baby trend ST12E72D Passport Cargo Stroller Instruction Manual
- June 5, 2024
- baby trend
Table of Contents
baby trend ST12E72D Passport Cargo Stroller
WARRANTY
DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT
BABY TREND® FOR REPLACEMENT PARTS, SERVICE AND REPAIR.
The Baby Trend® warranty covers workmanship defects within 1 year of purchase.
Any product which has been subjected to misuse, abuse, abnormal use, excessive
wear and tear, improper assembly, negligence, environmental exposure,
alteration or accident, or has had its serial number altered or removed
invalidates all claims against the manufacturer. Any damage to property during
installation is the sole responsibility of the end user.
Customer Service Department can be contacted at 1
800-328-7363 Monday through Friday
between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required
prior to returning product(s) to Baby Trend®. Please visit
http://babytrend.com/pages/limited-warranty
for complete warranty details.
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
PARTS
Check that you have all the parts for this model before assembling the stroller.
Rear Axle parts (2) caps and spare parts
Rear Axle spare parts (2) caps, (2) pins, (4) washers
WARNING: Please follow all of these instructions to ensure the safety of
your child. Keep these instructions for future reference.
WARNING: Failure to follow these instructions could result in serious
injury or death. Avoid serious injury from falling or sliding out, always use
the safety harness and ensure that the children are properly positioned
according to these instructions.
WARNING: Never leave children unattended.
WARNING: Care must be taken when folding and unfolding the stroller to
prevent finger entrapment
CAUTION: Do not allow children near stroller while folding and unfolding.
WARNING: Wheel can detach and cause tip over. Pull on the wheel to assure
it is securely attached.
WARNING: Care must be taken when folding stroller to prevent damage. Make
sure all accessories, mobile phones, diaper bags or purses are removed before
folding. Failure to remove items in, or on the stroller so may result in
damage to the stroller or the item(s) if not removed. Baby Trend® will not be
liable or warrant any damage.
-
CAUTION: This single stroller is designed for one child only. Use with more than one child may cause the unbalance condition which can injure/ harm your child.
-
Purses, shopping bags, parcels, diaper bags or accessory items may change the balance of the stroller and cause a hazardous, unstable condition.
-
The maximum weight that can be carried in the storage basket is 5 pounds (2.27kg). Excessive weight may cause a hazardous unstable condition to exist.
-
The maximum weight that can be carried in the child tray is 3 pounds (1.36 kg).
-
The maximum weight that can be carried in the parent tray is 3 pounds (1.36 kg).
-
Be certain the stroller is completely opened and locked in place before allowing a child near the stroller.
-
The child occupant must not exceed 50 lb (22.67 kg) or over 42 inches (106.7 cm) tall when used with the maximum weight on the child tray, parent tray and basket. Do not exceed 60 lb
(27.21 kg) including the weight used in the accessories. Use of the stroller and attached car seat with a total weight more than 60 lb (27.21 kg) will cause excessive wear and stress on the stroller and may cause a hazardous unstable condition to exist. -
ALWAYS refer to the manual located under the car seat for car seat weight limitations.
-
NEVER use the stroller on stairways or escalators.
-
NEVER use the stroller with roller skates, in-line skates, skateboards or bicycles.
-
NEVER allow your stroller to be used as a toy.
-
NEVER run or jog with this stroller.
ASSEMBLY
IMPORTANT ! To ensure safe operation of your product, please follow these
instructions carefully. Please keep these instructions for future reference.
IMPORTANT ! Before assembly and each use, inspect this product for
damaged hardware, loose joints, missing parts or sharp edges. NEVER use if any
parts are missing or broken.
IMPORTANT ! Adult assembly is required.
SET UP THE STROLLER FRAME
-
Release the fold latch by pulling it outward (Fig. 1a) and unfold stroller frame by pulling upward on the stroller handle until the frame locks (Fig. 1b).
Rear wheels assembly: -
The rear wheels MUST be installed prior to use.
-
Remove the pin and 1 washer from both ends of the rear axle (Fig. 2a).
-
Install the rear wheel with the auxiliary teeth inserting first (Fig. 2b).
-
Get the cross bar through the rear wheel and insert the second washer (Fig. 2c).
-
Place the pin horizontally into the hole of the axle bar and then rotate into a vertical position (Fig. 2d).
-
Align the tabs on the cap with the holes on the wheels. (2) Push the cap into the wheel to close the axle assembly.
NOTE: Press firmly with your palm to press the cap in completely (Fig. 2e). -
Repeat for the other side.
-
Place the rear legs over the axle with wheels and apply downward pressure on both sides. Ensure both sides lock into place (Fig. 2f).
