PIT PSW1100-W Drainage Pump User Manual

PIT PSW1100-W Drainage Pump

Safety instructions

General Power Tool Safety Warnings

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

ATTENTION!

• Do not use the product without protec-tive grounding!
• Installation of a residual current device (RCD) with a rated leakage current of 30 mA is mandatory!
• The installation of the product and the electrical outlet for connecting it to the mains must be carried out by qualifi ed electricians.
• To avoid accidents, it is strictly forbidden to carry out any repair / mainte-nance work on the equipment without disconnecting it from the electrical network.
• The product is intended for pumping ONLY fresh water. DO NOT use the pump for pumping salt water, solvents, corrosive, flammable or explosive liquids, liquid food, or feces.
• Do not allow the pump to run dry (without water intake) and/or with a blocked supply channel.
• Do not block the water intake holes of the product.
• To avoid product damage, DO NOT turn ON or USE the product at temperatures below 1 ° C, and do not leave it working overnight if frost is possible.
• The pump is cooled by the surrounding water. Therefore, do not operate the product outside of water and do not use in bodies of water or tanks with water temperatures above 35 ° C.
• Do not repair or disassemble the product yourself.

Electrical safety

ATTENTION!
If the safety instructions are not followed, there is a risk of electric shock.

• The product is intended for use in FULL immersion. Monitor the condition of the mains cable insulation, do not damage the insulation. When connecting the product to the mains, use only grounded sockets – this will help to avoid electric shock.
• Unsuitable extension cords can be hazardous. Outdoors, use only approved and appropriately marked extension cords with suffi cient wire cross-section.
• Do not use the mains power cable to transport or fi x the instrument.
• When disconnecting the appliance from the mains, pull the plug, not the cable.
• Be careful not to pinch the power cord or rub it against sharp edges.
• Install the device in a rack and over-fi ll-proof position.
• The mains voltage must correspond to the voltage specified in the technical specifi cations.
• DO NOT operate the pump in water bodies (ponds, pools), in which there are or may be people, and it is also forbidden for people to be in a water body with the pump running.
• Electrical connections must only be made by a qualifi ed electrician.

Safety of people

• For safety reasons, persons under the age of 16 or those who have not read this manual must not be allowed to work with the device.
• The pump is not intended for use by persons with reduced physical or mental capabilities or lack of experience and knowledge of the user unless he is supervised and instructed in the use of the device by a person responsible for safety.
• It is forbidden to operate and service the pump while in a state of extreme fatigue, alcohol, drug intoxication or under the influence of strong medications.
• Keep children and pets away from the pump while it is running. Children should be supervised to ensure that they do not play with the device.

Safety instructions for working with the pump

• Any use of the pump in violation of the rules of ego operation is considered as used for other purposes. Damage resulting from use for other purposes is solely the responsibility of the user.
• The pump is not intended for profes-sional or industrial use. Long-term continuous use is not allowed.
• Unauthorized modifi cation of the pump is prohibited.
• It is forbidden to pump explosive, flammable, corrosive or health-hazardous substances, as well as water containing mechanical impurities in the form of sand, stones, etc.
• The pump is not suitable for pumping chlorine-containing water in swimming pools.
• Not recommended for pumping drink-ing water.
• When starting the pump for the first time, ensure that it is completely fi lled with water. it is not allowed to operate the pump without water consumption.
• To avoid freezing, completely drain the pump and pressure line.
• Do not exceed the maximum immersion depth for the pump – an increased load (increased pressure of the water column) if it is impossible to pump water through the pump (due to the pressure, more than the maximum) can lead to overheating and damage to the impeller.

Product Description and Specificationcations

Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric shock, fire, and/or serious injury. Please observe the illustrations at the beginning of this operating manual.

Intended use

A submersible drainage pump is designed for pumping water in garden plots when draining tanks and reservoirs, maintaining a given water level in a reservoir and a reservoir, organizing water intake from a depth (wells, wells), and supplying it to a height, using it in aeration and drainage systems for a limited period of time … The pump can be used in polluted water. The product is not intended for continuous operation (continuous pumping mode).

Product Features

The numbering of the product features refers to the diagram of the power tool on the graphics.

