Maxxima MRL-S61585 6 Inch Fire Rated Slim Panel LED Installation Guide
- June 1, 2024
- Maxxima
Table of Contents
Maxxima MRL-S61585 6 Inch Fire Rated Slim Panel LED
Specifications
- Model: MRL-S41285, MRL-S61585
- Electrical Parameters:
- Input Voltage (V): 120
- Input Frequency (Hz): 60
- Input Current (A): (Varies by model)
- Input Watts (W): (Varies by model)
FAQ
Q: Can this product be used with emergency exit fixtures?
A: No, this lamp is not intended for use with emergency exit fixtures or
emergency lights.
Q: What should I do if there are exposed bare wires?
A: Ensure no bare wires are exposed outside the wire nut connectors. Do not
make or alter any open holes in an enclosure of wiring or electrical
components during installation.
WARNING / ATTENTION
- Risk of fire. Supply conductors (power wires) connecting to the fixture must be rated at 90° C. If uncertain, consult an electrician.
- Risk of fire or electric shock. LED installation requires knowledge of luminaries’ electrical systems
- Risk of fire or electric shock. If not qualified, do not attempt installation. Contact a qualified electrician.
- Risk of fire or electric shock. Install this kit only in the luminaires with the construction features and dimensions shown in the photographs and/or drawings.
- To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
- This lamp is not intended for use with emergency exit fixtures or emergency lights.
CAUTIONS
- For your safety, read and understand the instructions completely before starting installation.
- Before attempting installation, check your local electrical code, as it sets wiring standards for your locality.
- Suitable for wet locations. Covered ceiling mount only.
NOTES
- If the luminaire (fixture) is to be switched from a wall switch, make sure the black power supply wire is connected to the switch. DO NOT connect the white supply wire to the switch.
- Make sure no bare wires are exposed outside the wire nut connectors.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.
Hole Cutout Diameter
| Model | Hole Cutout Diameter (inches) | Hole Cutout Diameter (mm) |
|---|---|---|
| MRL-S41285 | 4.25″ | 108 |
| MRL-S61585 6.25″ | 158 |
Drawing
Electrical parameters
Model| Driver/Junction Box I nput Voltage (V)| Input Frequency
(Hz)| Input Current (A)| Input Watts (W)
---|---|---|---|---
MRL-S41285| 120| 60| 0.104| 12
MRL-S61585 120
60 0.116| 15
Installation Guide
-
Turn off the power before installation. Remove the existing fixture if applicable.
-
Determine the location and necessary hole cutout diameter using the supplied table and cut the ceiling hole with the listed approximate diameter (Fig. 1).
-
Open the power supply/junction box cover and remove the appropriate knockout(s) on the side panel. Install
the appropriate cable clamp(s) (not included or necessary) and insert the electrical supply cable through the clamp or knockout. Connect the ground (green or bare copper) wire to the green wire, the hot wire to the black supply wire, and the neutral wire to the white supply wire using the supplied wire nuts. -
Place all wiring and connections back into the box and close the cover.
-
Use the CCT color switch on the outside of the power supply/junction box (Fig. 2) to preview and select the desired color temperature.
-
Insert the power supply/junction box through the mounting hole (Fig. 3) and secure it.
-
Push the spring-loaded clips into the mounting hole upwards and insert the LED panel. Release the clips and the fixture will be pulled flush to the ceiling (Fig. 4).
Three Year Warranty
Maxxima extends a 3-year limited warranty to the original purchase that the products listed are free from defects in material and/or workmanship only. Maxxima will replace any warrantied product with the original consumer/purchaser if the product fails because of defects due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume any obligation whatsoever beyond sending a free replacement product.