BEGA 33534 Ceiling And Wall Luminaire Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 33534 Ceiling And Wall Luminaire
DIMENSION
Instructions for use
Overvoltage protection
Installation
Cleaning Maintenance
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 33534 Ceiling And Wall Luminaire

BEGA-33534-Ceiling-And-Wall-Luminaire-PRODUCT

DIMENSION

Ceiling and wall luminaire

$BEGA-33534-Ceiling-And-Wall-Luminaire-FIG-1 $1$$

Instructions for use

Application

Ceiling and wall luminaire with high protection class for a variety of lighting tasks.
A luminaire made of aluminium alloy and crystal glass.
The colour temperature of the luminaire can be set optionally to 3000K and 4000K.

Product Description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Crystal glass with a white matt finish
Silicone gasket2 mounting holes ø 4.5mm
Distance apart 110mm 2 cable entries for through-wiring of mains supply cable ø 7-10.5mm
Connecting terminal 2.5@ with plug connection
Earth conductor connection
BEGA Ultimate Driver®
Complies with flicker requirements per IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V x 0/50-60 Hz
DC 176-264 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK07
Protection against mechanical impacts < 2 joule
– Safety mark
– Conformity mark
Weight: 1.0 kg
This product contains light sources of energy efficiency class(es) B

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71320.

Lamp

Module connected wattage 2.8 W
Luminaire connected wattage 3.9 W
Module designation LED-1512/83040
Colour rendering index CRI >80
Rated temperature ta=25 °C
Ambient temperature ta max=50 °C
Operation at colour temperature 3000 K
Module luminous flux 580 lm
Luminaire luminous flux 355 lm
Luminaire luminous efficiency 91 lm/W
Operation at colour temperature 4000 K
Module luminous flux 595 lm
Luminaire luminous flux 364 lm
Luminaire luminous efficiency 93,3 lm/W

Installation

LEDs are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the locking screw and turn the cover ring as far as it will go.
Remove the cover ring and glass from the luminaire base.
Disassemble the LED module.
Disconnect the plug-connection of the LED connecting cable.
Lead the main supply cable through the cable entry into the luminaire back housing.
Fix the luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.

The colour temperature of the LED module was set to 3000 K by default (switch position 1: “on”, 2: “off”). For colour temperature 4000 K, the switch positions 1: “off” and 2: “on” must be selected.

Switching may only be carried out when disconnected from the power supply!

To guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
Connect the LED connection cable utilizing a plug connector.
Assemble LED module.
Tighten the screws evenly. Please observe that the LED board is not damaged mechanically.
Make sure that the gasket is positioned correctly.
Place the cover ring with glass onto the luminaire base and turn it clockwise as far as it will go. Tighten the locking screw.

Cleaning Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced.
Close the luminaire.

Spares