BEGA 23 250.1 Wall Luminaire For Indoor Use Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 23 250.1 Wall Luminaire For Indoor
Instructions for use
Product Description
Installation
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 23 250.1 Wall Luminaire For Indoor

Instructions for use

$BEGA-23-250-1-Wall-Luminaire-For-Indoor-Use-fig- $1$$

Application
Wall luminaire · indoor luminaire made of handblown opal glass and metal housing, for all lighting tasks in interior applications. They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with a high protection class.

Product Description

Luminaire made of Aluminium, finish color white
Hand-blown opal glass
Two elongated mounting holes
Width 6mm · 275mm spacing
Insulating housing with cable entry for mains supply cable up to ø 10,5 mm, max. 3 x 1,5
Connection terminal 2.5
Earth conductor connection
BEGA Ultimate Driver
Complies with flicker requirements by IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V x /50-60 Hz DC 176-264 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 44
Protected against granular foreign bodies
≥ 1 mm and splash water
Impact strength IK02
Protection against mechanical
impacts < 0.2 joule
– Safety mark
c – Conformity mark
Weight: 1.7 kg
This product contains light sources of energy efficiency class(es) D

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547. To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Module connected wattage 7.6 W
Luminaire connected wattage 8.8 W
Rated temperature ta=25 °C
Ambient temperature ta max=40 °C

23 250.1K3

Module designation 2x LED-0424/930
Color temperature 3000 K
Color rendering index CRI >90
Module luminous flux 1260 lm
Luminaire luminous flux 912 lm
Luminaire luminous efficiency 103,6 lm/W

23 250.1K4

Module designation 2x LED-0424/940
Color temperature 4000 K
Color rendering index CRI >90
Module luminous flux 1330 lm
Luminaire luminous flux 962 lm
Luminaire luminous efficiency 109,3 lm/W

Installation

For mounting and dismantling please keep a minimum distance of 250 mm between the removable cap and the wall. LEDs are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Open luminaire
Loosen the knob, and remove the cap and glass. Drill mounting holes into the mounting surface – spacing 275 mm. For the mains supply connecting open the insulation housing – pull open – strip mains supply cable max. 15 mm and lead it into the insulation housing – see sketch. Make earth conductor connection and electrical connection. Connect both parts of the insulation housing until they audibly engage. The outer coating of the cable has to be fully enclosed by the compression nipple. Fix the luminaire with enclosed or any other suitable fixing material onto the mounting surface. Place glass into luminaire housing, close-luminaire with the cap and screw in the knob into the cap.

Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire. The light color and light output of BEG replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system. Loosen the lateral knob, remove the cap, and take out the glass. Please follow the installation instructions for the LED module. The defective glass must be replaced. Insert glass into luminaire housing, close the luminaire with the cap, and screw in the knob into the cap.

Spares