HD Ridez WB-FR175BD Overland Slider Drop Steps Instruction Manual
- June 1, 2024
- HD Ridez
Table of Contents
HD Ridez WB-FR175BD Overland Slider Drop Steps
Product Information
Specifications:
- Product Name: RS6 Overland Drop Step Running Boards
- Compatibility: 2022-2024 F150 Lightning, 2015-24 F150, 2017-24 F250-350 SuperCrew Cab
- Part Number: WB-FR175BD
Product Usage Instructions
Parts List:
- 1 Driver/Left Tube
- 1 Passenger/Right Tube
- 4 Drop Steps
- 6 Mounting Brackets
Installation Procedure:
- Start the installation under the Passenger/Right side of the vehicle.
- Locate the front factory mounting location along the inner side of the body and prepare the studs.
- Slide Plastic Washers over the factory mounting studs to prevent corrosion.
- Attach Mounting Brackets to the studs using Flat Washers and Nylon Lock Nuts.
Cleaning and Maintenance:
To protect your investment, avoid using polish or wax with abrasives. Clean
the Running Boards with mild soap only.
Frequently Asked Questions (FAQ):
-
Q: How do I know if all parts are present?
A: Before starting the installation, verify all parts listed in the manual are present in the package. -
Q: Can I install the running boards alone?
A: While it’s recommended to seek assistance, experienced DIYers may be able to install them alone following the instructions carefully.
PARTS LIST
| 1 | Driver/Left Tube | 12 | 10mm Nylon Lock Nuts |
|---|---|---|---|
| 1 | Passenger/Right Tube | 8 | 8mm x 25mm Double Bolt Plates |
| 4 | Drop Steps | 18 | 8mm x 24mm OD x 2mm Flat Washers |
| 6 | Mounting Brackets | 16 | 8mm x 22mm OD x 2mm Flat Washers |
| 12 | 10mm x 30mm Hex Bolts | 34 | 8mm Nylon Lock Nuts |
| 24 | 10mm x 20mm OD x 2mm Flat Washers | 18 | 8mm Plastic Retainers |
OVERVIEW
INSTALLATION INSTRUCTION
PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. ASSISTANCE IS RECOMMENDED.
-
Start the installation under the passenger/right side of the vehicle. Locate the front factory mounting location along the inner side of the body, (Figure 1). Use a wire brush or thread chaser die to remove excess paint and/or undercoating from all studs.
-
Slide (1) Plastic Washer over each of the (3) factory mounting studs in the body panel, (Figures 2 & 3).
IMPORTANT: The Plastic Washers are designed to prevent corrosion between the aluminum body panel and the steel mounting brackets. Do not install the Brackets without the Plastic Washers. -
Select (1) Mounting Bracket, (Figure 4). Attach the Bracket to the (3) studs on the rocker panel with (3) 8mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Figures 4 & 5). Do not tighten hardware.
-
Repeat Steps 2 & 3 to attach (2) Mounting Brackets to the center and rear mounting locations.
-
Select the Passenger/Right Tube. Insert (2) 8mm Double Bolt Plates into the front (2) sets of (2) holes, (Figure 6). Attach (1) Drop Step to the (2) Double Bolt Plates with (4) 8mm Flat Washers and (4) 8mm Nylon Lock Nuts, (Figure 7). Do not tighten hardware.
-
With assistance, line up the mounting tabs in the passenger/right Tube to the rear faces of the Mounting Brackets. Secure the Tube to the Mounting Brackets with (6) 10mm Hex Bolts, (12) 10mm Flat Washers and (6) 10mm Nylon Lock Nuts, (Figure 8). Do not tighten hardware.
-
Level and adjust the Running Board, then tighten all hardware.
-
Repeat Steps 1—7 to attach the Driver/Left Running Board.
-
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Use only mild soap to clean the Running Boards.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>