SCANSTRUT SC-CW-11F Rokk Wireless Active Charging Cradle Instruction Manual
- June 3, 2024
- SCANSTRUT
Table of Contents
SCANSTRUT SC-CW-11F Rokk Wireless Active Charging Cradle
Installation Instructions
-
Unbox Nano and insert the installation jig.
-
Ensure there is sufficient clearance to open the jaws in the chosen installation area.
-
Ensure Nano is Horizontal and the installation area is flat.
-
Use a drilling template to drill x4 pilot holes (see tools required table).
-
Feed cable through the hole.
Apply sealant to x4 screws.
Screw the product in place.
Remove the installation jig. -
Connect wires or connectors to 12/24V supply, ensuring a waterproof connection. Fuse according to the input voltage and current.
USER GUIDE
Place the device centrally within the Nano jaws.
ROKK WIRELESS – NANO 10W (SC-CW-11F)
IN EXTREME USAGE ENVIRONMENTS PERFORMANCE MAY VARY.
This product is designed to securely mount phones under normal usage
conditions. The end-user is entirely responsible for the conditions in which
their device is used. See the WARRANTY section for further details.
Scanstrut recommends installation is carried out by a qualified electrician.
No liability is accepted for damage and/or injury caused by incorrect
installation.
WARNING
This product is to be connected to a 12V DC or 24V DC battery power source
only. The power supply must be switched off before installation.
appropriate fuse or circuit breaker must be used between the battery/power
source and this product. Check for the correct polarity of all wiring before
switching the power on. This product may contain high voltages. Do not tamper
with the product. This product is NOT approved for use in hazardous/flammable
atmospheres. Do NOT install in a hazardous/flammable atmosphere e.g. engine
room.
Before drilling any holes, ensure the area behind the mounting location is clear of wires, fuel, and all other hazardous objects. Ensure any holes cut will not significantly weaken the structure of the mounting surface. If the product needs to be mounted outside, it must be mounted in a location safely above the waterline, where it is not at risk of being submerged. Full strength is not achieved until the product is installed
CAUTION
The product is designed specifically for the charging of Qi-compatible
devices. The cable must be retained and not interfere with mechanical systems.
This product contains no user-serviceable components. Do NOT attempt to repair
or alter the product in any way. This product will charge through non-metallic
phone cases up to ~3mm thick. Phone cases may alter overall charge
performance. When used in a very high/low ambient temperature/direct or
prolonged sunlight the product may temporarily shut down, this is a safety
feature of the electronics.
The IP rating is only valid if correctly installed as per these instructions and on a perfectly flat, non-porous, smooth surface. When selecting a mounting location, avoid places exposed to heat-radiating appliances and poorly ventilated areas.
EMC INSTALLATION GUIDELINES
Scanstrut products conform to Electromagnetic Compatibility (EMC) regulations,
to ensure that electromagnetic interference between equipment is minimized.
Correct installation is required to ensure that electromagnetic interference
is kept to a minimum.
WIRING
When extending the cable from the battery/power source to the product, ensure
there is consistently a minimum of 10V being provided to the product. A wire
gauge of 18AWG (0.82mm2) is recommended for any length of cable extension. The
electrical schematic is to illustrate how the product should be connected to a
12V DC or 24V DC battery/power supply.
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
IMPORTANT
Scanstrut Ltd. accepts no responsibility for any injuries or other damages
arising from the use of its products in any circumstances.
WARRANTY
A 2-year, non-transferable warranty covers this Scanstrut product only and not
any devices that are mounted in it or on it. No warranty is given for users’
devices and users expose their devices to hazards, known or unknown, at their
own risk. For further installation and warranty information please visit:
www.scanstrut.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>