BEGA 51295.5K3 Wall and Ceiling Light Instruction Manual

: June 4, 2024
: BEGA

Table of Contents

BEGA 51295.5K3 Wall and Ceiling Light
Product Usage Instructions
Instructions for use
Product Description
DIMENSION
Safety
SPECIFICATION
Installation
Cleaning Maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 51295.5K3 Wall and Ceiling Light

BEGA-51295-5K3-Wall-and-Ceiling-Light-PRODUCT

Product Specifications

Lamp Module connected wattage: 11.5 W
Luminaire connected wattage: 13.2 W
Rated temperature: 25-40°C
Ambient temperature: max 25-40°C
Colour temperature: 3000 K
Colour rendering index (CRI): >90
Module luminous flux: 1800 lm
Luminaire luminous flux: 965 lm
Luminaire luminous efficiency: 73.1 lm/W

Product Usage Instructions

Safety Instructions
The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should carry out the installation and commissioning. The manufacturer is not liable for damage due to improper use or installation. Any modifications should be done by the responsible person and considered as the manufacturer’s responsibility.

Overvoltage Protection
The electronic components in the luminaire are protected against overvoltage as per DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website.

Replacing the LED Module
To replace the LED module, note the module designation on the label inside the luminaire. BEGA replacement modules match the original ones in terms of light color and output. Qualified individuals can replace the module using standard tools after disconnecting the system from the power supply.

FAQ

Q: Can I replace the LED module myself?
A: Yes, qualified persons can replace the LED module using standard tools after disconnecting the power supply.
Q: Where can I find overvoltage protection components?
A: Overvoltage protection components can be found on the manufacturer’s website at www.bega.com.

Instructions for use

Application

Ceiling and wall luminaire · Indoor luminaire with synthetic cover, white interior, for a host of lighting applications.
Ideal for use in corridors, passageways, and functional rooms.

Product Description

Ceiling and wall luminaire
Luminaire housing made of synthetic material, finish color velvet black
Transparent synthetic cover, white interior
Two elongated mounting holes
Width 4.8 mm · 160 mm spacing
2 cable entries for through-wiring the connecting cable 7-10.5 mm in diameter, max. 3 G 1.5@
Connection terminal 2.5@
Earth conductor connection
Complies with flicker requirements by IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V x 0/50-60 Hz
DC 170-276 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
– Conformity mark
Weight: 1.5 kg
This product contains light sources of energy efficiency class(es) D

DIMENSION

$BEGA-51295-5K3-Wall-and-Ceiling-Light-FIG- $1$$

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

SPECIFICATION

Lamp

Module connected wattage 11.5 W
Luminaire connected wattage 13.2 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 40 °C

51 295.5 K3

Module designation LED-1286/930
Color temperature 3000 K
Color rendering index CRI > 90
Module luminous flux 1800 lm
Luminaire luminous flux 965 lm
Luminaire luminous efficiency 73,1 lm / W

Installation

The luminaire must only be operated with the complete protective cover.
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Pick up the luminaire base.
Lead the mains supply cable through the cable entry of the luminaire base.
Fix the luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.
Pick up the luminaire top and connect the two pin
LED plug connector.
IMPORTANT : Make sure that the 2-pole LED plug connector is not placed inside the rectangular LED recess before you join the luminaire base with the luminaire top.
Guide the mounting sockets of the luminaire top exactly onto the installation bolts of the luminaire base.
Applying even pressure on both sides, lock together the luminaire top and luminaire base

Cleaning Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system from the power supply $BEGA-51295-5K3-Wall-and-Ceiling-Light-FIG- $3$$
Carefully insert a slotted screwdriver successively into the two flat openings at the edge of the luminaire top and lift the luminaire top on both sides away from the luminaire base against the resistance of the locking mechanism.
Disconnect the two-pin LED plug connector.
Please note: To prevent damages or scratches on the surface, set the luminaire top down with the front side on a soft base.
Using a slotted screwdriver, exert pressure on the snap-in hook on the inside of the luminaire top until the LED module releases from the holder.
Remove the LED module. Install the replacement module over the snap-in holder in the luminaire top.
Please follow the installation instructions for the new LED module.
A defective luminaire cover must be replaced.
Pick up the luminaire top and reconnect the two-pin LED plug connector.
Guide the mounting sockets of the luminaire top exactly onto the installation bolts of the luminaire base.
Applying even pressure on both sides, lock together the luminaire top and luminaire base