HD Ridez HW-WB-NT050 Blow Molding Running Boards Side Step Instruction Manual
- June 1, 2024
- HD Ridez
Table of Contents
HD Ridez HW-WB-NT050 Blow Molding Running Boards Side Step
Product Information
Specifications:
- Product Name: P1 Plastic Molded Running Board
- Compatibility: 04-15 Nissan, 17-24 Titan, 16-24 Titan XD Crew Cab
- Part Number: HW-WB-NT050
- Material: Plastic
- Includes: Running Boards, Mounting Brackets, Washers, Nuts, Bolts
Product Usage Instructions
Installation:
- Remove all contents from the box and verify all parts are present.
- Start installation at the front of the driver side of the vehicle and locate the factory threaded holes or stud.
- Select the appropriate Mounting Bracket and attach it to the mounting location following the instructions provided for models with or without threaded studs.
- Install Mounting Brackets at the designated locations along the body panel.
- Place the Running Board on top of the Brackets.
- Insert Double Bolt Plates into the channels in the bottom of the Running Board closest to the Brackets.
- Attach the Running Board to the Brackets using washers, lock washers, and nuts. Do not tighten hardware yet.
- Level and adjust the Running Board before tightening all hardware.
- Repeat the installation steps for the passenger side Running Board.
- Periodically inspect the installation to ensure all hardware is secure and tight.
To protect your investment, wax the product after installing. Regular waxing is recommended for added protection. Avoid using abrasive polishes or waxes that could damage the finish. Mild soap can be used for cleaning.
FAQ:
-
Q: How often should I wax the running boards?
A: Regular waxing is recommended to maintain a protective layer over the finish. Depending on usage and environmental conditions, waxing every few months should be sufficient. -
Q: Can I use a power washer to clean the running boards?
A: It is not recommended to use a power washer as it may damage the finish or dislodge hardware. Mild soap and water with a soft cloth are best for cleaning.
PARTS LIST
| 2 | 88” P1 Running Board | 12 | 8mm Lock Washers |
|---|---|---|---|
| 3 | Driver/Left Side Mounting Brackets | 6 | 8mm Nylon Lock Nuts |
| 3 | Passenger/Right Side Mounting Brackets | 6 | 6mm Double Bolt Plates |
| 12 | 8mm x 30mm Hex Bolts | 12 | 6mm x 22mm x 2mm Flat Washers |
| 6 | 8mm x 24mm x 2mm Flat Washers | 12 | 6mm Lock Washers |
| 6 | 8mm x 16mm x 1.6mm Flat Washers | 12 | 6mm Hex Nuts |
OVERVIEW
INSTALLATION INSTRUCTION
PROCEDURE:
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- Start installation at the front of the driver side of the vehicle and locate the factory threaded holes or stud located on the side of the inner body panel, (Figures 1—2). NOTE: Remove the plastic plug or any insulation on the side panel to locate the threaded oles.
- Select (1) driver side Mounting Bracket. Attach the Bracket to the mounting location with:
- a. Models with threaded stud: Attach Bracket to stud with (1) 8mm x 24mm STD Flat Washer and (1) 8mm Nylon Lock Nut. Next, insert (1) 8mm x 30mm Hex Bolt with (1) 8mm Lock Washer and (1) 8mm x 16mm Small Flat Washer through the remaining ower hole in the Bracket and into the threaded hole, (Figures 1 & 3). Do not tighten hardware at this time.
- b. Models without threaded stud: Attach Bracket to the upper threaded hole with (1) 8mm x 24mm STD Flat Washer, (1) 8mm Lock Washer and (1) 8mm x 30mm Hex Bolt. Attach Bracket to the lower threaded hole with (1) 8mm x 16mm Small Flat Washer, 1) 8mm Lock Washer and (1) 8mm Hex Bolt, (Figure 2 & 3). Do not tighten hardware at this time.
- There are (4) mounting locations along the body panel. Bracket installation will use the 1st, 2nd and 4th mounting locations. Repeat the appropriate Steps 2—4 to install the center and rear Mounting Brackets, (Figures 1 — 3). NOTE: The cradles on the ounting Brackets should be facing the rear of the vehicle when properly installed.
- Carefully unwrap and select the driver side Running Board. With assistance, place the Running Board on top of the Brackets.
- Select (3) 6mm Double Bolt Plates, (Figure 4).Locate the channels in the bottom of the Running Board. Insert the Bolt Plates into the channels in the bottom of the Running Board closest to the Brackets (Figure 5). Lift the Running Board up and guide the tuds through the Brackets.
- Attach the Running Board to the Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers and (6) 6mm Hex Nuts, (Figure 6).Do not tighten hardware at this time.
- Level and adjust the Running Board and tighten all hardware at this time.
- Repeat Steps 2—8 for passenger Running Board installation.
- Do periodic inspections of the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Board.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>