1. Pump
2. Herringbone fitting
3. Switch cable
4. Adjustment slot
5. Float switch

Technical Data

Contents of delivery

• Submersible drainage pump 1 pc
• The float switch 1 pc
• Outlet nipple 1 pc
• Instruction manual 1 pc

Note
Text and numbers may contain technical errors and typographical errors. Since the product is constantly being improved, P.I.T. reserves the right to make changes to the specifications and product specifi cations specifi ed here without prior no-tice.

Preparation for work

When installing the water inlet, keep in mind that:

• The pump performance directly depends on the pressure (water rise). It is not recommended to use the pump at the maximum head in this case, as the water supply will be minimal.
• The hydraulic resistance of 10 meters of the horizontal section of the line equals approximately 1 meter of the head.

Installation

• Check the power cable for damage, if found, contact an authorized service center for replacement. Make sure that the parameters of the power supply network correspond to those indicated in the table, otherwise, the pump will not be able to perform its functions in full or may fail.
• Make sure the outlet line or hose is clear, not clogged or pinched before use. Check and if necessary clean the water intake of the pump.
• Connect a hose to the water inlet. Fasten it securely with a hose clamp. Please note that the pump performance depends on the hose diameter, the smaller the diameter of the connected hose, the lower the pump performance. The minimum permissible diameter of the connection hose is 25 mm.
• Adjust the length of the float switch wire by attaching the wire to the hole in the pump body. This allows you to adjust the immersion depth and the automatic cut-off depth. If the water level falls below the level of the fl oat switch, the pump will shut off. This protects the pump from running dry. The fl oat switch can be forcibly locked in order to pump liquid to the level of the water intake holes. Fasten the fl oat switch vertically in the slots on the pump housing. Make sure that the intake holes are always covered with water. Otherwise, if the water runs out and the pump runs dry, the pump parts will wear out quickly and the pump may fail.

Place the pump on a solid, clean (no sediment) base or, if depth permits, hang it from the carry handle using a rope or cable (sold separately). Do not suspend the pump by the power cable. The free space around the pump should be at least 50×50 cm. When the pump is fi rst immersed in water, tilt it, so you remove air from the water intake part. Otherwise, the initial start-up of the pump will be diffi cult due to the airlock. Connect the pump to the power supply. In automatic mode, the pump will turn on and off when the fl oat switch reaches certain positions. If you need to finish work, disconnect the power plug from the mains.

Exploitation
The submersible drainage pump is designed for operation underwater at a depth of 5 meters at temperatures from + 1 ° C to + 35 ° C in a place with a low level of pollution.

ATTENTION!
Every 15 minutes of continuous operation of the pump, it is necessary to take a break for 10-15 minutes.

• Make sure that the network parameters correspond to the parameters indicated on the pumping equipment and in this operat-ing manual.
• Make sure that the pumping equipment will be connected to the mains via a residual current device with a rated tripping current of ≤ 30 mA.

Auto mode

In automatic mode, a fl oat switch controls the operation of the pump.
In order for the pump to start working in automatic mode, lower it into the water, and connect the mains cable plug to the mains. The pump will run until the fl oat switch reaches the minimum depth required to shut off. It is recommended to install the pump on a solid base to maintain an upright position. After diving, make sure that the fl oat switch is not obstructed.

ATTENTION!
The pump must be lowered to a depth using a cable tied to the handle. Never immerse the pump in water using the main cable.

Manual mode
For manual operation, the motor can be started by lifting the float switch by hand. Lower the fl oat switch to turn off the pump.

ATTENTION!
During manual operation, do not leave the pump unattended; working without water will damage it.

End of work
After use, run clean water through the pump for 2-3 minutes in order to get rid of sediment and particles that may accumulate in the pump or outlet hose. Disconnect the main cable from the mains, remove the pump from the water and move it to a dry ventilated area.

Note!
The pump does not have an automatic shutdown system in the absence of water fl ow through it. Therefore, ALWAYS turn on the tap first, then turn on the product. It is not allowed to operate the pump with a closed water supply pipeline and “dry” (without water intake). To turn off the pump at the end of work, unplug the power plug.

