the safety seat.
3. Take the belts from the safety seat through the holes.
4. Remove arm pads.
5. Roll up shoulder belts and place them in the safety seat holes (fig. 6).
6. Loosen the crotch belt, take the buckle located under the safety seat and remove the belt. Pull the crotch belt and pull through the hole (fig. 7, 8).
   To assemble the belts again, retake the actions above in reversed order. Make sure the belts have been properly inserted in the buckles and are not twisted (fig. 9).

Safety seat belts tension adjustment

1. Make sure the safety seat belts fit tight to the child’s body and are not twisted.
2. To tighten the belts, pull the shoulder belts upwards and pull the tension adjustment belt at the same time (fig. 10).
3. To loosen the belts and adjust their length, press the button between the child’s legs and pull the shoulder arms. Make sure you pull the belts, not shoulder pads (fig. 11).

Safety seat belts height adjustment (fig. 12)

1. A suitable belt height assures increased comfort and safety for your child. The height must be adapted in a way that two fingers fit between the child and the belts.
2. To adjust the height, loosen the bolts and remove them from the buckles in the back of the safety seat.
3. Take the shoulder belts out through the safety seat holes and insert them in holes at relevant heights.
4. Assemble the belts in buckles again.

REMOVING COVER

1. Remove 5-point belts from the safety seat.
2. Remove the cover from the base and backrest.
3. Set the top position of the headrest.
4. Remove the cover.
   To apply the cover again, retake the aforesaid actions in reversed order.
   NOTE: Never use the safety seat without the cover

SAFETY SEAT INCLINATION (fig. 13)
To incline the safety seat, grab the handle located between the safety seat and base, and set it in a required position.
To adjust the lying position, press the rotation button, turn the safety seat by 180°, and then set the lying position of the backrest.
SAFETY SEAT ROTATION (fig. 14)
Before rotating the seat, loosen TopTether. To rotate the safety seat, press the rotation button and rotate the safety seat.
CAUTION: Before travel, make sure the safety seat has been locked and cannot rotate on its own.

HEADREST HEIGHT (fig. 15)
The headrest must be positioned at a height that assures that shoulder belts are at the height of the child’s shoulders.
A. TOO LOW B. TOO HIGH C. OK

To adjust the headrest height, pull the adjustment handle along with the headrest. To adjust the headrest to a higher position: loosen the straps, undo the fastening buckle on the  back of the seat (detail 19 in fig. 3) (fig. 16)

HOW TO ASSEMBLE A SAFETY SEAT IN THE CAR

1. Rear-facing position with seat belts (group 0+)
   a. Rotate the seat by 90 degrees. Grab the inclination adjustment lever and incline the seat as far as you can (fifth level – „half-lying”). Rotate the seat again so that it is in a  rear-facing position.
   b. Position the child safety seat on the car seat in a rear-facing position.
   c. Pull the seat belt and carry the shoulder part at the back of the child safety seat. The belt must go through the part between the headrest and backrest (fig. 18).
   d. Carry the hip part of the seat belt through the guide in the child safety seat (marked as 15 in fig. 3) and then under-seat liner (fig. 18).
   e. Fasten the belts. Press the child safety seat against the car seat.
   Tighten the belt as shown by arrows in figure 18.
   f. Move the child safety seat to check if it has been securely fixed. If the product fixing is unstable, adjust the belt tension.
   g. Put the child in the child’s safety seat and fasten its safety belts.

2. Rear-facing position with ISOFIX and TOP TETHER (groups 0+, I)
   a. Rotate the seat by 90 degrees. Grab the inclination adjustment lever and incline the seat as far as possible (fifth level – „half-lying”). Rotate the seat again so that it is in a  rear-facing position.
   b. If necessary, put ISOFIX covers on ISOFIX connectors in the car. They help you stick ISOFIX fasteners when the car connectors are hard to access.
   c. Position the child safety seat on the car seat in a rear-facing position.
   d. Press the ISOFIX button to pull out both ISOFIX arms. Grab the child safety seat and slide two ISOFIX arms into fasteners located in the car seat until they engage and you can hear a distinctive „click” (fig. 19).
   e. Push the child safety seat against the car seat as far as you can. The marker on both sides of ISOFIX arms should turn from red to green.
   f. Pull out TOP TETHER fixing belt and unroll it with the use of an adjustment device (fig. 20).
   g. Fasten the TOP TETHER belt in the spot recommended in the vehicle manual. The upper belt fastening spot may differ, depending on the car model (fig. 21). Tighten the TOP TETHER fixing belt so that a green marker shows up on the buckle. h. Put the child in the child’s safety seat and secure it with its safety belts.

