SCANSTRUT SC-MULTI-F2 Flip Pro Duo Instruction Manual

SCANSTRUT SC-MULTI-F2 Flip Pro Duo

Product Information

Specifications

• Product Name: FLIPP PRO DUO UUSSBB-AA & UUSSBB-C WWIITTHH 112V PPOOWER SOCKKEETT (SC-MULTI-F2)
• Input Voltage: 12V
• Input Current Max: 6A
• System Compatibility: 12V system, 24V system, 10-32V DC
• Output Types:
  • USB-AA: 5V-3A, 9V-3A, 12V-3A
  • USB-CC: 5V-3A, 9V-3A, 12V-3A
  • USB-A: 5V-3A, 9V-3A, 12V-3A
  • USB-C: 5V-3A, 9V-3A, 12V-3A, 15V-3A, 20V-3A
• Standby Draw: Low power consumption in standby mode
• Waterproof Rating: Waterproof

FAQ

• Q: What should I do if the charger is not working?
  • A: Check the connection to the power socket and ensure the input voltage is correct. Try using different devices to confirm if it’s a charger issue.
• Q: Is the charger compatible with both USB-A and USB-C devices?
  • A: Yes, the FLIPP PRO DUO UUSSBB charger supports both USB-A and USB-C devices with appropriate output voltages.

Technical Information

| USB Charger| 12V Socket
---|---|---
Input voltage| 12/24V system 10-32V DC| 12V system 10-15V DC
Input current max| 6A| 10A

Output type

| (12V system)| (24V system)|

12V⎓10A

USB-A| USB-C| USB-A| USB-C

5V⎓3A,

9V⎓3A,

12V⎓3A MAX

|

5V⎓3A,

9V⎓3A,

12V⎓3A MAX

|

5V⎓3A,

9V⎓3A,

12V⎓3A MAX

| 5V⎓3A,

9V⎓3A,

12V⎓3A

15V⎓3A,

20V⎓3A MAX

Standby draw| < 0.1W
Waterproof rating| IPX4 front-only lid closed

Parts And Tool

Parts list:

Tool list:

• READ IMPORTANT SAFETY INFORMATION BEFORE INSTALLING.
• For the latest tech info visit: www.scanstrut.com/USB

Installation Instructions

• Draw a centre line to align template, ensure line is square on surface and correct orientation.
• Use drilling template to drill x2 Ø32mm (1 1/4”) holes (see tools required).
• Feed barrels through the gasket and holes.
• REAR INSTALL ONLY
  • Tighten lock rings onto product until secure.
• FRONT INSTALL ONLY
  • Push bezel onto the product, make sure the bezel orientation is correct.
• FRONT INSTALL ONLY
  • Drill 4 pilot holes for bezel.
• FRONT INSTALL ONLY
  • Apply silicone seal on fixings and pilot holes.
• Connect to 12V supply, ensuring a waterproof connection. Fuse and select cable diameter according to input voltage and current for your specific installation.
  If using a 24V system a voltage converter is required on the 12V socket only

Drilling Template

WARNING CHECK SCALE

WARNING

• This product is to be connected to a 12V DC or 24V DC battery power source only. The power supply must be switched off before installation.
• • An appropriate fuse or circuit breaker must be used between the battery / power source and this product. Check for correct polarity of all wiring before switching the power on.
• This product may contain high voltages. Do not tamper with the product.
• This product is NOT approved for use in hazardous/ flammable atmospheres.
• DO NOT install in a hazardous/flammable atmosphere e.g. engine room.
• Before drilling any holes, ensure the area behind the mounting location is clear of wires, fuel and all other hazardous objects.
• Ensure any holes cut will not significantly weaken the structure of the mounting surface.
• If the product needs to be mounted outside, it must be mounted in a location safely above the waterline, where it is not at risk of being submerged.

CAUTION:

• The product is specially designed for charging QC, PD compatible devices and 12v plug only.
• This product does not contain any user serviceable parts. DO NOT attempt to repair or modify the product in any way.

When used in high ambient temperature or in direct sunlight, the product may turn off temporarily, this is a safety feature of the electronics. The IP protection rating is only valid if the installation is carried out correctly according to the instructions and on a perfectly flat, smooth and non-porous surface. When choosing a mounting location, avoid areas exposed to heat radiation devices and areas with poor ventilation.

WIRING:

Professional electrician installation recommended, see Technical Information for power requirements. To achieve max power output, the specified voltage must be at the charger. Battery performance and voltage drop needs to be considered for installation.

ENVIRONMENTAL PROTECTION:

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

IMPORTANT

• Scanstrut Ltd & Inc. accepts no responsibility for any injuries or other damages arising from the use of their products in any circumstances.

WARRANTY

A 2 year, non-transferrable warranty covers this Scanstrut product only and not any devices that are charged by it. No warranty is given for users’ devices and users expose their devices to hazards, known or unknown, at their own risk.

Certification

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:

• The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
• During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.

Scanstrut Ltd, declares the product

‘Flip Pro DUO’ SKU: SC-MULTI-F2 is in compliance with EMC CE-RED Directive (2014/30/EU) & The CE certificate of EN55032, EN55035, EN61000 conformity can be found at www.scanstrut.com/support/compliance

Introducing

Flip Pro Duo.

USB-A/USB-C & 12V power socket.

Combing features of our high power Flip Pro USB-A / C charger and 12V Power Sockets into a beautiful multi power solution.
When not in use, the spring-loaded caps remain tightly closed, protecting the ports from the elements.

Universal

• Universal fit for any USB-A & C connectors
• Fast charge (6OW max) up to 2 devices at a time

Marine Ready

• IPX4 waterproof with the cover closed
• UV resistant
• 316 stainless hinge and spring

Electrical Information

• 120 -150W max power 12V system only (12V Socket)
• Input voltage: 10-30V DC (12/24V System)
• Input current Max: 6A (10A fuse recommended)

Installation

Easy Install, using a standard 032mm (1.25″) hole saw

USB Data

12V 3A MAX

Output Type C (24V System)| 5V 3A, 9V 3A

12V 3A, 15V 3A

20V 3A MAX

Output Type A Max| 5V 1.5A, 9V 1.5A

12V 1.5A/3A MAX

Waterproof rating| IPX4
Standby draw| 0.01W
Certification| CE, FCC, UKCA, C-Tick, ROHS

Contact

• www.scanstrut.com
• USA: 860-308-1416, option 2
• Canada: usasales@scanstrut.com
• UK: +44 (0) 1392 531280
• EMEA APAC:sales@scanstrut.com

Share your install

Documents / Resources

| SCANSTRUT SC-MULTI-F2 Flip Pro Duo [pdf] Instruction Manual
SC-MULTI-F2 Flip Pro Duo USB-A and USB-C With 12V Power Socket, SC-MULTI-F2, Flip Pro Duo USB-A and USB-C With 12V Power Socket, USB-C With 12V Power Socket, Power Socket
---|---

References

• Mounts, Waterproof Wireless Chargers, Cable Seals for Marine and Outdoor Technology | Scanstrut

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>