ESPERIA KRH-M202 Bluetooth/USB/MP3/WMA AM/FM Stereo Radio Owner’s Manual

June 6, 2024
ESPERIA

Owner’s manual
KRH-M202
12/24V Bluetooth®/USB/MP3/WMA
AM/FM Stereo Radio

Thank you for purchasing the ESPERIA product.
Please read this owner’s manual carefully before operating this unit.
Store it in safe place with this manual.

Operational Panel

  1. Power Button
    Press the Button to power ON. Press again to power OFF.

  2. LCD (Liquid Crystal Display)
    The receiving band and frequency or the current time will be indicated on the display.

  3. Clock (CLOCK ADJ.) [CLOCK, CLOCK ADJ. ] Button
    On Radio Mode, pressing this button will indicate the current time, and pressing it again will resume the frequency display.
    After 3 seconds, the time display will automatically change to the frequency display.
    Press and hold to enter in Clock Adjustment Mode.

  4. Scan [SCAN] Button
    By pressing and releasing the button the scan tuning will start automatically and the strong signal are memorized on memory.

  5. Tuning Buttons [TUNE∧,∨] By pressing the [TUNE∧] or [TUNE∨] button the receiving frequency will be up or down.
    By pressing the button for more than 2 second, the seek tuning will start.
    When the strong signal station is received the seek will stop.
    Please press the button again if you want to stop the seek tuning.

  6. Preset Memory Button[①~⑥] On each band (FM1, FM2, FM3 and MW), One station is memorized on the memory from channel 1 to channel 6.
    Refer to the section “Memorizing radio station to the memory”

  7. Bands Select Button [BAND] By pressing the button, the receiving band will be selected as shown.
    FM1→FM2→FM3→MW
    The receiving band and frequency will be indicated on the display.

  8. Volume Control Button [VOL+,-] By pressing the [VOL+] button, the sound volume will increase.
    By pressing the [VOL–] button, the sound volume will decrease.

  9. Bluetooth [B] button
    Press the button to connect to the last Bluetooth compatible device that has registered (Pairing).
    If you press and hold for 2 seconds or more, connection (registration) is released and the pairing standby mode is set.

  10. Bluetooth LED
    When this LED lights up, the Bluetooth device is connected. Flashes in pairing standby mode.

  11. Mode Select Button [MODE] Pressing the button, a source will be selected as shown.
    If USB memory is not connected, USB mode will skip after any second.
    FM or MW → USB → Bluetooth → AUX

  12. AUX-IN jack(Auxiliary Audio In Put)
    Open the rubber cap and connect the portable audio device by the cable the stereo mini-plug(3.5mm)
    Please cover the AUX-IN jack with the rubber cap dustproof or waterproof, when you do not need to connect the portable audio device.

  13. USB Input Terminal
    Open the rubber cap and connect a USB storage device.
    Please cover the USB input terminal with the rubber cap for dustproof or waterproof, when you do not need to connect the USB storage device.

Specifications

General
Power Source:DC12V~24V
Power Consumption: Less than 2A
Rated Output Power:16W + 16W(4Ω)
Normal Output Power:14W + 14W(10%TDH,4Ω)
Dimension:179(w)×50(H)×91(D)mm
FM section
Receiving Frequency Range: 87.5~108.0MHz(EU)
87.9~108.0MHz(USA)
Usable Sensitivity: 3µV(S/N 30dB)
S/N Ratio : 50dB
MW section
Receiving Frequency Range: 531~1602kHz(EU)
530~1710kHz(USA)
Usable Sensitivity:20µV(S/N 20dB)
AUX section
AUX IN: Stereo mini jack(φ3.5),
Rated Input Power:1V
Normal Input Power:90mV
Bluetooth
Specification: Ver5.0
Bluetooth Class: Class2
(Maximum Distance
10m) Frequency Range:2.402GHz~2.48GHz
Profile -2.32dBm(for EU):HFP V1.5,A2DP V1.2,AVRCP V1.0
USB
Specifications:USB2.0/1.0
Support Format
MP3:MPEG1,2,2.5
Audio Layer 2,3
WMA:Windows MediaTM Audio
Support File System :FAT16/FAT32 File system
Maximum Output :DC5V / 0.5A

Listening the radio

  1. Set the ignition key to ACC or ON and press the [POWER] button to turn on the radio.
  2. Select the desired band FM or MW by the [BAND] Button.
  3. Select the desired station by a [① to ⑥] button or a [TUNE] Button.
  4. To turn off the radio, press the [POWER] button.

Manual tuning

Press the [TUNE∧] or [TUNE∨] Button, the received frequency shifts one step.

