BEGA 50068.3K3 Wall Light for Indoor Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 50068.3K3 Wall Light for Indoor
Instructions for use
Product Description
Installation
Cleaning · Maintenance
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50068.3K3 Wall Light for Indoor

Instructions for use

$BEGA -500683K3-Wall-Light-for-Indoor-fig- $1$$

Application
Free radiating wall luminaire · indoor luminaire with hand-blown three-ply opal glass for a soft and uniform light distribution. The elongated design of this wall luminaire particularly provides suitability for installation on pillars, columns, and the front surface of walls, as well as for recesses or profiles. The luminaire may be installed horizontally or vertically

Product Description

Metal luminaire housing, finish Chrome
Hand-blown opal glass
The electrical equipment can be hinged
2 mounting holes ø 6mm
Distance apart 300mm
Jointing sleeve with cable entry for mains supply cable up to
ø 14 mm, max. 5 x 1.5
Connecting terminals 2.5
Earth conductor terminal
Complies with flicker requirements by IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V x /50-60 Hz
DC 176-276 V
During DC operation the LED power is reduced to 15%
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control
Temporary thermal regulation to protect temperature-sensitive components without
switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK03
Protection against mechanical
impacts < 0.35 joule
r – Safety mark
c – Conformity mark
Weight: 3.0 kg
This product contains light sources of energy efficiency class(es) D

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547. To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Installation

LEDs are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the hexagon socket (wrench size 5) in the locking cap and remove it.
The opal glass can now be hinged together with the electrical equipment to the front.
Remove the opal glass.
Note the position of application of the luminaire »arrow down«.
Drill mounting holes into the mounting surface – spacing 300mm and turn in enclosed or suitable fixing screws.
For the electrical connection undo the screw connection at the line connector and remove the terminal block.
Make earth conductor connection and electrical connection.
Make a connection between the phase with the L marked, the neutral wire at the N marked and the earth conductor at the PE marked connecting terminal.
For digital actuation please use the two connecting terminals DA. If these terminals are not assigned, the luminaire will work with full light output.
Bolt together both screw cable glands firmly.
Hook the luminaire into the fixing screws and tighten.
Slide opal glass over the lamp and fasten it with the locking cap.
Make sure that the gaskets are positioned correctly

Lamp

Module connected wattage 19.2 W
Luminaire connected wattage 22.5 W
Rated temperature ta=25 °C
Ambient temperature ta max=45 °C

50 068.3K3

Module designation
2x LED-0626/930 + 2x LED-0627/930
Color temperature 3000 K
Color rendering index CRI >90
Module luminous flux 3210 lm
Luminaire luminous flux 2286 lm
Luminaire luminous efficiency 101,6 lm/W

50 068.3K4

Module designation
2x LED-0626/940 + 2x LED-0627/940
Color temperature 4000 K
Color rendering index CRI >90
Module luminous flux 3350 lm
Luminaire luminous flux 2386 lm
Luminaire luminous efficiency 106 lm/W

Cleaning · Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt.
The defective glass must be replaced.

Replacement of the LED module

The designation of the LED module is noted on a label in the luminaire.
The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by a qualified person using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the
LED module.
The defective glass must be replaced.
Close the luminaire.

Spares