NOTE: Pull on the front and rear wheels to ensure all are securely attached to the stroller. NEVER use stroller if wheels do not lock into place. If you need assistance, please contact our customer service department at 1-800-328-7363, Monday-Friday, between 8:00 a.m. and 4:30 p.m. PST. www.babytrend.com/contact- us
MOBILE PHONE INSET PARENT TRAY
WARNING: Do not place hot liquids or more than 3 lb (1,36 kg) in the
parent tray. Serious burns or unstable conditions can result.
WARNING: Care must be taken when folding stroller to prevent damage. Make
sure all accessories, mobile phones, diaper bags or purses are removed before
folding. Failure to remove items in, or on the stroller may result in damage
to the stroller or the item(s) if not removed. Baby Trend® will not be liable
or warrant any damage.
- To Insert Parent Tray: Locate the 3 open slots on the tray and face them toward the canopy.
- Align the parent tray tabs to the inner tabs on both sides of the stroller. Press the tray down firmly until both tabs click into position. See Diagram A.
Diagram A – Parent Tray Insertion Direction
REAR CANOPY ATTACHMENT TO PARENT TRAY
-
Insert the center elastic band into the tray. From the underside hook it to the tray tab. Repeat for the side elastic bands (Fig. 4a).
-
Underneath the frame secure the canopy sides with the bands (Fig. 4b). Fasten each hook and strap onto the stroller frame (Fig. 4c).
-
Pull the canopy edge forward or backwards to open and close (Fig. 4d).
-
Fold canopy visor out for additional shade or fold inward when not in use (Fig. 4e).
-
Parent tray removal: Remove the elastic bands by reversing Step 4 (Fig. 4a). Under the stroller frame locate the parent tray tabs. Press them inwards and lift up the tray from the housing (Fig. 4f).
Diagram B – Parent Tray Cut Away and Phone Accommodation
- Mobile phone Inset tray: Place mobile phone into the inset tray section. Ensure the phone gets accommodated correctly and rest it against the angle point of the tray. See Diagram B.
NOTE: The positioner may not accommodate all mobile phones or other devices. Do not use positioner as a secure holder when not in use or if your phone is loose or is too large.
CHILD TRAY
WARNING: The child’s tray is not a restraint device: always secure your child with the seat harness. DO NOT lift the stroller by the child’s tray. Use care when child is in the stroller and securing the front tray. Do not place hot liquids or more than 3 pounds (1.36 kg) in the child tray. Serious burns or unstable conditions could result.
- To attach the child tray: Push the tray downward into the connectors (Fig. 5a). Check that the tray is securely latched in place.
- To access the child seat: Push one release and lift up the tray simultaneously (Fig. 5b). Either side of the child tray will lift and rotate out of the way to allow access to the front seat.
- To remove the child tray: Push to release both ends and lift up the tray simultaneously (Fig. 5c).
STORAGE BASKET
-
Check Straps: Ensure that all straps with snap closures are attached correctly.
NOTE: Always secure straps as shown in (Fig. 6a). -
Basket Access / Flip-Up Leg Rest: Lift the leg rest to access the storage basket from the front side (Fig. 6b).
NOTE: Lift leg rest from the edge, and always close the storage basket front access when not in use.
REAR BRAKES
WARNING: Always set brakes when the stroller is not being pushed so that
the stroller will not roll away.
NEVER leave stroller unattended on a hill or incline as the stroller may
slide down the hill.
- Press down the brake levers to engage and lift up on the brake levers to release. The stroller may require forward or rearward movement in order to engage the brake. Check that the brakes are properly applied (Fig. 7).
SECURE THE CHILD
WARNING: Avoid serious injury from falling or Sliding out. Always use the
safety harness.
STRANGULATION HAZARD: Child can strangle in loose safety harness. Never
leave child in seat when safety harness is loose or undone.
- The shoulder straps of the 5-point harness have multiple positions. Select the position that places the shoulder strap level with, or below the top of the child’s shoulder (Fig. 8a).
SAFETY
- To secure the child, place the safety harness around the child’s waist and over the shoulders. Place the crotch strap between the child’s legs. Insert the male end of each shoulder/waist belt into the buckle on the crotch strap. Tighten all buckles to the proper fit for the child (Fig. 8b).
- To adjust the harness to the next height level pull the strap in a hoop form through the slot (Fig. 8c).
- To adjust the harness to a lower height level thread the clip back into the slot and pull it out through the desired lower level (Fig. 8d).
- RELEASE! Push button on center clasp, the two harness buckles will release (Fig. 8e).
SEATBACK POSITIONING
- To recline the seat, open the cover of the adjustment strap located on the right side of the frame. Loosen the strap to the desired position for the seat and close the cover.
- To place the seat into an upright position, open the cover and pull the adjustment strap to tighten, then close the cover (Fig. 9). The upright position should be used only for a child thatis
at least 6 months old. Always re-adjust the safety harness, including the shoulder belts, when repositioning the seatback.
