RYOBI RPS80 Cordless Palm Sander Instructions

: June 9, 2024
: RYOBI

Table of Contents

INTENDED USE
SANDER SAFETY WARNINGS
RESIDUAL RISKS
RISK REDUCTION
MAINTENANCE
SYMBOL
SYMBOLS IN THIS MANUAL
Documents / Resources

RPS80 Cordless Palm Sander RYOBI RPS80 Cordless Palm
Sander Instructions

Important!
It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.
Safety, performance, and dependability have been given top priority in the design of your palm sander.

INTENDED USE

The palm sander is intended for sanding and fi nishing metal, wood, plastic or similar materials using the abrasive pads or sheets provided. The palm sander is intended to be used by adult operators who have read the instruction manual and understand the risks and hazards. The palm sander should only be used in well ventilated areas. The palm sander is designed for dry sanding only.
The palm sander is intended only for consumer use.
Do not use the product in any way other than those stated in Intended Use. Use of the product for operations different from intended could result in a hazardous situation.

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

SANDER SAFETY WARNINGS

Always wear safety goggles and a dust mask when sanding, especially sanding over-head.
The machine is not suitable for wet sanding.
Do not use sanding paper larger than needed. Extra paper extending beyond the sanding pad can also cause serious lacerations.
The dust collection box shall be equipped with thetool. It should be emptied frequently. To connect dustcollection box, insert the adapter of dust box to the dustcollection opening on the rear end of the sander.

WARNING
Do not throw sanding dust into an open fire because materials in fine particle form may be explosive.

WARNING
A suitable breathing respirator must be worn while sanding lead paint, some woods and metal to avoid breathing the harmful/toxic dust or air.

WARNING
Dust from certain paints, coatings, and materials may cause irritation or allergic reactions. Dust from wood, such as oak, beech, MDF, and others are carcinogenic.
Materials containing asbestos should only be worked on or processed by qualifi ed specialist operators.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise and the operator should pay special attention to avoid the following:

Injury caused by dust
– Using the product will produce considerable amount of dust and fine particles. Use the dust collection device or connect a dust extraction vacuum when operating the product. Wear dust masks containing filters appropriate to the materials being worked on.
Ensure adequate workplace ventilation. Do not eat, drink, or smoke in the work area.
Injury caused by noise and vibration
– Wear ear protection during the sanding operation.
Do not operate the product for long periods of time.
See “Risk reduction”.

RISK REDUCTION

It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness and blanching of the fi ngers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:

Keep your body warm in cold weather. When operating the unit wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
After each period of operation, exercise to increase blood circulation.
Take frequent work breaks. Limit the amount of exposure per day.
If you experience any of the symptoms of this condition, immediately discontinue use and see your doctor about these symptoms.

WARNING
Injuries may be caused or aggravated by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

KNOW YOUR PRODUCT See page 87.

Switch off
Switch on
Cover
Finger pad
Lock
Dust collection box
Quick change hook-and-loop pad
Finger adhesive sandpaper
Delta adhesive sandpaper

SANDPAPER SELECTION
Selecting the correct size, grit and type of sand paper is an extremely important step in achieving a high quality sanded fi nosh. Aluminium oxide, silicon carbide, and other synthetic abrasives are best for power sanding. Natural abrasives, such as fl int and garnet are too soft for economical use in power sanding.
In general, coarse grit will remove the most material and fi ner grit will produce the best fi nish in all sanding operations. The condition of the surface to be sanded will determine which grit will do the job. If the surface is rough, start with a coarse grit and sand until the surface is uniform.
Medium grit may then be used to remove scratches left by the coarser grit and fi ner grit used for fi nishing of the surface. Always continue sanding with each grit until surface is uniform.

WARNING
Do not use sander without sandpaper; doing so will damage the cushion.

Sheet/pad recommended use

80-grit sanding sheet	Coarse sanding
120-grit sanding sheet	Light sanding
150-grit sanding sheet	Light sanding

MAINTENANCE

WARNING
The product should never be connected to a power supply when assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product from the power supply will prevent accidental starting that could cause serious injury.

When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic.
Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.
If the power supply cord is damaged, it must be replaced only by the manufacturer or by an authorized service center to avoid risk. Contact authorized service center.
For greater safety and reliability, all repairs should be performed by an Authorised Ryobi Service Centre.

**WARNING**
Electrical tools used on fi berglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fi berglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. We do not recommend using the product for extended work on these types of materials.

**WARNING**
Do not use compressed air to blow dust from the product.
This practice is dangerous and can cause dirt and grit to be blasted into someone’s eyes, causing injury.

LUBRICATION
All of the bearings in the product are lubricated with a suffi cient amount of high grade lubricant for the life span of the product under normal operating conditions. Therefore, no further lubrication is required.

CLEANING THE SANDING SHEETS
The sanding sheets that come with the product are made to be re-used. Therefore, it is important that they be cleaned periodically to remove sanding residue and foreign material that can accumulate over time.
To clean sanding sheets, rub the sheets with a hard rubber block. You can also use the clean rubber sole of a shoe.

ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environment-friendly recycling.

SYMBOL

| Safety Alert
---|---
V| Volts
Hz| Hertz
| Alternating Current
W| Watts
no| No-load speed
min־¹| Revolutions or reciprocations per minute
| Orbital Diameter
| CE Conformity
| EurAsian Conformity Mark.
| Ukrainian mark of conformity
| Class II tool, double insulation
| Wear ear protection
| Wear eye protection
| Please read the instructions carefully before starting the machine.
| Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

SYMBOLS IN THIS MANUAL

| Connect to the power supply.
---|---
| Disconnect from the power supply.
| Parts or accessories sold separately
| Lock
| Unlock
| Note
| Off
| On
| Without force
| With force

The following signal words and meanings are intended to explain the levels of risk associated with this product:
DANGER
Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
**WARNING
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
CAUTION**
(Without Safety Alert Symbol) Indicates a situation that may result in property damage.

EC declaration of conformity
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product
Palm sander
Brand: Ryobi
Model number: RPS80 / RPS100
Serial number range:
RPS80: 46222301000001 – 46222301999999
RPS100: 46222401000001 – 46222401999999
is in conformity with the following European Directives and harmonized standards 2006/42/EC, 2014/30/EU, 2011/65/EU
EN55014-1:2006+A1:2009+A2:2011, EN55014-2:2015, EN61000-3-2:2014,
EN61000-3-3:2013, EN60745-1:2009+A11:2010, EN60745-2-4:2009+A11:2011
RoHS documentation is compiled according to EN 50581:2012

Andrew John Eyre (BEng, CEng, MIET)
Vice President, Regulatory & Safety
Winnenden, May 05, 2017
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany

https://tm.by
VIHTepHet Mara3unH TM.by

Documents / Resources

| RYOBI RPS80 Cordless Palm Sander [pdf] Instructions
RPS80 Cordless Palm Sander, Cordless Palm Sander, RPS80 Palm Sander, Palm Sander, Sander, RPS80, RPS100
---|---