Nedis RDFM4000WT FM Radio User Manual
- June 5, 2024
- nedis
Table of Contents
RDFM4000WT FM Radio
User Manual
Preface
Thank you for purchasing the Nedis RDFM4000WT.
This document is the user manual and contains all the information for correct, efficient and safe use of the product.
This user manual is addressed to the end user. Read this information carefully before installing or using the product.
Always store this information with the product for use in the future.
Product description
Intended use
The RDFM4000WT is an FM radio with 30 preset radio stations that can be mounted under a cabinet to save valuable workspace.
The product is equipped with clock, alarm, stopwatch and countdown functions.
This product is not intended for use by persons (including children) with a reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the product by a person responsible for their safety.
The product is intended for indoor use only.
The product is not intended for professional use.
Any modification of the product may have consequences for safety, warranty and proper functioning.
Specifications
Product
|
FM Radio
---|---
Article number
|
RDFM4000WT
Dimensions (w x h x d)
|
245 x 48 x 120 mm
Weight
|
544 g
Power input
|
220 – 240 VAC ; 50 Hz
Rated power
|
5 W
Battery type
|
3 VDC (2 x AA) (not included)
Radio bands
|
FM
FM frequency range
|
87.5 – 108 MHz
Preset stations
|
30
Connections
|
3.5 mm audio input and output
Main parts (image A)
A
1. Mounting bracket
2. FM antenna
3. Battery compartment
4. Stands
5. Mode button
6. Power button
7. Volume wheel
8. Function button
9. Set button
10. LCD display
11. Buzzer mode indicator
12. Radio mode indicator
13. Power cable
14. 3.5 mm audio output
15. 3.5 mm audio input
16. Memory down button
17. Memory up button
18. Tune wheel
19. Alarm button
20. Snooze / sleep button
21. Assembly template
22. Screws
Safety instructions
WARNING
- Only use the product as described in this manual.
- Read the manual carefully before use. Keep the manual for future reference.
- Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
- Do not drop the product and avoid bumping.
- This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.
- Disconnect the product from the electrical outlet and other equipment if problems occur.
- Do not expose the product to water or moisture.
- Disconnect the product from the power source before service and when replacing parts.
- Children should be supervised to ensure that they do not play with the product.
- The power cable cannot be replaced. If the cable is damaged the product should be scrapped.
- Secondary cells and batteries need to be charged before use. Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions.
- After extended periods of storage, it may be necessary to charge and discharge the cells or batteries several times to obtain maximum performance.
- Battery usage by children should be supervised.
- Remove the batteries if you do not use the product for an extended period of time.
- Unplug the product if you do not plan on using the product for an extended period of time.
- Do not use the product near water.
- Do not expose the product to direct sunlight, naked flames or heat.
- When the product is not used for an extended period, store the product in a dry place away from sunlight and protect it against excessive dust and dirt.
- Do not open the product. There are no user serviceable parts inside.
- Do not put hands and foreign objects inside the product.
- Keep the product away from magnetic or magnetized objects.
- Extended exposure to high volumes can cause hearing loss.
Safety symbols on the product
Icon
|
Description
---|---
|
Electronic equipment needs to bear the CE mark in order to be marketed in the EU. CE marking shows that a product is assessed before being placed on the market and that it meets EU safety, health and environmental protection requirements. CE marking is also sometimes accepted as a means of compliance with type-approval requirements; for example, electronic components that require type-approval and also CE marking for electromagnetic compatibility (EMC) or low-voltage equipment.
|
Product in which protection against electric shock does not rely on basic insulation only, but in which additional safety precautions such as double insulation or reinforced insulation are provided, there being no provision for protective earthing or reliance upon installation conditions NOTE A Class II products may be provided with means for maintaining the continuity of protective circuits, provided that such means are within the product and are insulated from accessible surfaces according to the requirements of Class II.
|
Indication to explain the product is suitable for indoor use only.
|
Indication to warn for electric shock.
|
Indication to explain that the product needs to be collected separately when disposed. Do not throw in the trash bin.
Installation
- Check the contents of the package
- Check that all parts are present and that no damage is visible on the parts. If parts are missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.
Installing the product on a flat surface
1. Unfold the stands A 4.
2. Place the product on a flat surface close to a power outlet.
Installing the product under cupboard (image B, C, D)
|
---|---
B
|
C
D
- The cupboard floor thickness should be at least 16 mm.
Install the product close to a power outlet.
