BEGA 51 283.4 Pendant Luminaire System Instruction Manual

: June 4, 2024
: BEGA

Table of Contents

BEGA 51 283.4 Pendant Luminaire System
Product Information
Product Usage Instructions
FAQ
Dimensions
Instructions for use
Product Description
Safety
Installation
Cleaning Maintenance
Accessories
Documents / Resources

BEGA 51 283.4 Pendant Luminaire System

BEGA-51-283.4-Pendant-Luminaire-System-PRODUCT

Product Information

Specifications

Lamp Module connected wattage: 13.6 W
Luminaire connected wattage: 16.3 W
Colour temperature: 3000 K
Colour rendering index (CRI): > 90
Module luminous flux: 2150 lm
Luminaire luminous flux: 1866 lm
Luminaire luminous efficiency: 114.5 lm /W
Rated temperature: 25°C
Ambient temperature: 30°C

Product Usage Instructions

Safety Information

The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should carry out installation and commissioning.
The manufacturer is not liable for damage due to improper use or installation. Any modifications made to the luminaire should be done by a qualified person.

Operating Requirements

The luminaire must be operated with an operating device that meets the requirements of EN 61347-2-13.
The maximum idle voltage should not exceed 60 V DC and must conform to SELV or SELV equivalent standards.

Installation Tips

LED components are sensitive; avoid touching the light output opening directly during installation or relamping to prevent damage.

Additional Components

To operate this luminaire, one of the specified BEGA Installation components must be ordered separately.
Refer to the instructions for the selected BEGA installation component for proper luminaire installation.

FAQ

Q: Can the luminaire be operated without the specified BEGA installation component?

A: The manufacturer does not accept liability for damage caused by improper use or installation if the BEGA installation component is not used.

Q: What should I do if I need spare parts for the LED module?

A: You can order a synthetic cover with the part number 75 005 978 for the LED-1418/930 module with a colour temperature of 3000 K.

Dimensions

BEGA-51-283.4-Pendant-Luminaire-System-FIG-1

Instructions for use

Application

Pendant luminaire · Indoor luminaire for unshielded and uniform light, with synthetic cover, translucent white and metal housing.
BEGA System pendant luminaire for use in combination with various modular BEGA installation components.

Product Description

Metal housing, finish colour matt brass Synthetic cover, translucent white
Cable pendant · Sheath cable white 2 x 0,75@ Overall length of luminaire approx. 2000 mm Safety class III
Conformity mark
Weight: 0.9 kg
This product contains light sources of energy efficiency class(es) D

Luminaire without canopy,

for connection to an additional required BEGA Installation component (accessory)

Lamp

Module connected wattage 13.6 W
Luminaire connected wattage 16.3 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 30 °C

51 283.4 K3

Module designation LED- 1418/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 2150 lm
Luminaire luminous flux 1866 lm
Luminaire luminous efficiency 1 14,5 lm / W

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Please note:

The luminaire can only be operated with an operating device that fulfils the requirements according to EN 61347-2-13. The maximum idle voltage of 60 V DC must conform to SELV or SELV equivalent.

Installation

LEDs are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
To operate this luminaire one of the following additional BEGA Installation components must be ordered – accessories. Please refer to the instructions for use for the BEGA installation component selected for luminaire installation

Please note:

The manufacturer accepts no liability for damage caused by improper use or installation if no BEGA installation component is used to install this BEGA system pendant luminaire.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system from the power supply. Loosen the canopy/canopy cover and push it downward on the luminaire cable.
Remove the connecting wires of the luminaire cable from the terminals in the canopy. Unhook the pendant luminaire.
Dismantle the coaxial line connector and remove the lower part of the connector via the luminaire cable.
Remove the strain reliever from the luminaire hanger.
Loosen the knurled nut and remove the strain reliever via the luminaire cable.
Remove the canopy/canopy cover.
Undo the knob in the funnel-shaped upper part of the housing by turning anti-clockwise. Remove the knob and upper part of the housing via the luminaire cable.
Detach the synthetic cover and remove it via the luminaire cable.
Loosen the outer 2 Torx screws (T 10) of the housing tube.
Remove the connecting wires of the LED module strip from the terminals and remove the housing tube complete with the LED module
(module strip) via the luminaire cable.
Guide the replacement LED module (housing tube with module strip) over the luminaire cable.
Please follow the installation instructions for the new LED module.
Fasten the housing tube with the LED module strip onto the luminaire base using 2 Torx screws (T 10).
Guide the synthetic cover over the luminaire cable onto the luminaire base.
A defective luminaire cover must be replaced.
Guide the funnel-shaped upper part of the housing and knob over the luminaire cable onto the synthetic cover and tighten the knob in a clockwise direction.
IMPORTANT: The luminaire cable must first be guided through the borehole on the underside of the canopy.
Install the strain reliever and coaxial line connector back onto the luminaire cable.
Clip the strain reliever into the luminaire hanger and hook the pendant luminaire into the canopy.
Connect the wires of the luminaire cable (red to “+” and black to “-“) back onto terminals in the canopy.
Attach the canopy/canopy cover to the ceiling.
Fine adjustment of the pendant luminaire Undo the knob in the funnel-shaped upper part of the housing by turning it anti-clockwise to enable the fine adjustment of the pendant luminaire along its horizontal axis.
Hold the bottom edge of the pendant luminaire with one hand and simultaneously turn the synthetic cover along its vertical axis with the other hand until the luminaire body is aligned horizontally.
Tighten the knob in the funnel-shaped upper part of the housing by turning it in a clockwise direction.

Cleaning Maintenance

Clean the luminaire regularly with solvent-free cleaning agents to remove dirt.
A defective synthetic cover must be replaced.

Accessories

BEGA Installation components with LED power supply unit.
Satin white finish.
Depending on the desired type of installation, the following suitable installation components are available for this BEGA system pendant luminaire:

For all level ceilings:

13 238 Surface-mounted canopy (Type A)
DALI · 220-240 V · 490 mA DC
13 266 Surface-mounted canopy (Type AS)
Smart controllable/dimmable 220-240 V · 490 mA DC
Suitable for level ceilings and sloped ceilings with a pitch of 0 – 40°:
13 244 Surface-mounted canopy (Type B) DALI · 220-240 V · 490 mA DC
13 250 Recessed canopy (Type C) DALI · 220-240 V · 500 mA DC
13 272 Recessed canopies (Type CS) Smart controllable/dimmable ·
220-240 V · 500 mA DC
For flush and surface-mounted 3-phase Eurostandard-Plus® track systems: 13 218 Track adapter (Type D) DALI · 220-240 V · 500 mA DC
For the accessories, separate instructions for use can be provided upon request.

Spares

LED module 3000 K LED-1418/930
Synthetic cover 75 005 978
BEGA Gantenbrink-Leuchten KG
Postfach 31 60 · 58689 Menden
info@bega.com
www.bega.com

Documents / Resources

| BEGA 51 283.4 Pendant Luminaire System [pdf] Instruction Manual
51 283.4, 51 283.4 Pendant Luminaire System, Pendant Luminaire System, Luminaire System, System
---|---