THE INFANT CAR SEAT
WARNING: Avoid serious injury from falling or sliding out, always use the Infant Car Seat harness.
Infant car seat sold separately (visit babytrend.com for compatibility chart)
INFANT CAR SEAT
CS01 EZ-Lift, CS02 EZ-Lift PLUS and CS03 EZ-Lift PRO Infant Car Seats
-
- • Align the car seat module to the inner frame connectors. Carefully rest the car seats lower rear against the angle point of the tray. Latch the module into the stroller frame. Press down firmly for the click. ALWAYS ensure that the car seat is properly connected and locked onto the stroller before each use by lifting up on the car seat handle (Fig. 10a).
NOTE: To make seat position adjustments refer to step 9.
- • Align the car seat module to the inner frame connectors. Carefully rest the car seats lower rear against the angle point of the tray. Latch the module into the stroller frame. Press down firmly for the click. ALWAYS ensure that the car seat is properly connected and locked onto the stroller before each use by lifting up on the car seat handle (Fig. 10a).
REMOVING THE CAR SEAT:
- N OTE: Set handle to the carry position (Fig. 10b). Squeeze the release handle located at the Top-rear of the car seat and lift away from the stroller (Fig. 10c)
FEATURES
STROLLER HANDLE COVER FEATURE
- Zipper: To attach, wrap around the handle and zip closed (Fig. 11a). Unzip to remove (Fig. 11b).
NOTE: May be stored in the storage basket.
STORAGE POUCH
WARNING: The maximum weight that can be carried in the storage pouch is 12 lb. (5.44 kg).
-
Flip out the storage pouch by squeezing the adjustment buckle and pulling the strap down (Fig. 12a). Use the toggle to loosen and tighten the pouch (Fig. 12b).
-
To compress and close, tighten the pouch with the toggle (Fig. 12c). Close the entire storage pouch by squeezing the tabs and pull the adjustment buckle up (Fig. 12d).
IMPORTANT! : Always close and secure the pouch when not in use.
FOLD
TO FOLD STROLLER
WARNING: Care must be taken when folding and unfolding the stroller to
prevent finger entrapment.
WARNING: Care must be taken when folding stroller to prevent damage. Make
sure all accessories, mobile phones, diaper bags or purses are removed before
folding. Failure to remove items in, or on the stroller so may result in
damage to the stroller or the item(s) if not removed. Baby Trend® will not be
liable or warrant any damage.
CAUTION: Do not allow children near stroller while folding.
- Locate the strap in the seat pocket. Using one hand pull the strap firmly upward to unlock the frame (Fig. 13a).
- Holding the strap lift the stroller frame until it fully closes (Fig. 13b). Fold stroller to collapsed position (sometimes may require additional assistance by hand) before securing with fold latch (Fig. 13c).
- Always tuck the pull strap back into the seat fabric (Fig. 13d).
NOTE: You may remove the tray for a compact fold. Refer to Step 4 (Fig. 13e).
TO UNFOLD STROLLER
CAUTION: Do not allow children near.
- Unlock the fold latch (Fig. 14a) and unfold stroller frame by pulling upward on the stroller handle until the frame locks (Fig. 14b). Refer to the child tray instruction as needed for removing or adjusting the tray.
SECURING THE SEAT FABRIC
- If assembly required: Feed the rear recline clip and the seat fabric through the appropriate hook and loop slots on the stroller frame (Fig. 15a).
- Ensure the safety straps underneath the rear seat are secured through the appropriate slots (Fig. 15b).
MAINTENANCE
FRONT AND REAR WHEEL RELEASE
-
If replacing the front wheel: Locate the release pin on the front of the wheel hub. Push in the release pin and pull the wheel out (Fig. 16a).
-
Re-Install: Assemble the front wheels by inserting each to the pin. Press firmly to secure in place.
NOTE: Release pin faces inward if wheel is positioned as shown in (Fig. 16b). -
If replacing the rear wheel: Press the release pin and pull the wheel out (Fig. 16c).
CARE AND MAINTENANCE
SEAT PAD
- To clean the seat pad, use only mild household soap or detergent and warm water on a sponge or clean cloth.
OTHER
- Check your stroller for loose screws, worn parts, torn material or stitching on a regular basis. Replace or repair parts as needed.
BABY TREND® CUSTOMER SERVICE
The Customer Service Department can be contacted
at 1 800-328-7363 Monday through Friday
between
8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required prior to
returning product(s) to Baby Trend®.
References
- Baby Trend® | Car Seats, Strollers, High Chairs, Nursery and More!
- Limited Warranty Coverage – Baby Trend
- Baby Trend® | Car Seats, Strollers, High Chairs, Nursery and More!
- Contact Us – Baby Trend
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>