- Use a screwdriver to fix the screws.
- Do not plug the power cable A13 into the power outlet during the installation.
- Do not use any accessories that are not included.
- Do not install the product under a cupboard with a lighting strip installed underneath.
- Do not install the product above places were steam and water can get in contact with the product.
Inserting the batteries (image E)
E
1. Open the battery compartment A 3.
2. Insert 2 AA batteries.
- Make sure to match the (+) and (-) polarity markings.
3. Close A 3.
- Connecting the product to a power source
- Plug the power cable A13 into the power outlet.
Use
Switching on the product
- Press the power button A 6 to switch on the product.
- Press A 6 while the product is switched on to switch to standby mode.
- In standby mode the time and date are shown on the LCD display A10.
- The display is automatically dimmed between 23:00 – 05:00 h
Controlling the product
- Rotate the volume wheel A 7 to adjust the volume to the desired sound level.
- Rotate the tune wheel A18 to adjust values and press the set button A 9 to confirm a setting.
- Rotate and hold A18 to rapidly advance or reverse values.
Setting the clock
1. Switch the product to standby mode.
2. Press A 9.
3. Set the current minutes and confirm.
4. Set the current hours and confirm.
5. Set the clock to 24 hour or 12 hour setting and confirm.
Setting the calendar
1. Switch the product to standby mode.
2. Press the mode button A 5.
- The month, day and year appear on A10.
3. Press A 9.
4. Set the current day and confirm.
5. Set the current month and confirm.
6. Set the current year and confirm.
Setting the alarm
1. Switch the product to standby mode.
2. Press the alarm button A19 once. ALM 1 appears on A10.
3. Press A19 again. ALM 2 appears on A10.
4. Select the buzzer mode indicator A12 or the radio mode indicator A11 and confirm.
5. Set the minutes and confirm.
6. Set the hours and confirm.
7. In radio mode, press A 9 again to continue and select a radio station.
- When the alarm goes off, press any button to switch off the alarm.
8. Press the snooze / sleep button A20 to delay the alarm sound, the alarm sound resumes after 5 minutes.
Controlling the music
1. Switch on the product.
2. Press the function button A 8 to select radio or AUX function.
- In radio mode the current radio frequency appears on A10.
3. Tune to a desired FM station or rotate and hold A18 to start the automatic scanning for the next available radio station.
4. In AUX mode, connect an external audio source to the 3.5 mm audio input A15 to play external audio.
- The product automatically switches to standby after 10 minutes without a signal.
Saving radio presets
1. In radio mode, press A 9.
2. Select a preset number with the memory up button A17 or the memory down button A16 and confirm to save the current radio station.
Setting the timer
1. Press A 8 1 time. TMR appears on A10.
2. Press A 9.
3. Set the seconds and confirm.
4. Set the minutes and confirm.
5. Rotate A18 clockwise to start the timer.
- When the timer runs out, a signal tone sounds for about 1 minute.
- When the timer goes off, press any button to switch off the sound.
Setting the stopwatch
1.Press A 8 2 times. STW appears on A10.
2. Rotate A18 clockwise to start the stopwatch.
3. Rotate A18 clockwise again to stop the stopwatch.
4. Rotate A18 counterclockwise to reset the stopwatch.
Using sleep function
- In sleep mode, the radio plays until the timer runs out.
- The remaining time appears on A10.
- Press A20 to change the remaining time in steps of 10 minutes.
Maintenance
- Clean the product regularly with a soft, clean, dry cloth. Avoid abrasives that can damage the surface.
- Do not use aggressive chemical cleaning agents such as ammonia, acid or acetone when cleaning the product.
- Do not open the product.
Warranty
Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.
Disclaimer
Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.
Disposal
|
This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.
---|---
Declaration of Conformity
We, Nedis B.V. declare as manufacturer that the product RDFM4000WT from our brand Nedis®, produced in China, has been tested according to all relevant CE standards and regulations and that all tests have been passed successfully. This includes, but is not limited to the RED 2014/53/EU regulation.
The complete Declaration of Conformity (and the safety datasheet if applicable) can be found and downloaded via webshop.nedis.com/rdfm4000wt#support
For additional information regarding the compliance, contact the customer service:
Web: www.nedis.com
E-mail: service@nedis.com
Phone: +31 (0)73-5991055 (during office hours)
Nedis B.V., de Tweeling 28
5215 MC ’s-Hertogenbosch, the Netherlands
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>