ATTENTION!
If the water level is too low, when the pump is turned off, any impurities inside the pump will dry out quickly. This can result in the pump not starting when the water level rises. To ensure efficient pump operation, regularly clean the bottom of the shaft to remove any debris.

Note!
To prevent water from draining from the pipeline when the pump is turned off, we recommend installing a non-return valve (not included in the delivery set). Before long-term storage, as well as when cleaning for the winter, disconnect the hoses from the product and completely drain the wa-ter from the hoses and the product.

Maintenance and Cleaning

• All maintenance work must be carried out with the cable disconnected from the mains.

If the pump is not used for a long time, it must be disconnected from the mains. The pump does not need any special main-tenance. Periodically it is necessary to check the water intake part, if it becomes dirty, clean it. Regularly clean the body of the product from accumulated dirt.

All other types of maintenance and repairs should be carried out only by specialists of service centers.

Service

• Have your power tool repaired only by qualifi ed personnel and only with original replacement parts. This ensures the safety of the power tool.

The list of authorized service centers can be viewed on the official website of P.I.T. by the link: https://pittools.ru/servises/.

Storage and transportation

Storage:
Store clean, in a dry ventilated area, away from heat sources. Products can be transported by any type of closed transport in the manufacturer’s packaging or without it, while preserving the product from mechanical damage, and atmospheric precipitation.

Dispose of waste

Damaged power tools, batteries, accessories, and waste packaging materials must be recycled and reused in an environmentally friendly manner. Do not throw power tools and accumulators/batteries into general household waste!

Product serial number interpretation

The first and second digits of the product serial number from left to right Year of production, the third and fourth digits indicate the month of production, the fi fth and sixth digits indicate the production day.

TERMS OF WARRANTY SERVICE

1. This Warranty Certifi cate is the only document that confirms your right to free warranty service. Without presenting this certifi cate, no claims are accepted. In case of loss or damage, the warranty certifi cate is not restored.

2. The warranty period for the electric machine is 12 months from the date of sale, during the warranty period the service department eliminates manufacturing defects and replaces parts that have failed due to the fault of the manufacturer free of charge. In the warranty repair, an equivalent operable product is not provided. Replaceable parts become the property of service providers. P.I.T. is not liable for any damage that may be caused by the operation of the electric machine.

3. Only clean tools accompanied with the following duly executed documents: this War-ranty Certifi cate, Warranty Card, with all fields, filled out, bearing the stamp of the trade organization and the signature of the buyer, shall be accepted for warranty repair.

4. Warranty repair is not performed in the following cases:

   • damage to the pumping part or its parts as a result of the pump running dry (without water) or during prolonged operation with a closed pressure pipeline.
   • in the absence of a Warranty Certifi cate and a Warranty Card or their incorrect execution;
   • with failure of both a rotor and a stator of the electric engine, charring or melting of the primary winding of the welding machine transformer, charging or starting-charging device, with internal parts melting, burn down of electronic circuit boards;
   • if a Warranty Certificate or a Warranty Card does not correspond to this electric machine or to the form established by the supplier;
   • upon expiration of the warranty period;
   • at attempts of opening or repair of the electric machine outside the warranty workshop; making constructive changes and lubrication of the tool during the warranty period, as evidenced, for example, by the creases on the spline parts of the fasteners of non-rotational parts.
   • when using electric tools for production or other purposes connected with making a profit, as well as in case of malfunctions related to instability of the power network parameters exceeding the norms established by GOST;
   • in the events of improper operation (use the electric machine for other than intended purposes, attachments to the electric machine of attachments, accessories, etc. not provided by the manufacturer);
   • with mechanical damage to the case, and power cord, and in case of damages caused by aggressive agents and high and low temperatures, ingress of foreign objects in the ventilation grids of the electric machine, as well as in case of damage resulting from improper storage (corrosion of metal parts);
   • natural wear and tear on the parts of the electric machine, as a result of long-term op-eration (determined on the basis of the signs of full or partial depletion of the specified mean life, great contamination, presence of rust outside and inside the electric machine, waste lubricant in the gearbox);
   • use of the tool purposes for other than specifi ed in the operating instructions.
   • mechanical damages to the tool;
   • in the event of damages due to non-obser-vance of the operating conditions specifi ed in the instruction (see chapter “Safety Precautions” of the Manual).
   • damage to the product due to non-obser-vance of the rules of storage and transportation.
   • in case of strong internal contamination of the tool.
     Preventive maintenance of electric machines (cleaning, washing, lubrication, replacement of anthers, piston, and sealing rings) during the warranty period is a paid service. The service life of the product is 3 years. Shelf life is 2 years. It is not recommended for oper-ation after 2 years of storage from the date of manufacture, which is indicated in the serial number on the label of the instrument, without preliminary verifi cation (for the definition of the date of manufacture, see the User’s Manual earlier).
     The owner is notified of any possible violations of the above terms of warranty service upon completion of diagnostics in the service center. The owner of the tool entrusts the diagnostic procedure to be conducted in the service center in his absence. Do not operate the electric machine when there are signs of excessive heat, sparking, or noise in the gearbox. To determine the cause of the malfunction, the buyer should contact the warranty service center. Malfunctions caused by the late replacement of carbon brushes of the engine are eliminated at the expense of the buyer.

