BEGA 24605 Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 24605 Wall Luminaire
Product Information
Product Usage Instructions
Application
Product Description
DIMENSION
Overvoltage protection
Safety
Installation
Cleaning Maintenance
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24605 Wall Luminaire

Product Information

Product Name: Wandleuchte Wall luminaire Applique
Model Number: 1230
IP Rating: IP65
Power Supply: 110V
Weight: 105g
Dimensions: 1150mm

Overvoltage Protection: The luminaire is protected against overvoltage according to DIN EN 61547. Additional overvoltage protection components are recommended for extra protection against transients and can be found on the manufacturer’s website.
Safety: The installation and operation of this luminaire should be done in accordance with national safety regulations. Only qualified electricians should perform theinstallation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. Any modifications to the luminaire should be done by a qualified person who will be considered the manufacturer.

Product Usage Instructions

Installation:
Undo the hexagon socket head screws (wrench size 3 mm) and lift the mounting bar out of the luminaire housing.
Note the position of application of the mounting bar on the wall side.
Lead the mains supply cable through the opening of the mounting bar.
Fix the mounting bar onto the mounting surface using the enclosed or other suitable fixing material. Make sure to have an even mounting surface.
Do not remove the desiccant bag from the luminaire housing as it is necessary to remove residual moisture.
Replacing the LED module / Power supply unit:
The LED module designation is noted on a label inside the luminaire.
Qualified persons can replace the module using standard tools.
Avoid touching the light output opening of the LED directly during relamping.

Application

Wall luminaire with light emission on two sides and symmetrical light distribution to illuminate façade and wall surfaces.
A luminaire that allows interesting illumination concepts individually, in rows or groups.
The luminaire can be installed in any burning position

Product Description

Luminaire made of aluminum and stainless steel
BEGA Unidure® coating technology
Safety glass with optical structure
Reflector made of pure anodized aluminium
Mounting bar with 2 elongated holes 7 mm width, 1150 mm spacing
Connection box with 2 cable entries for through-wiring of the mains supply cable
ø 5-13 mm, max. 5×2,5@
Connecting terminals and earth conductor terminal 2,5@
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-280 V
During DC operation the LED power is reduced to 15 %
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK06
Protection against mechanical impacts < 1 joule
Safety mark
Conformity mark
Weight: 11.2 kg

This product contains light sources of energy efficiency class(es) C

DIMENSION

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Installation

Undo hexagon socket head screws (wrench size 3 mm) and lift the mounting bar out of the luminaire housing. Note the position of application of the mounting bar – wall side.
Lead mains supply cable through the opening of the mounting bar.
Fix the mounting bar with enclosed or other suitable fixing material onto the mounting surface.
It is absolutely essential to have an even mounting surface.
$BEGA-24605-Wall-Luminaire-FIG- $4$$
Use the supplied connection box to make the electrical connection (see illustration).
Undo the hexagon socket head screws (wrench size 3 mm) and open the connection box.
Run the power connecting cable through the
M20 cable gland and into the connection box.
For through-wiring, the factory-fitted dummy plugs must be removed.
Tighten the cable glands securely.
Make the earth conductor connection and the electrical connection.
Observe the correct configuration of the connecting cable. Connect the earth conductor to the green-yellow wire (PE), the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
The control cables are connected via the two DALI-labelled wires.
If these wires are not assigned, the luminaire will work with full light output.
Close the connection box. Make sure the gasket is properly located.
Hang the luminaire housing in the mounting rail and screw it in place.

Please note:

Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Replacing the LED module/Power supply unit

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
$BEGA-24605-Wall-Luminaire-FIG- $5$$
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during relamping.
Unscrew the two hexagon socket screws (wrench size 3 mm) through the openings in the luminaire housing and remove the luminaires from the mounting rails.
To open the connection box, unscrew the hexagon socket screws (wrench size 3 mm) and disconnect the electrical connection of the power connecting cable.
To replace the LED module or power supply unit, remove the front housing cover (on the side of the cable entry).
Loosen the hexagon socket screw (wrench size 3 mm) at the back of the luminaire housing and remove the front housing cover.
Remove the earth conductor connection plug. To pull the module carrier out of the housing, unscrew the hexagon socket screw (wrench size 5 mm) and remove the terminal block. Carefully pull the reflector out of the housing. Pull out the module carrier until the connection terminals are exposed.
Remove the connecting cable from the PSU terminals and pull out the module carrier entirely.
Replace the PSU / LED module. Follow the installation instructions for the LED module. Install in reverse order.
Push the reflector with anodised finish into the luminaire housing directed outwards.
Make sure that the module carrier and housing are positioned correctly (see drawing Item A).