Maxxima MRL-S61230DW 4 Inch Round Slim LED Flat Panel Installation Guide

: May 15, 2024
: Maxxima

Table of Contents

Mobile APP Set-up
Mobile APP operation

Maxxima MRL-S61230DW 4 Inch Round Slim LED Flat Panel Installation Guide

Productname: 4″ WiFi Siim Round LED Downlight 10W
Productname: 4″ WiFi Siim Round LED Downlight 10W
ModelNo: RL-541030DW
Rated Votage: 120VAC
WILM/CRI: 10W 600LM >80
CCRange: Ros + 2700 – 650K

WARNINGS AND CAUTIONS

Risk of fire and electrical shock, products should be installed in accordance with appropriate electrical codes and regulations
The product shall be used together with an upstream air-gap switch
If you are unsure about any part of these instructions, consult a licensed electrician
DO NOT USE WITH AN IN-WALL DIMMER. Only Dimmable via the mobile APP.

This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION

Any changes or modifications to this unit not expressly approved by the manufacture could void the user’s authority to operate the equipment.

Mobile APP Set-up

Step 1 Download the “Smart Life” App

Scan the QR code below to download the “Smart Life” App
You can also download this app in the app store/Android app market search “Smart Life”

Step 2 Register an account and Login

Open the Smart Life App, click Register to create an account & login.
If already registered, login.

Step 3 Selecting the Device

Click ‘Add Device’ or the + ‘in the top right-hand corner;
Click ‘lighting’ then to enter the device connection interface;

Step 4
Mobile phone connection
Step 4a Ez mode connection:

When the Slim Panel is on, switch the on/off switch 3 times (each interval within 1s), Off, On, Off, On, Off, On. The light will flash quickly (flash once every second), your device can connect to the light. The light will stop flashing once when the connection is successful. If there is no connection, device will exit network configuration mode after 3 min.

Enter the Wi-Fi password in your home and click waiting for the connection.
Confirm the Status indicator flashes quickly click

Step 46 AP mode connection:
When the Slim Panel is flashing quickly, turn the light off. Repeat turn the on/off switch 3 times to make the light flash slowly. The light will flash slowly (flash once every 2-3s), your phone can connect to the light. The light will stop flashing once when the connection is successful. If there is no connection, the device will exit network configuration mode after 3 min.

Click ‘APMode’ to enter the operation interface.
Confirm the light flashes slowly, dick
Enter the Wi-Fi Network and password, click
Click connect to the Wi-Fi that comes with the light and return to the APP, wait for the connection.
Click to enter the operation interface.

Mobile APP operation

Select White to adjust the CCT and to Dim
Select Color o adjust to the desired color, to Dim and adjust Contrast.
Click Schedule to set a on or off function of the light at a certain time/day(s)
Add schedule and then save. Repeatas desired

Mobile APP operation

Select Left Time to enable Countdown Timer when Light is on The time selected will automatically tum the light off after the desired time.
After the light connection is completed, it can be shared to many people, that is, one light can be controlled by multiple Users.
Click to enter the device details interface;
Click ‘Share Device’ to enter the device sharing interface.
Click “Add Sharing’, add the account you are willing to sharing
You may also share all devices in your account with another account
Go to “Me” at the bottom of the App
Select”Home Management”
Select the Home you wish to share with
Select “Add Member. You can send the invite via your Smart Life account, Message, or Email. New Members must have or create a • Smart Life account via the Smart Life App

Blue Tooth capability Instructions

When the smart lights’ internet connect was cut down, they can’t be controlled by app at the moment. But after 3-5mins, the smart lights will automatically switch to the Bluetooth control mode. At this time, you will still be able to control the product in a short distance through your mobile phone’s Bluetooth.

Note:

Make sure your phone has turned on the Bluetooth switch.
The product has been paired in your mobile phone and has not been deleted from the app.
Keep your mobile phone connected to the internet

Support Amazon Alexa and Google Home Set-up

For Amazon Alexa

Open the Alexa app and select “Skills” from the top menu On the Skills page, search for Smart Life
Enable Smart Life in the Alexa App
Log in with your Smart Life Account (username & password) • Discover new smart devices in the App or ask Alexa to discover new devices
For Google Home
Open the Google Home App and tap the “+” icon in the homepage
Select “Set up device” in the “Add and manage” Screen In the “Set Up” screen, tap “New Devices” to set up new devices in your home
Tap “Works with Google” to authorize Google Home to work with your Smart Life account

