FORTIN 68461 2021 Honda CR V Remote Starters Regular Key And Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
REV.: 20220105
Guide # 68461
REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
68461 2021 Honda CR V Remote Starters Regular Key And Alarm Systems
VEHICLE
YEARS
Vehicle functions supported in this diagram (functional if equipped) |
- Immobilizer bypass
- T-Harness available**
- Harnais en T disponible**
- Lock
- Unlock
- Arm
- Disarm
- Trunk (open)
- Tachometer
- Parking Lights
- Door Status
- Trunk Status
- Hood Status*
- Hand-Brake Status
- Foot-Brake Status
- OEM Remote Monitoring
FIRMWARE VERSION
73.[38]
HONDA/ACURA MINIMUM
To add the firmware version and the options, use the FLASH LINK
UPDATER or FLASH LINK MOBILE tool, sold separately.
| Program bypass option
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
---|---
| Program bypass option:
| Program bypass option
(If equiped with OEM alarm):
| Program bypass option
(Vehicle hybrid only):
UNIT OPTION| DESCRIPTION
---|---
A11
OFF/NON| Hood trigger (Output Status).
C1| OEM Remote status (Lock/Unlock) monitoring
D2| Unlock before / Lock after (Disarm OEM alarm)
D4| Hybrid mode (Vehicle hybrid only)
NOTES
** Sold separately
MANDATORY INSTALL
- HOOD PIN
HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
A11
OFF/NON
Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
This guide may change without notice. See www.fortin.ca for latest version.
DESCRIPTION
This guide may change without notice. See www.fortin.ca for latest version.
AUTOMATIC TRANSMISSION WIRING CONNECTION
DCRYPTOR PROGRAMMING PROCEDURE
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.
Press and hold the
programming button: Connect the 4-PIN Data-link harness (Black connector).
→ The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
Release the programming button when the Blue & Red LEDs are ON.
If the Blue & Red LEDs are not ON solid disconnect the 4-PIN Data-Link and go
back to step 1.
Connect the required remaining harnesses.
Press and release the programming button three times (3x).
→ The Red and Blue LEDs will alternate between 2 flashes and a pause.
Turn the key to the Ignition ON/RUN position.
→ Wait for the Yellow Led to flash rapidly.
→ Wait for the Blue LED to flash rapidly.
Turn the
key to the OFF position.
→ The Red and Yellow LEDs will start flashing alternatively.
KEY BYPASS PROGRAMMING PROCEDURE 2/2
Disconnect all the connectors and after the Data-Link (4-pins) connector.
Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DC ryptor menu.
*Parts required (not included)
AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and
after, all the remaining connector.
The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION
PROCEDURE
Test the remote starter. Remote start the vehicle.
REMOTE STARTER FUNCTIONALITY
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest firmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit
before connecting to it. Only a computer safe logic probe or digital
multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no
liability or responsibility whatsoever pertaining to the accuracy or currency
of the information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualified technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>