BEGA 23 250.2 Wall Luminaire Instruction Manual

Table of Contents

Specifications:
- Lamp Module connected wattage: 7.6 W
- Luminaire connected wattage: 8.8 W
- Rated temperature: 25 – 40°C
- Ambient temperature: 25 – 40°C

Safety
- The installation and operation of this luminaire are subject to national safety regulations.
- Installation and commissioning should only be carried out by a qualified electrician. The manufacturer does not accept liability for damage caused by improper use or installation.
Overvoltage Protection
- The electronic components in the luminaire are protected against overvoltage according to DIN EN 61547.
- For additional protection against transients, separate overvoltage protection components are recommended.
- These can be found on the manufacturer’s website.
Installation
- When mounting or dismantling, maintain a minimum distance of 250 mm between the removable cap and the wall. Avoid touching the light output opening of the LED directly during installation or relamping.

Q: What should I do if I need spare parts?
- A: Spare parts for this product include spare glass, LED power supply unit, LED modules in 3000 K and 4000 K, and a gasket. The specific part numbers are 11 002 946 .1R, G DEV-0304/350, LED-0424/930, LED-0424/940, and 83 001 179.
Q: What are the different module designations available for this luminaire?
- A: The available module designations are 23 250.2 K3 and 23 250.2 K4. The details for each are as follows:
- 23 250.2 K3: Module designation – 2x LED-0424/930, Colour temperature – 3000 K, Colour rendering index – CRI > 90, Module luminous flux – 1260 lm, Luminaire luminous flux – 912 lm, Luminaire luminous efficiency – 103.6 lm/W
- 23 250.2 K4: Module designation – 2x LED-0424/940, Colour temperature – 4000 K, Colour rendering index – CRI > 90, Module luminous flux – 1330 lm, Luminaire luminous flux – 962 lm, Luminaire luminous efficiency – 109.3 lm/W

Wall luminaire for indoor use

$BEGA-23-250-2-Wall-Luminaire-FIG-1 $1$$

Application

Wall luminaire · indoor luminaire made of handblown opal glass and metal housing, for all lighting tasks in interior applications.
They are ideal for places where a soft and uniform lighting distribution is required.
Luminaire with a high protection class.

Product Description

Luminaire made of Aluminium, finish Stainless steel
Hand-blown opal glass
Two elongated mounting holes
Width 6mm · 275mm spacing
Insulating housing with cable entry for mains supply cable up to ø 10,5 mm, max. 3 x 1,5@
Connection terminal 2.5@
Earth conductor connection
BEGA Ultimate Driver®
Complies with flicker requirements by IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V x 0/50-60 Hz
DC 176-264 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 44
Protected against granular foreign bodies ≥ 1 mm and splash water Impact strength IK02
Protection against mechanical impacts < 0.2 joule
– Safety mark
– Conformity mark
Weight: 1.5 kg
This product contains light sources of energy
efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

23 250.2K3

23 250.2K4

Insulation housing

For mounting and dismantling please keep a minimum distance of 250 mm between the removable cap and the wall.
LEDs are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.

Open luminaire:

Loosen the knob, and remove the cap and glass.
Drill mounting holes into the mounting surface – spacing 275 mm.
For the mains supply connecting open the insulation housing – pull open – strip mains supply cable max. 15 mm and lead it into the insulation housing – see sketch.
Make earth conductor connection and electrical connection.
Connect both parts of the insulation housing until they audibly engage.
The outer coating of the cable has to be fully enclosed by the compression nipple.
Fix the luminaire with enclosed or any other suitable fixing material onto the mounting surface.
Place glass into the luminaire housing, close the luminaire with the cap, and screw in the knob into the cap.

Replacement of the LED module

The designation of the LED module is noted on a label in the luminaire.
The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system.
Loosen the lateral knob, remove the cap, and take out the glass.
Please follow the installation instructions for the LED module.
The defective glass must be replaced.
Insert glass into luminaire housing, close
luminaire with the cap and screw in the knob into the cap.

Spares