BEGA 22228 Wall Luminaire Applique Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
BEGA 22228 Wall Luminaire Applique
Instructions for use
Application
Wall luminaire for orientating lighting tasks. The color temperature of the
luminaire can be set optionally to 3000K and 4000K.
Product Description
- Luminaire made of aluminum alloy, aluminum, and stainless steel
- BEGA Unidure® coating technology
- Color graphite or silver
- Matt safety glass with optical structure
- Silicone gasket
- Reflector made of pure anodized aluminum
- 2 mounting holes ø 4.4mm
- Distance apart 90mm
- 1 cable entry for the mains supply cable up to ø 10,5mm
- Connection terminal 2.5
- Earth conductor connection
- BEGA Ultimate Driver
- Complies with flicker requirements by IEEE 1789,
- DIN IEC/TR 63158, DIN IEC/TR 61547-1
- LED power supply unit 220-240 V x 0/50-60 Hz
- DC 176-264 V
- BEGA Thermal Switch
- Temporary thermal shutdown to protect temperature-sensitive components
- Safety class I
- Protection class IP 65
- Dust-tight and protection against water jets
- Impact strength IK08
- Protection against mechanical
- impacts < 5 joule
- – Safety mark
- c – Conformity mark
- Weight: 0.65 kg
- This product contains light sources of energy efficiency class(es) C
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage by DIN EN 61547. To achieve additional protection against e.g.
transients, etc. we recommend separate overvoltage protection components. You
can find them on our website at
www.bega.com. The ideal protection of all electronic
components installed in the luminaires is achieved by using bounce-free
switching contacts such as an electronic relay (solid-state relay), e.g. BEGA
71320.
Installation
LEDs are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Undo the hexagon socket head screws and lift the luminaire top. For fixing the luminaire onto the mounting surface the complete electrical equipment must be removed from the luminaire base. Lead the main supply cable through the cable entry of the luminaire base. Fix the luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Be sure to use the gasket rings supplied. Make the earth conductor connection and the electrical connection. Reassemble the LED unit and tighten the fixing screws firmly and evenly. Please observe that the LED board is not damaged mechanically.
The color temperature of the LED module was set to 3000 K by default (switch position 1: “off”, 2: “on”). For color temperature 4000 K, the switch position 1: “on” and 2: “off must be selected. Switching may only be carried out when disconnected from the power supply! To guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire. Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire. Connect the green and yellow protective earth conductor from the luminaire top to the terminal marked 1 in the mounting plate. Make sure that the gasket is positioned correctly. Install luminaire top and tighten. In doing so please note that the cables of the electrical equipment will not be pinched by the luminaire top. Tighten the screws evenly.
Lamp
- Module connected wattage 2.9 W
- Luminaire connected wattage 3.8 W
- Module designation LED-1466/83040
- Color rendering index CRI >80
- Rated temperature ta=25 °C
- Ambient temperature ta max=50 °C
- Operation at colour temperature 3000 K
- Module luminous flux 540 lm
- Luminaire luminous flux 188 lm
- Luminaire luminous efficiency 49,5 lm/W
- Operation at colour temperature 4000 K
- Module luminous flux 580 lm
- Luminaire luminous flux 202 lm
- Luminaire luminous efficiency 53,2 lm/W
Cleaning Maintenance
- Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
- Do not use high-pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire. The
light color and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The module can be replaced by qualified
persons using standard tools. Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module. Inspect and,
if necessary, replace the luminaire gaskets. The defective glass must be
replaced. Close the luminaire.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>