5. The warranty does not cover:

   • replacement accessories (accessories and components), for example, batteries, discs, blades, drill bits, borers, chucks, chains, sprockets, collet clamps, guide rails, tension, and fastening elements, trimming device heads, the base of grinding and belt sander ma-chines, hexagonal heads, etc.,
   • fast-wearing parts, for example, carbon brushes, drive belts, seals, protective covers, guiding rollers, guides, rubber seals, bearings, toothed belts, wheels, shanks, brake belts, starter ratchets and ropes, piston rings, etc. Their replacement during the warranty period is a paid service;
   • power cords, in case of damage to the insulation, power cords are subject to mandatory replacement without the consent of the owner (paid service);
   • tool case.

WARRANTY CERTIFICATE

Dear customer!
Thank you for purchasing the P.I.T tool, and we hope that you will be satisfi ed with your choice. In the process of manufacturing the P.I.T tools pass multilevel quality control, if nevertheless, your product will need maintenance, please contact the authorized P.I.T service centers.

Attention!
When buying, ask a seller to check the completeness and operability of the tool, to fi ll out the Warranty Certifi cate, the Warranty Card (the boxes shall be filled out by a seller), and to affix the seal of the trade organization in the Guarantee Certifi cate and the Warranty Card.

Warranty
By this Warranty Certifi cate, P.I.T. company guarantees the absence of defects of the production nature. In the event any of the above defects are detected during the warranty period, the specialized P.I.T. service centers shall repair the product and replace the defective spare parts free of charge.

The warranty period for P.I.T. electric machines is 12 months from the date of sale. “The warranty maintenance terms are acknowledged and accepted. The operability and completeness of the product are checked in my presence. No claims on quality and appearance.”
Buyer’s Signature___ Surname (legibly) __
Phone __

WARRANTY CARD

№ 1

Name____ Serial Number
Sale Date ____20__
(Filled out by a Seller)

WARRANTY REPAIR CARD
Date of Acceptance for Repair ____20
Application for Repair _
Customer ___
Phone (Address)____
Cause of Application_____
Date of Receipt from Repair ____20
The Tool is checked in my presence__

(The Order shall be performed in a Service Center) (Signature)

№ 2

Name____ Serial Number
Sale Date ____20
(Filled out by a Seller)
WARRANTY REPAIR CARD
Date of Acceptance for Repair ___20_
Application for Repair _
Customer ___
Phone (Address)____
Cause of Application_____
Date of Receipt from Repair ____20
The Tool is checked in my presence__

(The Order shall be performed in a Service Center) (Signature)

№ 3

Name____ Serial Number
Sale Date ____20
(Filled out by a Seller)
WARRANTY REPAIR CARD
Date of Acceptance for Repair ___20_
Application for Repair _
Customer ___
Phone (Address)____
Cause of Application_____
Date of Receipt from Repair ____20
The Tool is checked in my presence__

(The Order shall be performed in a Service Center) (Signature)

www.pit-tools.com

info@pittools.ru

Made in China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>