BEGA 85 182 Garden and Pathway Luminaire Instruction Manual

Table of Contents

Specifications:
- Application: Garden and path luminaire
- Lighting: Shielded, flat beam light directed downwards
- Lamp Module connected wattage: 4.8 W
- Luminaire connected wattage: 5.6 W
- Colour temperature: 3000 K
- Colour rendering index (CRI): > 80
- Module luminous flux: 940 lm
- Luminaire luminous flux: 350 lm
- Luminaire luminous efficiency: 62.5 lm / W
- Recommended light point interval: 4 m

Lighting Technology:
- The light from this luminaire is directed evenly and efficiently onto the surface to be illuminated. Less than 1% of the luminaire luminous flux is emitted into the upper halfspace of the luminaire.
Safety:
- The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should carry out installation and commissioning to avoid damage due to improper use or installation. The manufacturer does not accept liability for damages resulting from improper handling.
Overvoltage Protection:
- The electronic components in the luminaire are protected against overvoltage as per DIN EN 61547. Additional protection against transients is recommended through separate overvoltage protection components available on the manufacturer’s website.
Ideal Protection:
- To ensure optimal protection of all electronic components, use bounce-free switching contacts like an electronic relay (solid-state relay).

Q: Can I replace specific parts of the luminaire?
- A: Yes, you can replace parts such as the LED power supply unit, LED module 3000 K, gasket, and cover with the corresponding spare parts available.

Garden and pathway luminaire

$BEGA-85-182-Garden-and-Pathway-Luminaire-FIG-1 $1$$

Application

Garden and path luminaire with shielded, flat beam light directed downwards for illuminating entrances, footpaths as well as many areas of garden and landscape architecture.
The light point is integrated as a cut-out in the bollard tube of the luminaires.

Product Description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Matt safety glass
Reflection surface graphite
Luminaire with anchorage unit for fixing in the soil
The anchorage unit is made of galvanised steel according to EN ISO 1461
Connection set with gasket inserts and drip-proof cap for through-wiring power connecting cables of ø 10–13.5mm, max. 3 G 2.5@
BEGA Ultimate Driver®
Complies with flicker requirements following IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-280 V
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
– Conformity mark
Weight: 3.9 kg
This product contains light sources of energy efficiency class(es) C

Lamp

85 182K3

Lighting technology

Dark Sky

The light from this luminaire is directed evenly and highly efficiently onto the surface to be illuminated.
Less than 1% of the luminaire luminous flux is emitted into the upper halfspace of the luminaire.

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71320.

The base of the luminaire must not be lower than the upper edge of the floor covering.
A cable length of 0,3m above the mounting surface is required for the electrical connection.
Remove the hexagon socket screws (wrench size 3) at the base of the luminaire and remove the anchorage unit.
Pass the underground cable into the anchorage unit from underneath.
When installing the anchorage unit, make sure that the tube is vertical and 100–120 mm above the upper edge of the floor covering.
The luminaire is connected using the supplied connection set. Complete the installation according to the installation instructions shown. Place the luminaire on the anchorage unit via the drip-proof cap and secure in place.

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced. Close the luminaire.

Spares