3. Forward- acing position with seat belts or seat belts and ISOFIX connectors (group
   I) ISOFIX (optional)
   a. If necessary, put ISOFIX covers on ISOFIX connectors in the car.
   They help you stick ISOFIX fasteners when car connectors are hard to access.
   b. Position the child safety seat on the car seat in a forward-facing position.
   c. Press the ISOFIX button to pull out both ISOFIX arms. Grab the child safety seat and slide both ISOFIX arms into fasteners located in the car seat until the arms engage and you can hear a distinctive „click” (fig. 22).
   d. Push the child safety seat against the car seat as far as you can. The marker on both sides of ISOFIX arms should turn from red to green. CAR SEATS (required)
   Fig. 23
   1 – make sure this belt goes behind the headrest, under-seat liner, just by the child safety seat backrest.
   2 – make sure this belt goes under the seat liner.
   a. Position the child safety seat on the car seat in a forward-facing position.
   b. Pull the car seat and carry its shoulder part between the headrest and backrest of the child safety seat (fig. 23).
   c. Carry the hip part of the car seat along the child safety seat backrest and then through the guide (marked as 15 in fig. 3) (fig. 23).
   d. Fasten the belts. Press the child safety seat against the car seat.
   Tighten the belts as shown by arrows in figure 23.
   e. Move the child safety seat to check if it has been securely fixed. If fixing the child safety seat is unstable, adjust belt tension.
   f. Put the child in the child’s safety seat and secure it with its safety belts.

4. Forward-facing position with seat belts or seat belts and ISOFIX connectors or seat belts, ISOFIX connectors, and TOP TETHER (groups II, III)
   Important: for this group disassemble 5-point safety belts. The child must be secured with a car seat belt. ISOFIX (optional)
   a. If necessary, put ISOFIX covers on ISOFIX connectors in the car.
   They help you stick ISOFIX fasteners when car connectors are hard to access.
   b. Position the child safety seat on the car seat in a forward-facing position.
   c. Press the ISOFIX button to pull out both ISOFIX arms. Grab the child safety seat and slide two ISOFIX arms into fasteners located in the car seat until they engage and you can hear a distinctive „click”.
   d. Push the child safety seat against the car seat as far as you can.
   The marker on both sides of ISOFIX arms should turn from red into green (fig. 24a). TOP TETHER (optional)
   a. Pull out TOP TETHER fixing belt and unroll it with the use of an adjustment device (fig. 24a).
   b. Fasten TOP TETHER in the spot recommended in the vehicle manual.
   The upper belt fastening spot may differ, depending on the car model (the example of the location of fastening spots has been shown in the example of group 0+ in fig.  21).
   c. Fasten TOP TETHER fixing belt so that a green indicator shows up on the buckle

CAR SEAT BELTS (required)
a. Position the child safety seat on the car seat in a forward-facing position.
b. Put the child in the child’s safety seat.
c. Pull the car seat belt and carry its shoulder part through the belt guide in the headrest (element marked as 1 in fig. 3).
d. Carry the hip part of the car seat belt through the guide (marked as 15 in fig. 3) (fig. 24b).
e. Fasten the belts. Press the child safety seat against the car seat.
Tighten the belts as shown by arrows in figure 24b. Make sure they are not too tight and do not limit the child.
f. Move the child safety seat to check it has been securely fixed. If the fixing of the product is unstable, adjust the belt tension.

Make sure the shoulder belt goes between points marked in fig. 24B as a and b, that is between the child’s neck and arm
HOOD ASSEMBLY (fig. 25, 26)

1. Pull the hood over the headrest of the seat
2. Hook the mounting bands on the plastic element of the headrest, as in the picture below.

MAINTENANCE AND CLEANING

1. Check for any damage to the safety seat on a regular basis. In case of any irregularities, replace the safety seat immediately.
2. Make sure the safety seat is not exposed to direct sunlight.
3. Covers may be cleaned in warm water with soap or a soft detergent. Do not dry the covers in the sun.
4. Clean a clasp, safety seat belts, and plastic elements with warm water. Do not use any detergents.

The pictures are for reference only. The real design of the products may differ from the pictures presented.
The product has been tested and meets all the requirements of the: ECE R44.04

Detailed warranty conditions are available on the website: lionelo.com
Thank you for purchasing our product

www.lionelo.com

References

• Lionelo.com - Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>