SEEK tuning

Pressing the [TUNE] Button for 2 seconds or longer, the seek tuning will be started and stop at the available frequency.

Memorizing radio station to the memory

  1. Press the [BAND] button to select FM1, FM2, FM3, and MW , and select the desired station.
  2. Then search the desired station by the seek or the manual tuning.
  3. Press any button (from ① to ⑥) for 3 seconds or longer.
  • The preset channel number will be indicated on the display.
  • ON each band ( FM1, FM2, FM3, and MW ), 1station can be put on the memory on each of the buttons from ① to ⑥.

Auto Store Memory (SCAN)

During the radio mode, by pressing and releasing the [SCAN] Button will automatically store a strong signal station in memory from channel 1 to channel 6.
NOTE :
By this operation, the current data in the memory will be erased.
When the expected radio station is not be able to store in the memory by the SCAN function, Please store the radio station in the memory manually.

USB Operations

Connect a USB storage device to USB socket on the this unit.
Press the [MODE] Button and select the USB Playback Mode.
During the USB Playback Mode. “USB”will be indicated on the display.
During playback, follow the instruction below to control playback.

  1. Previous Track[ ] Button
    Skip to the previous track. Press and hold this button to rewind fast-rewind.

  2. Play/Pause[ ] Button
    Pause or resume playback.

  3. Stop [ ] Button
    Stop playback.
    Press the Play Button, playback starts at the top of current track

  4. Next Track[ ] Button
    Skip to the next track. Press and hold this button to rewind fast-forward.

  5. Repeat [ ] Button
    Repeat the current track and Press the Repeat Button again, turn off the Repeat Mode.
    NOTE :

  • Please connect/uncomment the USB storage device in a other than USB mode.
  • ESPERIA does not guarantee compatibility with all USB storage device
  • Be sure to use the extension cable for the USB socket.
  • Please do not connect to other than USB memory device. Can not charge the smartphone.
  • ESPERIA cannot be liable for any data loss or damage and improper access of USB storage devices.

Using Bluetooth wireless technology

Mobile phones and audio devices that support Bluetooth can be connected to use with this unit.
You will be notified that there is an incoming call by connecting the mobile phone.
※This unit will not support calls for the reason of No microphone is installed.
In order to use Bluetooth devices must be able to match certain profiles. this unit is compatible with the following profiles.
Incoming mobile phones
HFP(Hands-Free Profile)
Bluetooth audio
A2DP(Advanced Audio Distribution Profile)
AVRCP(Audio/Video Remote Control Profile)
Note: The Bluetooth word mark and logos are owned by the Bluetooth SIG, inc. and any use of such marks by ESPERIA Co.,Ltd Is under licensed. Other trademarks and trade names are those of their respective owners.

Pairing Bluetooth devices

When connecting a Bluetooth device for the first time, mutual registration is required.
Pairing enables this unit and other devices to recognize each other.
※Please first enable the Bluetooth function of the Bluetooth device before pairing.
For details, please refer to the manual of the Bluetooth device.

  1. Press the [MODE] button to select the function Bluetooth mode.

  2. Enable Bluetooth on the Bluetooth device.

  3. Press and hold the Bluetooth Button until the sounds are connected. (tow beep sounds)
    ※When “P” flashes on the display, it is in pairing standby mode.

  4. Select “CAR RADIO” with a Bluetooth device.

※Only one pair of Bluetooth devices can be paired with this unit. If you want to pair other devices, repeat steps 1 to 4 again.
CAUTION: There is a function to reconnect to the last connected device by turning the power on.
Prevent incorrect connection when leaving this unit in (car etc.),
Press and hold the Bluetooth button until it sounds”beep”, then please release the pairing.

Play audio of Bluetooth device

If you have already registered (pairing) in the Bluetooth device, make sure that the Bluetooth
LED is turning on light. Press the [MODE] button to switch to the BT mode.
In BT mode Bluetooth device can be operated with ① to ⑤ buttons.

  1. Previous Track[ ] Button
    Return to the beginning of the current track.
    Press the button again to skip to the previous track.

  2. Play/Pause[ ] Button
    Pause or resume playback.

  3. Stop [ ] Button
    Music that is playing stops.

  4. Next Track[ ] Button
    Skip to the next track.

  5. Repeat [ ] Button invalid in Bluetooth mode.
    CAUTION: In case no sound is detected from this unit, please see to it that the Bluetooth compatible device music output destination is in “CAR RADIO” Please check.