Amazon Alexa and Google Home voice control examples

For Amazon Alexa

Alexa, turn on
Alexa, turn off
Alexa, set to percent
Alexa, brighten/increase
Alexa,dim/decrease

For Google Home

Hey Google, turn on
Hey Google, turn off
Hey Google, is on/off?
Hey Google, brighten/increase <device name)
Hey Google, Dim/Brighten by 50%

TroubleShooting/Recommendations/Tips

If the light is offline in the App, make sure the in-wall switch is in the On position. If not, turn on.
Please check whether the light is connected with power, and your mobile device is connected to a 2.4GHz WiFi Network.
Check the router. If the router is dual-band, make sure to select 2.4GHz network to add the light. Router Broadcast should be set to open. Also try disabling the SGHz band temporarily on the router.
Make sure the WiFi User Name and Password are correct.
Make sure the light is within the range of the router signal. If not, try moving closer to the router. Check Wi-fi signal on the mobile device to make sure the signal is strong in that area or if it is weak.
Check to see if the maximum number of devices/lights the router can handle has been reached. If so, remove a device/light and restart the router. If there is no Wi-Fi connection, try restarting the light and/or restarting the router.
If the device will not go into pairing mode, try the on/off sequence 4 or 5 times instead of 3 times. Also give a second or 2 longer delay between the on/off sequence.
If the internet signal/connection from the internet provider is down, the light can still be controlled through the mobile device as long as both are connected to the same Network (Intranet).
If the internet signal/connection is down from your router, this light has a backup bluetooth function that will allow you to control the lights from a certain distance. Ensure bluetooth is enabled on your device.
For additonal troubleshooting tips, visit the webpage listed below https://www.maxximastyle.com/wifi-help

3 YEAR WARRANTY

Maxxima extends a 3 year limited warranty to the original purchase that the products listed are free from defects in material and/or workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of defects due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume any obligation whatsoever beyond sending a free replacement product.

WARNING / ATTENTION

Risk of fire. Supply conductors (power wires) connecting to the fixture must be rated 90°C. If uncertain, consult an electrician
Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaries electrical systems.
Risk of fire or electric shock. If not qualified, do not attempt installation. Contact a qualified electrician
Risk offire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects
This lamp is not intended for use with emergency exit fixtures or emergency lights.

CAUTIONS

For your safety read and understand instructions completely before starting installation.
Before attempting installation, check your local electric code, as it sets wiring standards for your locality.

NOTES

If luminaire (fixture) is to be switched from a wall switch, make sure black power supply wire is connected to the switch. DO NOT connect the white supply wire to the switch.
Make sure no bare wires are exposed outside the wire nut connectors.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kits installation.

Hole Cutout Diameter

The Hole Cutout Diameter size is 4.25″ or 108mm

Parts List
Product Overview

DRIVER/JUNCTION BOX
LIGHT PANEL
SPRING-LOADED CLIPS
CONNECTOR

Installation Guide:

Tum off the power before installation. Remove the existing fixture if applicable.
Determine the location for installation and cut ceiling hole with an approximate diameter of 4.25″ or 108mm (Fig. 1)
Open the DRIVER/JUNCTION BOX cover and remove the appropriate knockout(s) on the side panel (Fig. 2).

Install the appropriate cable clamp(s) (not included) and insert the electrical supply cable through the cable clamp. Connect the ground wire to the green wire terminal, hot wire to the black wire terminal and neutral wire to the white wire terminal using the wire nuts provided
Place all wiring and connections back into the box and close the cover Connect the DRIVER/JUNCTION BOX to the Tight panel using the CONNECTOR
Insert DRIVER/JUNCTION BOX through t mounting hole (Fig. 3)

and secure using mounting tabs
Push the SPRING-LOADED CLIPS into the mounting hole upwards and insert LIGHT PANEL into it. Release the dips and the fixture will be pulled flush to the celing (Fig 4)

Three Year Warranty:

Maxxima extends a 3 year limited warranty to the original purchase that the products listed are free from defects in material and/or workmanship only. Maxxima will replace any warrantied product to the original consu consumer purchaser if the product fails because of defects due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume any obligation whatsoever beyond sending a free replacement product.

info@maxximastyle.com
866.MAXXIMA (629-946)
www.maxximastyle.com
125 Cabot Court Hauppauge, NY 11788

Maxxima Logo