Bluetooth device incoming call

If the Bluetooth device has already been connected (Bluetooth LED is lit), this unit is in standby mode for incoming calls.
When receiving a call, “CALL” appears on the liquid crystal display, the volume of the car stereo
automatically mutes, and the ringing tone of the phone is played from the speaker.

AUX Function

  • This radio has an AUX input jack for a portable device.
  • Be sure to use the cable stereo mini-plug(3.5mm)for the AUX-IN jack.
  • Press the [MODE] button and select the AUX mode.
  • During the AUX mode, “AUX” will be indicated on the display.
  • The volume controls of the portable devices should be adjusted approximately the same as currently portable audio devices should be adjusted approximately the same as currently listening radio sound volume level.
  • Volume control buttons are able to control the sound with this unit

Resetting the radio

Please reset this device in trouble such as when the frequency display is different and when switching is impossible etc. Hold down the Bluetooth button and press the power button.

Troubleshooting

General

Problem Cause Measure
Nothing happens when buttons are pressed. the display is not accurate. CPU
malfunction due to noise etc. Reset this unit according to “Resetting the

radio”.
After resetting, preset memory etc. all disappear, please set again.

Radio

Problem Cause Measure
Sound is noisy It is not on the frequency of the broadcasting station Please

adjust to the correct frequency.
The antenna does not extend (when using pillar antenna)| When using a radio, please use the pillar antenna extend.
The antenna is not ground- S or not installed properly| Please consult your dealer.
Antenna power supply not connected| The booster built-In antenna needs to connect the power supply to the antenna.
For details, please consult your dealer.
Display unusual frequencies| CPU malfunction due to noise etc.| Reset this unit according to “Resetting the radio”.
After resetting, preset memory etc. all disappear, please set again.

USB Playback

Problem Cause Measure
No sound heard The USB storage device contains no MP3/WMA files. Record

MP3/WMA files properly to the USB storage device.
The files are not in proper MP3/WMA format.| Use only properly encoded MP3/WMA files.
Sound is
Interrupted or has noise.| The MP3/WMA
Files are improperly Encoded.| Use only properly encoded MP3/WMA files.
The device isn’t recognized| The device is Damaged.| Disconnect the USB storage device and reconnect. If the device is still not recognized, try replacing it with a different device.
Connectors are loose.
The USB memory is not formatted with FAT32 / FAT16| Format the USB storage device with the FAT32 / FAT16 file system and write the MP3 / WMA file.
Be sure to back up the USB memory before formatting.

Bluetooth

Problem Cause Measure
Can not connect a Blue. tooth device Bluetooth connection is not established

Depending on your Bluetooth device, some items that take time to connect may not be automatically reconnected.
Please check the Bluetooth LED,
if it does not turn on the light on time, please pair again according to “Pairing Bluetooth devices”.
Another Bluetooth device is connected.| If another Bluetooth device is connected, pair it again according to ‘Pairing Bluetooth device”.
Cannot remotely control Bluetooth devices.| AVRCP profile is not connected| Please disconnect all connected Bluetooth devices and pair it again according to “Pairing Bluetooth device.
The connection link be-tween devices may be broken| Again according to “Pairing Bluetooth device”.
does not support AVRCP| Please check the support profile of the Bluetooth device..
No sound heard| Bluetooth device volume is low| The volume of the Bluetooth device will be affected. Please set the volume of the Bluetooth device to an appropriate value.
The output destination of the Bluetooth device is not set to “CAR RADIO”| Please confirm that the Bluetooth device music output destination is in the “CAR RADIO”
Can not talk on the phone| This unit does not support Bluetooth calling.
Depending on the model of the mobile phone, you may connect to this unit with the call profile.| Please change the microphone setting from this unit to the mobile phone microphone on the call screen accord. ing to the instruction manual of your mobile phone.
Bluetooth audio playback stops after incoming call| Audio may not resume after a phone is interrupted.| After the call ends, please again according to “Pairing Bluetooth device”.

Manufacturer Hidaka Corporation
Factory Address:
203, East of Building 1, Paibang Jialian Industrial Area, Silian
Community, Henggang Street, Longgang District, Shenzhen
City, Guangdong Province, P.R.China

Declaration of conformity
We use this model KRH-M505
In accordance with the provisions of the 2014/53/EU and 2011/65 EU directives, we have established basic requirements and other relevant rules.

FCC 15B ClassB
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one ore of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

IC
This device complies with Industry Canada’s license-exempt RSS. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Co.,ltd.
2-8-85,YOSHINODAI,KAWAGOE-CITY SAITAMA-PREF.,JAPAN
TEL:+81-49-226-9120 FAX:+81-49-226-9136

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals